Quantification of natural gas and other hydrocarbons from production sites in northern West Virginia using tracer flux ratio methodology.

Tracer flux ratio (TFR) methodology performed downwind of 15 active oil and natural gas production sites in Ohio County, West Virginia sought to quantify air pollutant emissions over two weeks in April 2018. In coordination with a production company, sites were randomly selected depending on wind forecasts and nearby road access. Methane (CH4), ethane (C2H6), and tracer gas compounds (acetylene and nitrous oxide) were measured via tunable infrared direct absorption spectroscopy. Ion signals attributed to benzene (C6H6) and other volatile gases (e.g., C7 - C9 aromatics) were measured via proton-transfer reaction time-of-flight mass spectrometry. Short-term whole facility emission rates for 12 sites are reported. Results from TFR were systematically higher than the sum of concurrent on-site full flow sampler measurements, though not all sources were assessed on-site in most cases. In downwind plumes, the mode of the C2H6:CH4 molar ratio distribution for all sites was 0.2, which agreed with spot sample analysis from the site operator. Distribution of C6H6:CH4 ratios was skew but values between 1 and 5 pptv ppbv-1 were common. Additionally, the aromatic profile has been attributed to condensate storage tank emissions. Average ratios of C7 - C9 to C6H6 were similar to other literature values reported for natural gas wells.

Assessment of Chemical Facility Ethylene Oxide Emissions Using Mobile and Multipoint Monitoring.

Ethylene oxide (EtO) is a hazardous air pollutant that can be emitted from a variety of difficult to measure industrial sources, such as fugitive leaks, wastewater handling, and episodic releases. Emerging next generation emission measurement (NGEM) approaches capable of time-resolved, low parts per billion by volume (ppbv) method detection limits (MDLs) can help facilities understand and reduce EtO and other air pollutant emissions from these sources yielding a range of environmental and public health benefits. In October 2021, a first of its kind 4-day observational study was conducted at an EtO chemical facility in the midwestern United States. The study had dual objectives to both improve understanding of EtO emission sources within the facility and advance NGEM methods. Using cavity ring-down spectroscopy (CRDS) instruments, a combination of mobile surveys and stationary multipoint process unit monitoring assessed EtO concentrations in and near facility operations, while testing and comparing measurement methods. The study concluded that four main areas of EtO source emissions existed within the facility, each possessing unique emission characteristics. Episodic EtO emissions from supply railcar switchovers and batch reactor washouts, lasting seconds to minutes in duration, produced EtO concentrations exceeding 500 ppbv inside the process unit in some cases. In one instance, EtO at ~30 ppbv was briefly observed hundreds of meters from the process unit. Lower level but more sustained EtO concentrations were observed near an EtO transfer pump and wastewater tank outfall and drain system. Overall, 4.6% of mobile survey data were above the 1.2 ppbv mobile test MDL while the nine stationary sampling locations ranged from 17.7% to 82.8% of data above the 1.0 ppbv multipoint test MDL. This paper describes the EtO emissions observed in and near the four defined source areas within the facility and provides details of the NGEM method development advances accomplished as part of the study.

Evaluating Natural Gas Emissions from Pneumatic Controllers from Upstream Oil and Gas Facilities in West Virginia.

In April of 2018, an optical gas imaging (OGI) and full flow sampler (FFS) emissions measurement study of pneumatic controllers (PCs) was conducted at 15 oil and natural gas production sites in West Virginia. The objective of the study was to identify and characterize PC systems with excessive emissions caused by maintenance issues or nonoptimized process conditions. A total of 391 PC systems were found on the sites and all were classified by the operator as snap-acting (on/off) intermittent venting PCs (IPCs) that should exhibit little gas release while the PC is closed between actuation events. The population was comprised of two groups, 259 infrequently actuating, lower emitting (LE) IPCs and 132 gas processing unit (GPU) liquid level IPCs and associated dump valve actuators that vent more frequently and have larger emission volumes. Using a PC-specific OGI inspection protocol with an assumed whole gas OGI detection threshold of 2.0 scfh, only 2 out of 259 LE-IPCs exhibited OGI detectable emissions indicating good inspection and maintenance practices for this category. Due to combined (ganged) GPU exhaust vents, the OGI inspection of the GPU liquid level IPCs was comparatively less informative and determination of single component IPC emissions by the FFS was more difficult. The time resolved FFS measurements of GPU IPCs defined three categories of operation: one that indicated proper function and two associated with higher emissions that may result from an IPC maintenance or process issues. The overall GPU IPC emission distribution was heavy tailed, with a median value of 12.8 scfh, similar to the 13.5 scfh whole gas IPC emission factor (EF). Total emissions were dominated by non-optimal temporal profile high-emitter IPC cases with the top 20% of IPC systems accounting for between 51.3% and 70.7% of GPU liquid level IPC emissions by volume. The uncertainty in the estimate was due to the ganged nature of the GPU exhaust vents. The highest GPU IPC emission came from a single malfunctioning unit with a measured whole gas value of 157 scfh. Up to six IPCs exceeded 100 scfh. An analysis of FFS emission measurements compared to liquids production per IPC unit employed indicated that production sites operating at a high level of liquids production test the limits of the site engineering, likely resulting in higher IPC emissions. Overall, this study found that the LE-IPCs with OGI-verified low closed bleed rates may emit well below the IPC EF while GPU liquid level IPC systems are likely well represented by the current IPC EF. IPCs that are experiencing a maintenance or process issue or that are operating at sites with a very high product throughput per IPC employed can emit at rates exceeding ten times IPC EF.

