High-Performance PEEK/MWCNT Nanocomposites: Combining Enhanced Electrical Conductivity and Nanotube Dispersion.

High-performance engineering thermoplastics offer lightweight and excellent mechanical performance in a wide temperature range. Their composites with carbon nanotubes are expected to enhance mechanical performance, while providing thermal and electrical conductivity. These are interesting attributes that may endow additional functionalities to the nanocomposites. The present work investigates the optimal conditions to prepare polyether ether ketone (PEEK)/multi-walled carbon nanotube (MWCNT) nanocomposites, minimizing the MWCNT agglomerate size while maximizing the nanocomposite electrical conductivity. The aim is to achieve PEEK/MWCNT nanocomposites that are suitable for melt-spinning of electrically conductive multifilament's. Nanocomposites were prepared with compositions ranging from 0.5 to 7 wt.% MWCNT, showing an electrical percolation threshold between 1 and 2 wt.% MWCNT (107-102 S/cm) and a rheological percolation in the same range (1 to 2 wt.% MWCNT), confirming the formation of an MWCNT network in the nanocomposite. Considering the large drop in electrical conductivity typically observed during melt-spinning and the drawing of filaments, the composition PEEK/5 wt.% MWCNT was selected for further investigation. The effect of the melt extrusion parameters, namely screw speed, temperature, and throughput, was studied by evaluating the morphology of MWCNT agglomerates, the nanocomposite rheology, and electrical properties. It was observed that the combination of the higher values of screw speed and temperature profile leads to the smaller number of MWCNT agglomerates with smaller size, albeit at a slightly lower electrical conductivity. Generally, all processing conditions tested yielded nanocomposites with electrical conductivity in the range of 0.50-0.85 S/cm. The nanocomposite processed at higher temperature and screw speed presented the lowest value of elastic modulus, perhaps owing to higher matrix degradation and lower connectivity between the agglomerates. From all the process parameters studied, the screw speed was identified to have the higher impact on nanocomposite properties.

Experimental Validation of a Micro-Extrusion Set-Up with In-Line Rheometry for the Production and Monitoring of Filaments for 3D-Printing.

The main objective of this work is to validate an in-line micro-slit rheometer and a micro-extrusion line, both designed for the in-line monitoring and production of filaments for 3D printing using small amounts of material. The micro-filament extrusion line is first presented and its operational window is assessed. The throughputs ranged between 0.045 kg/h and 0.15 kg/h with a maximum 3% error and with a melt temperature control within 1 °C under the processing conditions tested for an average residence time of about 3 min. The rheological micro slit is then presented and assessed using low-density polyethylene (LDPE) and cyclic olefin copolymer (COC). The excellent matching between the in-line micro-rheological data and the data measured with off-line rotational and capillary rheometers validate the in-line micro-slit rheometer. However, it is shown that the COC does not follow the Cox-Merz rule. The COC filaments produced with the micro-extrusion line were successfully used in the 3D printing of specimens for tensile testing. The quality of both filaments (less than 6% variation in diameter along the filament's length) and printed specimens validated the whole micro-set-up, which was eventually used to deliver a rheological mapping of COC printability.

Cellulose Nanocrystal (CNC) Gels: A Review.

The aim of this article is to review the research conducted in the field of aqueous and polymer composites cellulose nanocrystal (CNC) gels. The experimental techniques employed to characterize the rheological behavior of these materials will be summarized, and the main advantages of using CNC gels will also be addressed in this review. In addition, research devoted to the use of numerical simulation methodologies to describe the production of CNC-based materials, e.g., in 3D printing, is also discussed. Finally, this paper also discusses the application of CNC gels along with additives such as cross-linking agents, which can represent an enormous opportunity to develop improved materials for manufacturing processes.

In-Line Rheo-Optical Investigation of the Dispersion of Organoclay in a Polymer Matrix during Twin-Screw Compounding.

