Damage-tolerant 3D-printed ceramics via conformal coating.

Ceramic materials, despite their high strength and modulus, are limited in many structural applications due to inherent brittleness and low toughness. Nevertheless, ceramic-based structures, in nature, overcome this limitation using bottom-up complex hierarchical assembly of hard ceramic and soft polymer, where ceramics are packaged with tiny fraction of polymers in an internalized fashion. Here, we propose a far simpler approach of entirely externalizing the soft phase via conformal polymer coating over architected ceramic structures, leading to damage tolerance. Architected structures are printed using silica-filled preceramic polymer, pyrolyzed to stabilize the ceramic scaffolds, and then dip-coated conformally with a thin, flexible epoxy polymer. The polymer-coated architected structures show multifold improvement in compressive strength and toughness while resisting catastrophic failure through a considerable delay of the damage propagation. This surface modification approach allows a simple strategy to build complex ceramic parts that are far more damage-tolerant than their traditional counterparts.

Superhydrophobic self-similar nonwoven-titanate nanostructured materials.

HYPOTHESIS: Self-similarity is a scale-invariant irregularity that can assist in designing a robust superhydrophobic material. A combinatorial design strategy involving self-similarity and dual-length scale can be employed to create a new library of a doubly re-entrant, disordered, and porous network of superhydrophobic materials. Asymmetric wettability can be engineered in nonwoven materials by rendering them with superhydrophobic characteristics on one side. EXPERIMENTS: A facile, scalable, and inexpensive spray-coating technique was used to decorate the weakly hydrophobicstearate-treatedtitanate nanowires (TiONWs)over the self-similar nonwoven material. Laser scanning confocal microscopy was employed to image the impalement dynamics in three dimensions. With the aid of X-ray microcomputed tomography analysis, the three-dimensional (3D) nonwoven structural parameters were obtained and analyzed. The underwater superhydrophobic behavior of the prepared samples was investigated. FINDINGS: A classic 'lotus effect' has been successfully endowed in self-similar nonwoven-titanate nanostructured materials (SS-Ti-NMs) from a nonwoven material that housed the air pockets in bulk and water repellent TiONWs on the surface. The finer fiber-based SS-Ti-NMs exhibited lower roll-off angles and a thinner layer of water on its surface. An asymmetric wettability and the unusual display of underwater superhydrophobic behavior of SS-Ti-NMs have been uncovered.

Stability of Boron Nitride Nanosphere Dispersions in the Presence of Polyelectrolytes.

Boron nitride nanospheres (BNNSs) were functionalized with polyelectrolytes. The effect of the polyelectrolyte dose and ionic strength on the charging and aggregation properties was investigated. At appropriate polyelectrolyte doses, charge neutralization occurred, whereas by increasing the dose, charge reversal was observed. The complete coating of the particles was indicated by a plateau in the ζ-potential values, which do not change significantly beyond the dose corresponding to the onset of such a plateau. The dispersions were highly aggregated around the charge neutralization point, while at lower or higher doses, the particles were stable. The salt-induced aggregation experiments revealed that the polyelectrolyte coatings contribute to the colloidal stability of the particles, namely, the critical coagulation concentrations deviated from the one determined for bare BNNSs. The presence of electrostatic and steric interparticle forces induced by the adsorbed polyelectrolyte chains was assumed. The obtained results confirm that the comprehensive investigation of the colloidal stability of BNNS particles is crucial to design stable or unstable dispersions and that polyelectrolytes are suitable agents for both stabilization and destabilization of BNNS dispersions, depending on the purpose of their application.

Specific Ion Effects on Aggregation and Charging Properties of Boron Nitride Nanospheres.

The charging and aggregation properties of boron nitride nanospheres (BNNSs) were investigated in the presence of electrolytes of different compositions and valences in aqueous suspensions. The influence of mono- and multivalent cations (counterions) and anions (coions) on the colloidal stability of the negatively charged particles was studied over a wide range of salt concentrations. For monovalent ions, similar trends were determined in the stability and charging of the particles irrespective of the salt composition, i.e., no ion-specific effects were observed. Once multivalent counterions were involved, the critical coagulation concentrations (CCCs) decreased with the valence in line with the direct Schulze-Hardy rule. The dependence indicated an intermediate charge density for BNNSs. The influence of the coions on the CCCs was weaker and the destabilization ability followed the inverse Schulze-Hardy rule. The predominant interparticle forces were identified as electrical double-layer repulsion and van der Waals attraction. These findings offer useful information to design stable BNNS dispersions in various applications, where mono- and multivalent electrolytes or their mixtures are present in the samples.

Fast optical method for characterizing plasmonic nanoparticle adhesion on functionalized surfaces.

In this paper, a rapid optical method for characterizing plasmonic (gold) nanoparticle (AuNP) adhesion is presented. Two different methods were used for AuNP preparation: the well-known Turkevich method resulted in particles with negative surface charge; for preparing AuNPs with positive surface charge, stainless steel was used as reducing agent. The solid surface for adhesion was provided by a column packed with pristine or surface-modified glass beads. The size of the nanoparticles was studied by transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS); the surface charge of the components was determined by streaming potential measurements. The characterization of adhesion was performed in a flow system by UV-Vis spectroscopy. During the adhesion experiments, the role of the surface charge, the particle size, and the pH were studied, as well as the adhered amount of gold nanoparticles and the surface coverage values. The latter was estimated by theoretical calculations and defined by the quotient of the measured and the maximal adhered amount of nanoparticles, which could be determined by the cross-sectional area of the NPs and the specific surface area of the glass beads. The results are verified by the polarization reflectometric interference spectroscopy (PRIfS) method: silica nanoparticles with diameters of a few hundred (d~450) nanometers were immobilized on the surface of glass substrate by the Langmuir-Blodgett method, the surface was modified similar to the 3D (continuous flow packed column) system, and gold nanoparticles from different pH solutions were adhered during the measurements. These kinds of modified surfaces allow the investigation of biomolecule adsorption in the same reflectometric setup. Graphical abstract.

Noble-Metal-Free Iron Nitride/Nitrogen-Doped Graphene Composite for the Oxygen Reduction Reaction.

Considerable effort has been devoted recently to replace platinum-based catalysts with their non-noble-metal counterparts in the oxygen reduction reaction (ORR) in fuel cells. Nitrogen-doped carbon structures emerged as possible candidates for this role, and their earth-abundant metal-decorated composites showed great promise. Here, we report on the simultaneous formation of nitrogen-doped graphene and iron nitride from the lyophilized mixture of graphene oxide and iron salt by high-temperature annealing in ammonia atmosphere. A mixture of FeN and Fe2N particles was formed with average particle size increasing from 23.4 to 127.0 nm and iron content ranging from 5 to 50 wt %. The electrocatalytic oxygen reduction activity was investigated via the rotating disk electrode method in alkaline media. The highest current density of 3.65 mA cm-2 at 1500 rpm rotation rate was achieved in the 20 wt % catalyst via the four-electrode reduction pathway, exceeding the activity of both the pristine iron nitride and the undecorated nitrogen-doped graphene. Since our catalysts showed improved methanol tolerance compared to the platinum-based ones, the formed non-noble-metal system offers a viable alternative to the platinum-decorated carbon black (Pt/CB) ORR catalysts in direct methanol fuel cells.