Pyrolysis processing of PFAS-impacted biosolids, a pilot study.

Concentrations of per- and poly-fluoroalkyl substances (PFAS) present in wastewater treatment biosolids are a growing concern. Pyrolysis is a thermal treatment technology for biosolids that can produce a useful biochar product with reduced levels of PFAS and other contaminants. In August 2020, a limited-scope study investigated target PFAS removal of a commercial pyrolysis system processing biosolid with the analysis of 41 target PFAS compounds in biosolids and biochar performed by two independent laboratories. The concentrations of 21 detected target compounds in the input biosolids ranged between approximately 2 µg/kg and 85 µg/kg. No PFAS compounds were detected in the biochar. The PFAS concentrations in the biochar were assumed to equal the compounds' minimum detection limits (MDLs). The pyrolysis system's target PFAS removal efficiencies (REs) were estimated to range between >81.3% and >99.9% (mean >97.4%) with the lowest REs being associated with the lowest detected PFAS concentrations and the highest MDLs. No information on non-target PFAS compounds in influent or effluent media or products of incomplete combustion was considered. Selected gaseous emissions were measured by Fourier transform infrared spectroscopy and gas chromatography time-of-flight mass spectrometry to provide additional information on air emissions after process controls. This limited-scope study indicated that additional research to further understand this process is warranted.Implications: Development of alternative approaches to manage PFAS-impacted biosolids is of emerging international importance. A commercially operating biosolid pyrolysis process was shown to lower target PFAS levels in produced biochar. Additional research is warranted to understand all potential PFAS transformation emission routes and optimal air pollution emissions control strategies for this technology class.

Methane emissions from oil and gas production sites and their storage tanks in West Virginia.

A measurement campaign characterized methane and other emissions from 15 natural gas production sites. Sites were surveyed using optical gas imaging (OGI) cameras to identify fugitive and vented emissions, with the methane mass emission rate quantified using a full flow sampler. We present storage tank emissions in context of all site emissions, followed by a detailed account of the former. In total, 224 well pad emission sources at 15 sites were quantified yielding a total emission rate of 57.5 ± 2.89 kg/hr for all sites. Site specific emissions ranged from 0.4 to 10.5 kg/hr with arithmetic and geometric means of 3.8 and 2.2 kg/hr, respectively. The two largest categories of emissions by mass were pneumatic devices (35 kg/hr or ~61% of total) and tanks (14.3 kg/hr or ~25% of total). Produced water and condensate tanks at all sites employed emissions control devices. Nevertheless, tanks may still lose gas via component leaks as observed in this study. The total number of tanks at all sites was 153. One site experienced a major malfunction and direct tank measurements were not conducted due to safety concerns and may have represented a super-emitter as found in other studies. The remaining sites had 143 tanks, which accounted for 42 emissions sources. Leaks on controlled tanks were associated with ERVs, PRVs, and thief hatches. Since measurements represented snapshots-in-time and could only be compared with modeled tank emission data, it was difficult to assess real capture efficiencies accurately. Our estimates suggest that capture efficiency ranged from 63 to 92% for controlled tanks.

Spatial analysis of volatile organic compounds using passive samplers in the Rubbertown industrial area of Louisville, Kentucky, USA.

