Effect of Heat Treatment on Microstructure and Mechanical Properties of a Selective Laser Melting Processed Ni-Based Superalloy GTD222.

Additive manufacturing (AM) of nickel-based superalloys is of high interest for application in complex hot end parts. However, it has been widely suggested that the microstructure-properties of the additive manufacturing processed superalloys are not yet fully clear. In this study, the GTD222, an important superalloy for high-temperature hot-end part, were prepared using selective laser melting and then subjected to heat treatment. The microstructure evolution of the GTD222 was investigated and the mechanical properties of heat treated GTD222 were tested. The results have shown that the grain size of the heat treated GTD222 was close to its as-built counterparts. Meanwhile, a large amount of γ' and nano-scaled carbides were precipitated in the heat treated GTD222. The microstructure characteristics implied that the higher strength of the heat treated GTD222 can be attributed to the γ' and nano-scaled carbides. This study provides essential microstructure and mechanical properties information for optimizing the heat treatment process of the AM processed GTD222.

The treatment and risk factors of retinopathy of prematurity in neonatal intensive care units.

BACKGROUND: Retinopathy of prematurity (ROP) is a vascular proliferative disorder of the developing retina and a significant cause of childhood blindness around the world. The incidence of ROP is affected by many factors, and the incidence rate varies from country to country. The purpose of this study is to report the incidence and risk factors of ROP in neonatal intensive care unit (NICU) of Guangzhou First People's Hospital in China. METHODS: A retrospective review was performed on 436 premature infants who were consecutive ROP screened in the NICU of Guangzhou First People's Hospital from March 2013 to October 2017. The single-factor analysis and the logistic multivariate regression analysis were used to detect risk factors of ROP. RESULTS: Total 436 premature infants were consecutive ROP screened, 138 (31.65%) were found ROP, and 61(13.99%) were treated. The single-factor analysis revealed that the incidence of ROP was associated with multiple births, gestational age, birth weight, mechanical ventilation, intravascular hemolysis, the number of operations and blood culture results. The logistic multivariate regression analysis revealed that gestational age; birth weight, mechanical ventilation, minimum SaO2 and daily weight gain were independent risk factors for ROP onset. Forty-nine patients underwent retinal laser photocoagulation with recurrence 20 patients. Twelve patients underwent anti-VEGF drug (Ranibizumab) via intraocular injection with 5 patients of recurrence. CONCLUSIONS: The incidence of ROP in NICU of Guangzhou China will match those in middle-income countries, but higher than high-income countries. Anti-VEGF drugs could be preferred as a good treatment method for zone 1 ROP and aggressive posterior ROP.

Flexural and compressive mechanical behaviors of the porous titanium materials with entangled wire structure at different sintering conditions for load-bearing biomedical applications.

The entangled titanium materials with various porosities have been investigated in terms of the flexural and compressive mechanical properties and the deformation and failure modes. The effect of the sintering parameters on the mechanical properties and the porosity reduction has been comprehensively studied. The results indicate that both the flexural and compressive mechanical properties increase significantly as the porosity decreases. In the porosity range investigated the flexural elastic modulus is in the range of 0.05-6.33GPa, the flexural strength is in the range of 9.8-324.9MPa, the compressive elastic modulus is in the range of 0.03-2.25GPa, and the compressive plateau stress is in the range of 2.3-147.8MPa. The mechanical properties of the entangled titanium materials can be significantly improved by sintering, which increase remarkably as the sintering temperature and/or the sintering time increases. But on other hand, the sintering process can induce the porosity reduction due to the oxidation on the titanium wire surface.

Porous titanium materials with entangled wire structure for load-bearing biomedical applications.

A kind of porous metal-entangled titanium wire material has been investigated in terms of the pore structure (size and distribution), the strength, the elastic modulus, and the mechanical behavior under uniaxial tensile loading. Its functions and potentials for surgical application have been explained. In particular, its advantages over competitors (e.g., conventional porous titanium) have been reviewed. In the study, a group of entangled titanium wire materials with non-woven structure were fabricated by using 12-180 MPa forming pressure, which have porosity in a range of 48%-82%. The pores in the materials are irregular in shape, which have a nearly half-normal distribution in size range. The yield strength, ultimate tensile strength, and elastic modulus are 75 MPa, 108 MPa, and 1.05 GPa, respectively, when its porosity is 44.7%. The mechanical properties decrease significantly as the porosity increases. When the porosity is 57.9%, these values become 24 MPa, 47.5 MPa, and 0.33 GPa, respectively. The low elastic modulus is due to the structural flexibility of the entangled titanium wire materials. For practical reference, a group of detailed data of the porous structure and the mechanical properties are reported. This kind of material is very promising for implant applications because of their very good toughness, perfect flexibility, high strength, adequate elastic modulus, and low cost.