The dispersion mechanisms in a clay-based polymer nanocomposite (CPNC) during twin-screw extrusion are studied by in-situ rheo-optical techniques, which relate the CPNC morphology with its viscosity. This methodology avoids the problems associated with post extrusion structural rearrangement. The polydimethylsiloxane (PDMS) matrix, which can be processed at ambient and low temperatures, is used to bypass any issues associated with thermal degradation. Local heating in the first part of the extruder allows testing of the usefulness of low matrix viscosity to enhance polymer intercalation before applying larger stresses for clay dispersion. The comparison of clay particle sizes measured in line with models for the kinetics of particle dispersion indicates that larger screw speeds promote the break-up of clay particles, whereas smaller screw speeds favor the erosion of the clay tactoids. Thus, different levels of clay dispersion are generated, which do not simply relate to a progressively better PDMS intercalation and higher clay exfoliation as screw speed is increased. Reducing the PDMS viscosity in the first mixing zone of the screw facilitates dispersion at lower screw speeds, but a complex interplay between stresses and residence times at larger screw speeds is observed. More importantly, the results underline that the use of larger stresses is inefficient per se in dispersing clay if sufficient time is not given for PDMS to intercalate the clay galleries and thus facilitate tactoid disruption or erosion.

Wastewater-Based Epidemiology (WBE) and Viral Detection in Polluted Surface Water: A Valuable Tool for COVID-19 Surveillance-A Brief Review.

SARS-CoV-2 is the causative agent of the current COVID-19 pandemic. Disease clinical manifestations range from asymptomatic to severe multiple organ damage. SARS-CoV-2 uses ACE2 as a cellular receptor, which is abundantly expressed in the small intestine, allowing viral replication in the gastrointestinal tract. Viral RNA has been detected in the stool of COVID-19 patients and viable viruses had been isolated in some of these samples. Thus, a putative role of SARS-CoV-2 fecal-oral transmission has been argued. SARS-CoV-2 is shed in human excreta and further disposed in the sewerage or in the environment, in poor basic sanitation settings. Wastewater-based epidemiology (WBE) is a valuable population level approach for monitoring viral pathogens and has been successfully used in different contexts. This review summarizes the current global experience on SARS-CoV-2 WBE in distinct continents and viral detection in polluted surface water. The advantages and concerns of this strategy for SARS-CoV-2 surveillance are discussed. Outcomes suggest that WBE is a valuable early warning alert and a helpful complementary surveillance tool to subside public health response, to tailor containment and mitigation measures and to determine target populations for testing. In poor sanitation settings, contaminated rivers could be alternatively used as a source for environmental surveillance.

Wastewater-Based Epidemiology (WBE) and Viral Detection in Polluted Surface Water: A Valuable Tool for COVID-19 Surveillance: A Brief Review

SARS-COV-2 is the causative agent of the current COVID-19 pandemic. Disease clinical manifestations range from asymptomatic to severe multiple organ damage. SARS-CoV-2 uses ACE2 as a cellular receptor, which is abundantly expressed in the small intestine, allowing viral replication in the gastrointestinal tract. Viral RNA has been detected in the stool of COVID-19 patients and viable viruses had been isolated in some of these samples. Thus, a putative role of SARS-CoV-2 fecal-oral transmission has been argued. SARS-CoV-2 is shed in human excreta and further disposed in the sewerage or in the environment, in poor basic sanitation settings. Wastewater-based epidemiology (WBE) is a valuable population level approach for monitoring viral pathogens and has been successfully used in di_erent contexts. This review summarizes the current global experience on SARS-CoV-2 WBE in distinct continents and viral detection in polluted surface water. The advantages and concerns of this strategy for SARS-CoV-2 surveillance are discussed. Outcomes suggest that WBE is a valuable early warning alert and a helpful complementary surveillance tool to subside public health response, to tailor containment and mitigation measures and to determine target populations for testing. In poor sanitation settings, contaminated rivers could be alternatively used as a source for environmental surveillance.

Priorities to reduce the burden of stroke in Latin American countries.

The large and increasing burden of stroke in Latin American countries, and the need to meet the UN and WHO requirements for reducing the burden from non-communicable disorders (including stroke), brought together stroke experts and representatives of the Ministries of Health of 13 Latin American countries for the 1st Latin American Stroke Ministerial meeting in Gramado, Brazil, to discuss the problem and identify ways of cooperating to reduce the burden of stroke in the region. Discussions were focused on the regional and country-specific activities associated with stroke prevention and treatment, including public stroke awareness, prevention strategies, delivery and organisation of care, clinical practice gaps, and unmet needs. The meeting culminated with the adoption of the special Gramado Declaration, signed by all Ministerial officials who attended the meeting. With agreed priorities for stroke prevention, treatment, and research, an opportunity now exists to translate this Declaration into an action plan to reduce the burden of stroke.