Select volatile organic compounds (VOCs) were measured in the vicinity of chemical facilities and other operations in the Rubbertown industrial area of Louisville, Kentucky (USA) using modified EPA Methods 325A/B passive sampler tubes. Two-week, time-integrated passive samplers were deployed at ten sites which were aggregated into three site groups of varying distances from the Rubbertown area facilities. In comparison to canister data from 2001 to 2005, two of the sites suggested generally lower current VOC levels. Good precision was obtained from the duplicate tubes (≤ 12%) for benzene, toluene, ethylbenzene, and xylene isomers (BTEX), styrene, 1,3-butadiene, perchloroethylene, and other trace VOCs. BTEX, styrene, and 1,3-butadiene concentrations were statistically significantly higher at two site groups near Rubbertown sources than the site group farther away. As found in a similar study in South Philadelphia, BTEX concentrations were also lower for sites farther from a source, though the decline was less pronounced on a percentage basis in Rubbertown. These results suggest that EPA Methods 325A/B can be useful to assess VOC gradients for emissions from chemical facilities besides fenceline benzene levels from refineries.

Understanding oil and gas pneumatic controllers in the Denver-Julesburg basin using optical gas imaging.

In the spring of 2018, a 10-day field study was conducted in Colorado's Denver-Julesburg oil and natural gas production basin to improve information on well pad pneumatic controller (PC) populations and identify PCs with potential maintenance issues (MIs) causing excess emissions through a novel optical gas imaging (OGI) survey approach. A total of 500 natural gas-emitting PCs servicing 102 wells (4.9 PCs/well) were surveyed at 31 facilities operated by seven different companies. The PCs were characterized by their designed operational function and applications, with 83% of the PC population identified as intermittent PCs (IPCs). An OGI inspection protocol was used to investigate emissions on 447 working PCs from this set. OGI detected continuous emissions from 11.3% of observed IPCs and these were classified as experiencing some level of MIs. OGI imaging modes were observed to have a significant effect on emission detectability with high sensitivity mode detection rates being approximately 2 times higher compared to auto mode. Fourteen snapshot emission measurements (not including actuations) were conducted on IPCs in this category using a high-volume sampling device with augmented quality assurance procedures with observed emissions rates ranging from 0.1 up to 31.3 scf/hr (mean = 2.8 scf/hr). For PCs with continuous depressurization type (CPC), 36.8% had continuous emissions observed by OGI. Four supporting emission measurements were conducted on CPCs with one unit exceeding the low bleed regulatory emission threshold with an emission rate of 9.9 scf/hr (mean = 4.2 scf/hr). Additional information was collected on PC actuation events, as observed with OGI, which showed a strong correlation between observed actuation events and facility production compared to observed continuous emissions caused by MIs which did not correlate with facility production.Implications: A novel survey approach of pneumatic controllers at oil and natural gas production facilities in the Denver-Julesburg basin, using optical gas imaging and supporting emission measurements, was demonstrated as an effective method to identify controllers with potential maintenance issues causing excess emissions. The results of the pneumatic controller and optical gas imaging surveys improved information on pneumatic controller populations within the basin and also demonstrated the significant effect optical gas imaging modes have on emission detections.

Assessment of Uinta Basin Oil and Natural Gas Well Pad Pneumatic Controller Emissions.

In the fall of 2016, a field study was conducted in the Uinta Basin Utah to improve information on oil and natural gas well pad pneumatic controllers (PCs). A total of 80 PC systems at five oil sites (supporting six wells) and three gas sites (supporting 12 wells) were surveyed, and emissions data were produced using a combination of measurements and engineering emission estimates. Ninety-six percent of the PCs surveyed were low actuation frequency intermittent vent type. The overall whole gas emission rate for the study was estimated at 0.36 scf/h with the majority of emissions occurring from three continuous vent PCs (1.0 scf/h average) and eleven (14%) malfunctioning intermittent vent PC systems (1.6 scf/h average). Oil sites employed, on average 10.3 PC systems per well compared to 1.5 for gas sites. Oil and gas sites had group average PC emission rates of 0.28 scf/h and 0.67 scf/h, respectively, with this difference due in part to site selection procedures. The PC system types encountered, the engineering emissions estimate approach, and comparisons to measurements are described. Survey methods included identification of malfunctioning PC systems and emission measurements with augmented high volume sampling and installed mass flow meters, each providing a somewhat different picture of emissions that are elucidated through example cases.

