Treatment of very large cranial defects with individually shaped polypropylene polyester knitwear prostheses: a series of 11 cases.

BACKGROUND: Very large cranial defects are not very common in neurosurgical practice and there is not any widely acknowledged standard of their treatment. One of the useful methods in such cases is individual forming of polypropylene-polyester knitwear. Such material was used in the past but before 2008 it was available only as standardized plates. Currently, it can be also produced as individually-shaped implants. The authors give their definition of very large cranial defects and present their experience with this cranioplastic method in such defects. METHODS: The authors collected data on 11 cases of patients with very large cranial defects, from a total of 156 cases, operated on in 5 Polish neurosurgical departments. The necessary implants were prepared for individual patients according to the data provided by a computed tomography examination and with the use of computer aided machining. RESULTS: All defects were larger than 120 cm2 (129 to 178 cm2) and exceeded 1/4 of the calvaria area. Patients were operated between 2008 to 2012. In all patients, a very good aesthetic result and correct skull reconstruction was achieved. The follow-up time in all cases exceeded 1 year and reached 4 years in one case. No complications were observed. CONCLUSIONS: Individually pre-shaped polypropylene-polyester knitwear prostheses are a good alternative to the existing cranioplasty methods, particularly in very large cranial defects.

Usefulness of computed tomography virtual bronchoscopy in the evaluation of bronchi divisions.

BACKGROUND: Since introduction of multislice CT scanners into clinical practice, virtual brochoscopy has gained a lot of quality and diagnostic potential. Nevertheless it does not have established place in diagnostics of tracheal and bronchi disorders and its potential has not been examined enough. Nowadays a majority of bronchial tree variants and lesions are revealed by bronchofiberoscopy, which is an objective and a relatively safe method, but has side effects, especially in higher-risk subjects. Therefore noninvasive techniques enabling evaluation of airways should be consistently developed and updated. MATERIAL/METHODS: Material consisted of 100 adults (45 female, 55 male) aged between 18 and 65 years (mean 40 years, median 40.5 years, SD 14.02), who underwent chest CT examination by means of a 16-slice scanner. Every patient had normal appearance of chest organs, with the exception of minor abnormalities that did not alter airways route. Divisions of bronchial tree to segmental level were evaluated and assigned to particular types by means of virtual bronchoscopy projection. In case of difficulties MPR or MinIP projection was used. RESULTS: THE FREQUENCY OF LOBAR BRONCHI DIVISIONS OTHER THAN THE TYPICAL ONES WAS IN: right upper lobar bronchi 45%, left 55%; middle lobar bronchi 21%, lingula 26%; right lower lobar bronchi 28%, left 29%. Subsuperior bronchus or bronchi were found on the right side in 44% and on the left side in 37%. No dependency between types of bronchial divisions on different levels was found.

Reconstruction of cranial defects with individually formed cranial prostheses made of polypropylene polyester knitwear: an analysis of 48 consecutive patients.

This article presents a new method of cranioplasty in which polypropylene polyester knitwear was used as the filling material. The basis for prosthesis shaping was a three-dimensional model of the defect made according to the patient's CT scans. Previously, such material has never been a subject of computer-aided design and computer-aided manufacturing (CAD/CAM) individual forming. The process of the prosthesis design included CT bone scans and mold preparation for each patient. Such prostheses were implanted in 48 patients with cranial defects. The total number of prostheses applied was 51. The follow-up time was at least 6 months up to 36 months. The group of treated patients is described here, and sample pictures are shown to illustrate the results. The smallest defect had a size of 15 cm(2); the biggest, 178 cm(2). The coverage and the aesthetic results were very good in all cases. Two patients had postoperative complications. The cranioplastic solution described here is a valuable addition to the existing reconstructive methods, because of the low cost of the implant, the ease of its adjustment to the shape of the defect, and the short time of preparation.

Polypropylene-polyester cranial prostheses prepared with CAD/CAM technology. Report of first 15 cases.

OBJECTIVES: The authors described a new cranioplastic method where polypropylene-polyester knitwear was shaped according to individual patient's skull 3D model. The material was formed in a customized manner and preoperatively adjusted to the patient needs with modern CAD/CAM techniques. PATIENTS AND METHODS: The procedure consisted of a CT scan with a simple but unorthodox protocol, 3D modeling of the bone defect and planned prosthesis, finally the preparation of the plate itself. Prostheses were used in the 15 cases of cranial defects. RESULTS: Sample cases were shown with preoperative and postoperative CT scans, patient pictures, and 3D models of the prostheses. The size of the defect ranged from 15 to 95 cm(2), and the observation period after the reconstructive operation ranged from 3 to 23 months. The results were very good in all cases of cranioplasties performed after craniectomies of various origins. CONCLUSION: CAD/CAM shaping gave better adjustment to requirements of specific defect than any standard preformed plate. Such method seemed to be a reasonable alternative to other cranioplastic solutions and can be recommended even for cases of large or complicated shape cranioplasties.