Non-Destructive Evaluation of Thermal Aging in EPDM Rubber Using Electromagnetic Techniques.

This study investigates the use of eddy-current technology and impedance spectroscopy in sensing the change in rubber properties after it is exposed to accelerated thermal aging. The thermal aging process, by application of temperature and pressure over time, of ethylene propylene diene monomer (EPDM) rubbers containing both carbon black (CB) and graphene are investigated. Both eddy-current sensing and electrical impedance measurement techniques were used for electromagnetic analysis. Both methods measure the in- and out-of-phase responses as a function of excitation frequency at room temperature. The measurements were performed before and after the aging process. The electrical percolation threshold was detected in the rubber samples by varying the CB content from 0 to 40 wt%. In the rubber sample containing 30 wt% CB, 0-5 wt% of the CB was replaced with graphene flakes. The substitution of graphene for CB in the EPDM rubber formulation provided an enhanced eddy-current and electrical impedance response. The findings demonstrate the feasibility of employing electromagnetic analysis techniques to investigate the extent of aging.

In situ polymerization of polyaniline in wood veneers.

The present study describes the possibility to polymerize aniline within wood veneers to obtain a semi-conducting material with solid wood acting as the base template. It was determined that it is possible to synthesize the intrinsically conductive polymer (ICP) polyaniline in situ within the wood structure of Southern yellow pine veneers, combining the strength of the natural wood structure with the conductivity of the impregnated polymer. It was found that polyaniline is uniformly dispersed within the wood structure by light microscopy and FT-IR imaging. A weight percent gain in the range of 3-12 wt % was obtained with a preferential formation in the wood structure and cell wall, rather than in the lumen. The modified wood was found to be less hydrophilic with the addition of phosphate doped polyaniline as observed by equilibrium water swelling studies. While wood itself is insulating, the modified veneers had conductivities of 1 × 10(-4) to 1 × 10(-9) S cm(-1), demonstrating the ability to tune the conductivity and allowing for materials with a wide range of applications, from anti-static to charge-dispersing materials. Furthermore, the modified veneers had lower total and peak heat releases, as determined by cone calorimetry, because of the char properties of the ICP. This is of interest if these materials are to be used in building and furniture applications where flame retardance is of importance.

Electron-beam-initiated polymerization of poly(ethylene glycol)-based wood impregnants.

The current study demonstrates that methacrylate and acrylate poly(ethylene glycol) (PEG) functional oligomers can be effectively impregnated into wood blocks, and cured efficiently to high conversions without catalyst by e-beam radiation, allowing for less susceptibility to leaching, and favorable properties including higher Brinell hardness values. PEG based monomers were chosen because there is a long history of this water-soluble monomer being able to penetrate the cell wall, thus bulking it and decreasing the uptake of water which further protects the wood from fungal attack. Diacrylate, dimethacrylate, and dihydroxyl functional PEG of M(w) 550-575, of concentrations 0, 30, 60, and 100 wt % in water, were vacuum pressure impregnated into Scots Pine blocks of 15 × 25 × 50 mm in an effort to bulk the cell wall. The samples were then irradiated and compared with nonirradiated samples. It was shown by IR, DSC that the acrylate polymers were fully cured to much higher conversions than can be reached with conventional methods. Leaching studies indicated a much lower amount of oligomer loss from the cured vinyl functional PEG chains in comparison to hydroxyl functional PEG indicating a high degree of fastening of the polymer in the wood. The Brinell hardness indicated a significant increase in hardness to hardwood levels in the modified samples compared to the samples of hydroxyl functional PEG and uncured vinyl PEG samples, which actually became softer than the untreated Scots Pine. By monitoring the dimensions of the sample it was found by weight percent gain calculations (WPG %) that water helps to swell the wood structure and allow better access of the oligomers into the cell wall. Further, the cure shrinkage of the wood samples demonstrated infiltration of the oligomers into the cell wall as this was not observed for methyl methacrylate which is well-documented to remain in the lumen. However, dimensional stability of the vinyl polymer modified blocks when placed in water was not observed to the same extent as PEG.

Enzymatic one-pot route to telechelic polypentadecalactone epoxide: synthesis, UV curing, and characterization.

In an enzymatic one-pot procedure immobilized lipase B from Candida antarctica was used to synthesize semicrystalline diepoxy functional macromonomers based on glycidol, pentadecalactone, and adipic acid. By changing the stoichiometry of the building blocks, macromonomers of controlled molecular weight from 1400 to 2700 g mol(-1) could be afforded. The enzyme-catalyzed reaction went to completion (conversion >or=95%) within 24 h at 60 degrees C. After removal of the enzyme, the produced macromonomers were used for photopolymerization without any purification. The macromonomers readily copolymerized cationically with a cycloaliphatic diepoxide (Cyracure UVR-6110; CA-dE) to high conversion. The cross-linked copolymers formed a durable film with a degree of crystallinity depending on the macromonomer size and amount of CA-dE used, without CA-dE the macromonomers homopolymerized only to a low degree. Combined with CA-dE conversions of 85-90% were determined by FT-Raman spectroscopy. The films became more durable once reinforced with CA-dE, increasing the cross-link density and reducing the crystallinity of the PDL segments in the films.

Delivery of itraconazole from extruded HPC films.

The treatment of onychomycosis by oral delivery is problematic due to the high concentrations required and if available, a topical transcuticular route would be preferred. Towards this end the hot-melt extruded hydroxypropylcellulose based films containing anti-fungal drug itraconazole and alpha-tocopherol topical treatment for onychomycosis were studied. DSC and X-ray measurements did not show a crystalline itraconazole phase indicating the drug is present in the amorphous state. The rate of itraconazole release trended directly with the degree of film hydration and inversely to the hydroxypropylcellulose molecular weight. This results from a higher degree of crystallinity of the HPC films which also changes the release kinetics from first order to zero order as a more tortuous path is created.