Sample integrity evaluation and EPA method 325B interlaboratory comparison for select volatile organic compounds collected diffusively on Carbopack X sorbent tubes.

A sample integrity evaluation and an interlaboratory comparison were conducted in application of U.S. Environmental Protection Agency (EPA) Methods 325A and 325B for diffusively monitoring benzene and other selected volatile organic compounds (VOCs) using Carbopack X sorbent tubes. To evaluate sample integrity, VOC samples were refrigerated for up to 240 days and analyzed using thermal desorption/gas chromatography-mass spectrometry at the EPA Office of Research and Development laboratory in Research Triangle Park, NC, USA. For the interlaboratory comparison, three commercial analytical laboratories were asked to follow Method 325B when analyzing samples of VOCs that were collected in field and laboratory settings for EPA studies. Overall results indicate that the selected VOCs collected diffusively on sorbent tubes generally were stable for 6 months or longer when samples were refrigerated. This suggests the specified maximum 30-day storage time of VOCs collected diffusively on Carbopack X passive samplers and analyzed using Method 325B might be able to be relaxed. Interlaboratory comparison results were in agreement for the challenge samples collected diffusively in an exposure chamber in the laboratory, with most measurements within ±25% of the theoretical concentration. Statistically significant differences among laboratories for ambient challenge samples were small, less than 1 part per billion by volume (ppbv). Results from all laboratories exhibited good precision and generally agreed well with each other.

Comparison of Field Measurements to Methane Emissions Models at a New Landfill.

Estimates of methane emissions from landfills rely primarily on models due to both technical and economic limitations. While models are easy to implement, there is uncertainty due to the use of parameters that are difficult to validate. The objective of this research was to compare modeled emissions using several greenhouse gas (GHG) emissions reporting protocols including: (1) Intergovernmental Panel on Climate Change (IPCC); (2) U.S. Environmental Protection Agency Greenhouse Gas Reporting Program (EPA GHGRP); (3) California Air Resources Board (CARB); and (4) Solid Waste Industry for Climate Solutions (SWICS), with measured emissions data collected over three calendar years from a young landfill with no gas collection system. By working with whole landfill measurements of fugitive methane emissions and methane oxidation, the collection efficiency could be set to zero, thus eliminating one source of parameter uncertainty. The models consistently overestimated annual methane emissions by a factor ranging from 4-31. Varying input parameters over reasonable ranges reduced this range to 1.3-8. Waste age at the studied landfill was less than four years and the results suggest the need for measurements at additional landfills to evaluate the accuracy of the tested models to young landfills.

South Philadelphia passive sampler and sensor study.

UNLABELLED: From June 2013 to March 2015, in total 41 passive sampler deployments of 2 wk duration each were conducted at 17 sites in South Philadelphia, PA, with results for benzene discussed here. Complementary time-resolved measurements with lower cost prototype fenceline sensors and an open-path ultraviolet differential optical absorption spectrometer were also conducted. Minimum passive sampler benzene concentrations for each sampling period ranged from 0.08 ppbv to 0.65 ppbv, with a mean of 0.25 ppbv, and were negatively correlated with ambient temperature (-0.01 ppbv/°C, R(2) = 0.68). Co-deployed duplicate passive sampler pairs (N = 609) demonstrated good precision with an average and maximum percent difference of 1.5% and 34%, respectively. A group of passive samplers located within 50 m of a refinery fenceline had a study mean benzene concentration of 1.22 ppbv, whereas a group of samplers located in communities >1 km distant from facilities had a mean of 0.29 ppbv. The difference in the means of these groups was statistically significant at the 95% confidence level (p < 0.001). A decreasing gradient in benzene concentrations moving away from the facilities was observed, as was a significant period-to-period variation. The highest recorded 2-wk average benzene concentration for the fenceline group was 3.11 ppbv. During this period, time-resolved data from the prototype sensors and the open-path spectrometer detected a benzene signal from the west on one day in particular, with the highest 5-min path-averaged benzene concentration measured at 24 ppbv. IMPLICATIONS: Using a variation of EPA's passive sampler refinery fenceline monitoring method, coupled with time-resolved measurements, a multiyear study in South Philadelphia informed benzene concentrations near facilities and in communities. The combination of measurement strategies can assist facilities in identification and mitigation of emissions from fugitive sources and improve information on air quality complex air sheds.

Spatial analysis of volatile organic compounds in South Philadelphia using passive samplers.

