3D structure of the natural tetrameric form of human butyrylcholinesterase as revealed by cryoEM, SAXS and MD.

Human plasma butyrylcholinesterase (BChE) is an endogenous bioscavenger that hydrolyzes numerous medicamentous and poisonous esters and scavenges potent organophosphorus nerve agents. BChE is thus a marker for the diagnosis of OP poisoning. It is also considered a therapeutic target against Alzheimer's disease. Although the X-ray structure of a partially deglycosylated monomer of human BChE was solved 15 years ago, all attempts to determine the 3D structure of the natural full-length glycosylated tetrameric human BChE have been unsuccessful so far. Here, a combination of three complementary structural methods-single-particle cryo-electron microscopy, molecular dynamics and small-angle X-ray scattering-were implemented to elucidate the overall structural and spatial organization of the natural tetrameric human plasma BChE. A 7.6 ŠcryoEM map clearly shows the major features of the enzyme: a dimer of dimers with a nonplanar monomer arrangement, in which the interconnecting super helix complex PRAD-(WAT)4-peptide C-terminal tail is located in the center of the tetramer, nearly perpendicular to its plane, and is plunged deep between the four subunits. Molecular dynamics simulations allowed optimization of the geometry of the molecule and reconstruction of the structural features invisible in the cryoEM density, i.e., glycan chains and glycan interdimer contact areas, as well as intermonomer disulfide bridges at the C-terminal tail. Finally, SAXS data were used to confirm the consistency of the obtained model with the experimental data. The tetramer organization of BChE is unique in that the four subunits are joined at their C-termini through noncovalent contacts with a short polyproline-rich peptide. This tetramer structure could serve as a model for the design of highly stable glycosylated tetramers.

Controlling the phase transition in nanocrystalline ferroelectric thin films via cation ratio.

Traditionally, the ferroelectric Curie temperature can be manipulated by chemical substitution, e.g., in Ba1-xSrxTiO3 as one of the archetypical representatives. Here, we show a novel approach to tune the ferroelectric phase transition applicable for nanostructured thin films. We demonstrate this effect in nano-grained BaTiO3 films. Based on an enhanced metastable cation solubility with Ba/Ti-ratios of 0.8 to 1.06, a significant shift of the phase transition temperature is discovered. The transition temperature increases linearly from 212 K to 350 K with increasing Ba/Ti ratio. For all Ba/Ti ratios, a completely diffused phase transition is present resulting in a negligible temperature sensitivity of the dielectric constant. Schottky defects are identified as the driving force behind the off-stoichiometry and the shift of the phase transition temperature as they locally induce lattice strain. Complementary temperature dependent Raman experiments reveal the presence of the hexagonal polymorph in addition to the perovskite phase in all cases. Interestingly, the hexagonal BaTiO3 influences the structural transformation on the Ba-rich side, while on the Ti-rich side no changes for the hexagonal polymorph at the ferroelectric transition temperature are observed. This concerted structural change of both polymorphs on the Ba-rich side causes a broad phase transition region spanning over a wide range up to 420 K including the transition temperature of 350 K obtained from dielectric measurements. These findings are promising for fine adjustment of the phase transition temperature and low temperature coefficient of permittivity.

Halloysite nanotubule clay for efficient water purification.

Halloysite clay has chemical structure similar to kaolinite but it is rolled in tubes with diameter of 50 nm and length of ca. 1000 nm. Halloysite exhibits higher adsorption capacity for both cationic and anionic dyes because it has negative SiO2 outermost and positive Al2O3 inner lumen surface; therefore, these clay nanotubes have efficient bivalent adsorbancy. An adsorption study using cationic Rhodamine 6G and anionic Chrome azurol S has shown approximately two times better dye removal for halloysite as compared to kaolin. Halloysite filters have been effectively regenerated up to 50 times by burning the adsorbed dyes. Overall removal efficiency of anionic Chrome azurol S exceeded 99.9% for 5th regeneration cycle of halloysite. Chrome azurol S adsorption capacity decreases with the increase of ionic strength, temperature and pH. For cationic Rhodamine 6G, higher ionic strength, temperature and initial solution concentration were favorable to enhanced adsorption with optimal pH 8. The equilibrium adsorption data were described by Langmuir and Freundlich isotherms.

Interfacial modification of clay nanotubes for the sustained release of corrosion inhibitors.

Long-lasting anticorrosive coatings for steel have been developed on the basis of halloysite nanotubes loaded with three corrosion inhibitors: benzotriazole, mercaptobenzothiazole, and mercaptobenzimidazole. The inhibitors' loaded tubes were admixed at 5-10 wt % to oil-based alkyd paint providing sustained agent release and corrosion healing in the coating defects. The slow 20-30 h release of the inhibitors at defect points caused a remarkable improvement in the anticorrosion efficiency of the coatings. Further time expansion of anticorrosion agent release has been achieved by the formation of release stoppers at nanotube ends with urea-formaldehyde copolymer and copper-inhibitor complexation. The corrosion protection efficiency was tested on ASTM A366 steel plates in a 0.5 M NaCl solution with the microscanning of corrosion current development by microscopy inspection and studying paint adhesion. The best protection was found using halloysite/mercaptobenzimidazole and benzotriazole inhibitors. Stopper formation with urea-formaldehyde copolymer provided an additional increase in corrosion efficiency as a result of the longer release of inhibitors.