The effect of polymer solubilizing side-chains on solar cell stability.

The impact of side-chain variations on the photothermal stability of solar cells containing poly(benzodithiophene-diketopyrrolopyrrole) polymers are investigated in the absence of oxygen. Four different side-chains of benzodithiophene (BDT) are synthesized and copolymerized with diketopyrrolopyrrole (DPP) by Stille polymerization. The photothermal stability is measured as active layer blends with phenyl-C61-butyric acid methyl ester (PCBM) in encapsulated inverted photovoltaic cell architecture with zinc oxide and PEDOT: PSS as transport layers (ITO/ZnO/active layer/ PEDOT: PSS/Ag). Device degradation is correlated to the morphological behavior of the polymer:blend upon AM1.5 illumination (UV-visible light, 50 °C) and have been investigated by AFM, XRD, and UV-Vis. Once exposed to the light and to the temperature the BHJ stability is governed by two processes (i) PCBM crystallization and (ii) PCBM dimerization. Dimerization results in a rapid initial performance decrease followed by a more gradual decrease caused by a slower thermally activated crystallization. Depending on the blend morphology, dictated by the polymer's alkyl chain, the two processes occur to different extents thereby modulating the BHJ stability. Thus, of the polymer side-chains explored, linear alkyl side-chains stabilized the bulk heterojunction most effectively followed by no side-chain, alkoxy and branched side-chains. Lowering the concentration of fullerene in the active layer also reduces the rate of degradation across the polymers tested. This is a result of both the rate of crystallization and dimerization of fullerene being dependent on its concentration and the nature of the polymer side-chains. This approach appears to be a general strategy to increase the polymer:PCBM stability.

Computational investigation of hole mobilities in organic semiconductors: comparison of single crystal structures and surface adsorbed clusters.

We report hole mobilities obtained computationally based on both single crystal geometries and those obtained from crystal fragments optimised on a model surface. Such computational estimates can differ considerably from experimentally measured thin film mobilities. One source of this discrepancy is due to a difference in the morphology of the thin film compared with that of the crystal. Here, predictions of thin film hole mobilities based on optimised structures are given. A model surface is used to provide an inert geometric platform for the formation of an organic monolayer. The model is tested on pentacene and TIPS-pentacene for which experimental information of the surface morphology exists. The model has also been applied to four previously uninvestigated structures. Two of the compounds studied had fairly low predicted mobilities in their single crystal structures, which were vastly improved post-optimisation. This is in accord with experiment.

Influence of charge carrier mobility and morphology on solar cell parameters in devices of mono- and bis-fullerene adducts.

Herein, we analyze charge carrier mobility and morphology of the active blend layer in thin film organic solar cells and correlate them with device parameters. A low band gap donor-acceptor copolymer in combination with phenyl-C61-butyric acid methyl ester (PCBM) or two bis-adduct fullerenes, bis-PCBM and bis-o-quino-dimethane C60 (bis-oQDMC), is investigated. We study the charge transport of polymer:fullerene blends in hole- and electron-only devices using the space-charge limited current method. Lower electron mobilities are observed in both bis-adduct fullerene blends. Hole mobility, however, is decreased only in the blend containing bis-oQDMC. Both bis-adduct fullerene blends show very high open circuit voltage in solar cell devices, but poor photocurrent compared to the standard PCBM blend for an active layer thickness of 200 nm. Therefore, a higher short circuit current is feasible for the polymer:bis-PCBM blend by reducing the active layer thickness in order to compensate for the low electron mobility, which results in a PCE of 4.3%. For the polymer:bis-oQDMC blend, no such improvement is achieved due to an unfavorable morphology in this particular blend system. The results are supported by external quantum efficiency measurements, atomic force microscopy, transmission electron microscopy and UV/vis spectroscopy. Based on these results, the investigations presented herein give a more scientific basis for the optimization of solar cells.

Organic field-effect transistors of poly(2,5-bis(3-dodecylthiophen-2-yl)thieno[2,3-b]thiophene) deposited on five different silane self-assembled monolayers.

Depositing a fused-ring thieno-thiophene polymer on different self-assembled monolayers indicates that varying the SAM surface energy changes the FET mobility and turn-on voltage by varying polymer crystallinity at the buried interface.

Designing solution-processable air-stable liquid crystalline crosslinkable semiconductors.

Organic electronics technology, in which at least the semiconducting component of the integrated circuit is an organic material, offers the potential for fabrication of electronic products by low-cost printing technologies, such as ink jet, gravure offset lithography and flexography. The products will typically be of lower performance than those using the present state of the art single crystal or polysilicon transistors, but comparable to amorphous silicon. A range of prototypes are under development, including rollable electrophoretic displays, active matrix liquid crystal (LC) displays, flexible organic light emitting diode displays, low frequency radio frequency identification tag and other low performance electronics. Organic semiconductors that offer both electrical performance and stability with respect to storage and operation under ambient conditions are required. This work describes the development of reactive mesogen semiconductors, which form large crosslinked LC domains on polymerization within mesophases. These crosslinked domains offer mechanical stability and are inert to solvent exposure in further processing steps. Reactive mesogens containing conjugated aromatic cores, designed to facilitate charge transport and provide good oxidative stability, were prepared and their liquid crystalline properties evaluated. The organization and alignment of the mesogens, both before and after crosslinking, were probed by grazing incidence wide-angle X-ray scattering of thin films. Both time-of-flight and field effect transistor devices were prepared and their electrical characterization reported.

The acceptability and feasibility of the Positive Reinforcement Opportunity Project, a community-based contingency management methamphetamine treatment program for gay and bisexual men in San Francisco.

The Positive Reinforcement Opportunity Project (PROP) was a pilot program developed to build on the efficacy of contingency management (CM) using positive reinforcement to address the treatment needs of gay and bisexual men currently using crystal methamphetamines (meth). It was hypothesized that a version of CM could be implemented in San Francisco that was less costly than traditional treatment methods and reached gay and other MSM using meth who also engaged in high-risk sexual activity. Of the 178 men who participated in PROPfrom December 2003 to December 2005, many self-reported behaviors for acquiring and spreading sexually transmitted diseases including HIV infection. During the initial intake, 73% reported high-risk sexual behavior in the prior three months, with 60% reporting anal receptive and/or insertive sex without condoms. This report describes the implementation of PROP and suggest both its limitations and potential strengths. Initial findings suggest that PROP was a useful and low cost substance use treatment option that resulted in a 35% 90-day completion rate, which is similar to graduation rates from traditional, more costly treatment options. Further evaluation of the limited data from three- and six-month follow-up of those who completed PROP is currently ongoing.