UNLABELLED: Select volatile organic compounds (VOCs) were measured in the vicinity of a petroleum refinery and related operations in South Philadelphia, Pennsylvania, USA, using passive air sampling and laboratory analysis methods. Two-week, time-integrated samplers were deployed at 17 sites, which were aggregated into five site groups of varying distances from the refinery. Benzene, toluene, ethylbenzene, and xylene isomers (BTEX) and styrene concentrations were higher near the refinery's fenceline than for groups at the refinery's south edge, mid-distance, and farther removed locations. The near fenceline group was significantly higher than the refinery's north edge group for benzene and toluene but not for ethylbenzene or xylene isomers; styrene was lower at the near fenceline group versus the north edge group. For BTEX and styrene, the magnitude of estimated differences generally increased when proceeding through groups ever farther away from the petroleum refining. Perchloroethylene results were not suggestive of an influence from refining. These results suggest that emissions from the refinery complex contribute to higher concentrations of BTEX species and styrene in the vicinity of the plant, with this influence declining as distance from the petroleum refining increases. IMPLICATIONS: Passive sampling methodology for VOCs as discussed here is employed in recently enacted U.S. Environmental Protection Agency Methods 325A/B for determination of benzene concentrations at refinery fenceline locations. Spatial gradients of VOC concentration near the refinery fenceline were discerned in an area containing traffic and other VOC-related sources. Though limited, these findings can be useful in application of the method at such facilities to ascertain source influence.

Volatile organic compounds at two oil and natural gas production well pads in Colorado and Texas using passive samplers.

UNLABELLED: A pilot study was conducted in application of the U.S. Environmental Protection Agency (EPA) Methods 325A/B variant for monitoring volatile organic compounds (VOCs) near two oil and natural gas (ONG) production well pads in the Texas Barnett Shale formation and Colorado Denver-Julesburg Basin (DJB), along with a traffic-dominated site in downtown Denver, CO. As indicated in the EPA method, VOC concentrations were measured for 14-day sampling periods using passive-diffusive tube samplers with Carbopack X sorbent at fenceline perimeter and other locations. VOCs were significantly higher at the DJB well pad versus the Barnett well pad and were likely due to higher production levels at the DJB well pad during the study. Benzene and toluene were significantly higher at the DJB well pad versus downtown Denver. Except for perchloroethylene, VOCs measured at passive sampler locations (PSs) along the perimeter of the Barnett well pad were significantly higher than PSs farther away. At the DJB well pad, most VOC concentrations, except perchloroethylene, were significantly higher prior to operational changes than after these changes were made. Though limited, the results suggest passive samplers are precise (duplicate precision usually ≤10%) and that they can be useful to assess spatial gradients and operational conditions at well pad locations over time-integrated periods. IMPLICATIONS: Recently enacted EPA Methods 325A/B use passive-diffusive tube samplers to measure benzene at multiple fenceline locations at petrochemical refineries. This pilot study presents initial data demonstrating the utility of Methods 325A/B for monitoring at ONG facilities. Measurements revealed elevated concentrations reflective of production levels and spatial gradients of VOCs relative to source proximity at the Barnett well pad, as well as operational changes at the DJB well pad. Though limited, these findings indicate that Methods 325A/B can be useful in application to characterize VOCs at well pad boundaries.

A Mobile Sensing Approach for Regional Surveillance of Fugitive Methane Emissions in Oil and Gas Production.

This paper addresses the need for surveillance of fugitive methane emissions over broad geographical regions. Most existing techniques suffer from being either extensive (but qualitative) or quantitative (but intensive with poor scalability). A total of two novel advancements are made here. First, a recursive Bayesian method is presented for probabilistically characterizing fugitive point-sources from mobile sensor data. This approach is made possible by a new cross-plume integrated dispersion formulation that overcomes much of the need for time-averaging concentration data. The method is tested here against a limited data set of controlled methane release and shown to perform well. We then present an information-theoretic approach to plan the paths of the sensor-equipped vehicle, where the path is chosen so as to maximize expected reduction in integrated target source rate uncertainty in the region, subject to given starting and ending positions and prevailing meteorological conditions. The information-driven sensor path planning algorithm is tested and shown to provide robust results across a wide range of conditions. An overall system concept is presented for optionally piggybacking of these techniques onto normal industry maintenance operations using sensor-equipped work trucks.

South Philadelphia passive sampler and sensor study.

From June 2013 to March 2015, in total 41 passive sampler deployments of 2 wk duration each were conducted at 17 sites in South Philadelphia, PA, with results for benzene discussed here. Complementary time-resolved measurements with lower cost prototype fenceline sensors and an open-path ultraviolet differential optical absorption spectrometer were also conducted. Minimum passive sampler benzene concentrations for each sampling period ranged from 0.08 ppbv to 0.65 ppbv, with a mean of 0.25 ppbv, and were negatively correlated with ambient temperature (-0.01 ppbv/°C, R2 = 0.68). Co-deployed duplicate passive sampler pairs (N = 609) demonstrated good precision with an average and maximum percent difference of 1.5% and 34%, respectively. A group of passive samplers located within 50 m of a refinery fenceline had a study mean benzene concentration of 1.22 ppbv, whereas a group of samplers located in communities >1 km distant from facilities had a mean of 0.29 ppbv. The difference in the means of these groups was statistically significant at the 95% confidence level (p < 0.001). A decreasing gradient in benzene concentrations moving away from the facilities was observed, as was a significant period-to-period variation. The highest recorded 2-wk average benzene concentration for the fenceline group was 3.11 ppbv. During this period, time-resolved data from the prototype sensors and the open-path spectrometer detected a benzene signal from the west on one day in particular, with the highest 5-min path-averaged benzene concentration measured at 24 ppbv. IMPLICATIONS: Using a variation of EPA's passive sampler refinery fenceline monitoring method, coupled with time-resolved measurements, a multiyear study in South Philadelphia informed benzene concentrations near facilities and in communities. The combination of measurement strategies can assist facilities in identification and mitigation of emissions from fugitive sources and improve information on air quality complex air sheds.

Assessment of volatile organic compound and hazardous air pollutant emissions from oil and natural gas well pads using mobile remote and on-site direct measurements.

UNLABELLED: Emissions of volatile organic compounds (VOCs) and hazardous air pollutants (HAPs) from oil and natural gas production were investigated using direct measurements of component-level emissions on pads in the Denver-Julesburg (DJ) Basin and remote measurements of production pad-level emissions in the Barnett, DJ, and Pinedale basins. Results from the 2011 DJ on-site study indicate that emissions from condensate storage tanks are highly variable and can be an important source of VOCs and HAPs, even when control measures are present. Comparison of the measured condensate tank emissions with potentially emitted concentrations modeled using E&P TANKS (American Petroleum Institute [API] Publication 4697) suggested that some of the tanks were likely effectively controlled (emissions less than 95% of potential), whereas others were not. Results also indicate that the use of a commercial high-volume sampler (HVS) without corresponding canister measurements may result in severe underestimates of emissions from condensate tanks. Instantaneous VOC and HAP emissions measured on-site on controlled systems in the DJ Basin were significantly higher than VOC and HAP emission results from the study conducted by Eastern Research Group (ERG) for the City of Fort Worth (2011) using the same method in the Barnett on pads with low or no condensate production. The measured VOC emissions were either lower or not significantly different from the results of studies of uncontrolled emissions from condensate tanks measured by routing all emissions through a single port monitored by a flow measurement device for 24 hr. VOC and HAP concentrations measured remotely using the U.S. Environmental Protection Agency (EPA) Other Test Method (OTM) 33A in the DJ Basin were not significantly different from the on-site measurements, although significant differences between basins were observed. IMPLICATIONS: VOC and HAP emissions from upstream production operations are important due to their potential impact on regional ozone levels and proximate populations. This study provides information on the sources and variability of VOC and HAP emissions from production pads as well as a comparison between different measurement techniques and laboratory analysis protocols. On-site and remote measurements of VOC and HAP emissions from oil and gas production pads indicate that measurable emissions can occur despite the presence of control measures, often as a result of leaking thief hatch seals on condensate tanks. Furthermore, results from the remote measurement method OTM 33A indicate that it can be used effectively as an inspection technique for identifying oil and gas well pads with large fugitive emissions.

Assessment of methane emissions from oil and gas production pads using mobile measurements.

A new mobile methane emissions inspection approach, Other Test Method (OTM) 33A, was used to quantify short-term emission rates from 210 oil and gas production pads during eight two-week field studies in Texas, Colorado, and Wyoming from 2010 to 2013. Emission rates were log-normally distributed with geometric means and 95% confidence intervals (CIs) of 0.33 (0.23, 0.48), 0.14 (0.11, 0.19), and 0.59 (0.47, 0.74) g/s in the Barnett, Denver-Julesburg, and Pinedale basins, respectively. This study focused on sites with emission rates above 0.01 g/s and included short-term (i.e., condensate tank flashing) and maintenance-related emissions. The results fell within the upper ranges of the distributions observed in recent onsite direct measurement studies. Considering data across all basins, a multivariate linear regression was used to assess the relationship of methane emissions to well age, gas production, and hydrocarbon liquids (oil or condensate) production. Methane emissions were positively correlated with gas production, but only approximately 10% of the variation in emission rates was explained by variation in production levels. The weak correlation between emission and production rates may indicate that maintenance-related stochastic variables and design of production and control equipment are factors determining emissions.

The changing paradigm of air pollution monitoring.

The air pollution monitoring paradigm is rapidly changing due to recent advances in (1) the development of portable, lower-cost air pollution sensors reporting data in near-real time at a high-time resolution, (2) increased computational and visualization capabilities, and (3) wireless communication/infrastructure. It is possible that these advances can support traditional air quality monitoring by supplementing ambient air monitoring and enhancing compliance monitoring. Sensors are beginning to provide individuals and communities the tools needed to understand their environmental exposures with these data individual and community-based strategies can be developed to reduce pollution exposure as well as understand linkages to health indicators. Each of these areas as well as corresponding challenges (e.g., quality of data) and potential opportunities associated with development and implementation of air pollution sensors are discussed.

Near-road multipollutant profiles: associations between volatile organic compounds and a tracer gas surrogate near a busy highway.

This research characterizes associations between multiple pollutants in the near-road environment attributed to a roadway line source. It also examines the use of a tracer gas as a surrogate of mobile source pollutants. Air samples were collected in summa canisters along a 300 m transect normal to a highway in Raleigh, North Carolina for five sampling periods spanning four days. Samples were subsequently measured for volatile organic compounds (VOCs) using an electron capture gas chromatograph. Sulfur hexafluoride (SF6) was released from a finite line source adjacent to the roadway for two of the sampling periods, collected in the canisters and measured with the VOCs. Associations between each VOC, and between VOCs and the tracer, were quantified with Pearson correlation coefficients to assess the consistency of the multi-pollutant dispersion profiles, and assess the tracer as a potential surrogate for mobile source pollutants. As expected, benzene, toluene, ethylbenzene, and m,p- and o-xylenes (collectively, BTEX) show strong correlations between each other; further BTEX shows a strong correlation to SF6. Between 26 VOCs, correlation coefficients were greater than 0.8, and 14 VOCs had coefficients greater than 0.6 with the tracer gas. Even under non-downwind conditions, chemical concentrations had significant correlations with distance. Results indicate that certain VOCs are representative of a larger multi-pollutant mixture, and many VOCs are well-correlated with the tracer gas.

Facility fence-line monitoring using passive samplers.

In 2009, the U.S. Environmental Protection Agency (EPA) executed a year-long field study at a refinery in Corpus Christi, TX, to evaluate the use of passive diffusive sampling technology for assessing time-averaged benzene concentrations at the facility fence line. The purpose of the study was to investigate the implementation viability and performance of this type of monitoring in a real-world setting as part of EPA's fence-line measurement research program. The study utilized 14-day, time-integrated Carbopack X samplers deployed at 18 locations on the fence line and at two nearby air monitoring sites equipped with automated gas chromatographs. The average fence-line benzene concentration during the study was 1075 parts per trillion by volume (pptv) with a standard deviation of 1935 pptv. For a 6-month period during which wind direction was uniform, the mean concentration value for a group of downwind sites exceeded the mean value of a similar upwind group by 1710 pptv. Mean value differences for these groups were not statistically significant for the remaining 6-month time period when wind directions were mixed. The passive sampling approach exhibited acceptable performance with a data completeness value of 97.1% (n = 579). Benzene concentration comparisons with automated gas chromatographs yielded an r2 value of 0.86 and a slope of 0.90 (n = 50). A linear regression of duplicate pairs yielded an r2 of 0.97, unity slope, and zero intercept (n = 56). In addition to descriptions of technique performance and general results, time-series analyses are described, providing insight into the utility of 2-week sampling for source apportionment under differing meteorological conditions. The limitations of the approach and recommendations for future measurement method development work are also discussed.