Nature of fiber-coupled detector responsivity measurements at 0.1% using a primary standard.

We demonstrate the capability to measure the absolute power responsivity of optical fiber-coupled detectors at an expanded uncertainty of 0.1%, by direct comparison with a cryogenic primary standard. To facilitate synchronous power measurements, commercial all-fiber beam-splitters direct laser diode light simultaneously to the device under test and the primary standard. We investigate the use of single-mode, polarisation maintaining, and photonic crystal fibers to access the cryogenic standard, and report a reduction in the temperature dependent effective refractive index of these fibers of 0.1%, 0.15% and 0.3% respectively in going from room temperature to 5 K. We also evaluate the polarisation dependent loss of the beam-splitters, the stability of the beam-splitter ratio between the cryogenic detector and the device under test and the temporal and modal stability of the Fabry-Pérot laser diode sources. It is shown that the stability of the optical fiber beam-splitters limits the overall performance of the measurement system to an expanded uncertainty of 0.1%.

Verification of calibration methods for determining photon-counting detection efficiency using superconducting nano-wire single photon detectors.

In recent years several ways to radiometrically calibrate optical fiber-coupled detectors have been developed. However, fiber-coupled calibration methods for single photon detectors have not been compared by national metrology institutes in order to validate their equivalence or traceability to the international systems of units yet.. Here, we present the comparison of radiometric calibration methods traceable to a NIST cryogenic radiometer at the 'few-photon' level. The calibration methods are based on metrology grade optical power meters. The expanded (k = 2) relative standard uncertainties of the calibration methods for the detection efficiency are of the order of 0.5%. However, the results changed relatively by 10% with a different set of optical fibers and mating connectors. These results stress the importance of fiber-core dimensions and fiber-connector repeatability.

High-efficiency superconducting nanowire single-photon detectors fabricated from MoSi thin-films.

We report on MoSi SNSPDs which achieved high system detection efficiency (87.1 ± 0.5% at 1542 nm) at 0.7 K and we demonstrate that these detectors can also be operated with saturated internal efficiency at a temperature of 2.3 K in a Gifford-McMahon cryocooler. We measured a minimum system jitter of 76 ps, maximum count rate approaching 10 MHz, and polarization dependence as low as 3.3 ± 0.1%. The performance of MoSi SNSPDs at 2.3 K is similar to the performance of WSi SNSPDs at < 1 K. The higher operating temperature of MoSi SNSPDs makes these devices promising for widespread use due to the simpler and less expensive cryogenics required for their operation.

Optical-Fiber Power Meter Comparison between NIST and KRISS.

We describe the results of a comparison of reference standards between the National Institute of Standards and Technology (NIST-USA) and Korea Research Institute of Standards and Science (KRISS-R.O. Korea) for optical fiber-based power measurements at wavelengths of 1302 nm and 1546 nm. We compare the laboratories' reference standards by means of a temperature-controlled optical trap detector. Measurement results showed the largest difference of less than 2.5 parts in 10(3), which is within the combined standard (k=1) uncertainty for the two laboratories' reference standards.

Optical high-power nonlinearity comparison between the National Institute of Standards and Technology and the National Metrology Institute of Japan at 1480 nm.

We compare the results of measurements of the nonlinearity of high-power optical fiber powermeters (OFPMs) by two national metrology institutes (NMIs): the National Institute of Standards and Technology (NIST-USA) and the National Metrology Institute of Japan/National Institute of Advanced Industrial Science and Technology (NMIJ/AIST-Japan) at a wavelength of 1480 nm. The nonlinearity and range discontinuity of a commercial OFPM were measured from 1 mW to 500 mW by use of a superposition method (both laboratories) and from 1 mW to 250 mW by use of a comparison method (NMIJ only). Measurement results showed largest differences of less than 1.6 parts in 10(3), which is within the combined expanded (k = 2) uncertainty for both laboratories.

Optical Fiber Power Meter Comparison Between NIST and NIM.

We describe the results of a comparison of reference standards between the National Institute of Standards and Technology (NIST-USA) and National Institute of Metrology (NIM-China). We report optical fiber-based power measurements at nominal wavelengths of 1310 nm and 1550 nm. We compare the laboratories' reference standards by means of a commercial optical power meter. Measurement results showed the largest difference of less than 2.6 parts in 10(3), which is within the combined standard (k = 1) uncertainty for the laboratories' reference standards.

Bilateral Optical Power Meter Comparison Between NIST and CENAM.

We describe the results of a comparison of reference standards between the National Institute of Standards and Technology (NIST-USA) and Centro Nacional De Metrología (CENAM-Mexico). Open beam (free field) and optical-fiber-based measurements at wavelengths of 1302 nm and 1546 nm are reported. Both laboratories' reference standards were compared by means of a temperature-controlled optical trap detector. Measurements showed a largest difference of less than 3.4 parts in 10(3), which is within the combined expanded (k = 2) uncertainty for the laboratories' reference standards.

Trilateral optical powermeter comparison between NIST, NMIJ/AIST, and METAS.

We describe the results of a comparison of reference standards between three National Metrology Institutes: the National Institute of Standards and Technology (NIST, USA), the National Metrology Institute of Japan/National Institute of Advanced Industrial Science and Technology (NMIJ/AIST, Japan), and the Federal Office of Metrology (METAS, Switzerland). Open-beam- (free field) and optical-fiber-based measurements at wavelengths of 1302 and 1546 nm are reported. Three laboratories' reference standards are compared by means of two temperature-controlled, optical trap detectors. Measurement results show the largest differences of less than 4.2 parts in 10(3), which is within the expanded (k=2) uncertainty for the laboratories' reference standards.

Optical-Fiber Power Meter Comparison Between NIST and PTB.

We describe the results of a comparison of reference standards between the National Institute of Standards and Technology (NIST-USA) and Physikalisch-Technische Bundesanstalt (PTB-Germany) at nominal wavelengths of 1300 nm and 1550 nm using an optical-fiber cable. Both laboratories used thermal detectors as reference standards. A novel temperature-controlled, optical-trap detector was used as a transfer standard to compare two reference standards. Measurement results showed differences of less than 1.5 × 10(-3), which is within the combined uncertainty for both laboratories.

Transfer function approach to the experimental determination of mode transfer matrices.

An improved scheme for characterization of multimode fiber systems is investigated. Characterization with transfer matrices requires multiple measurements for each component. The transfer function approach herein investigated requires only a single launch measurement to be made on a component, which afterward can be described by as few as two numbers. Further, it is shown that this technique is considerably more accurate and repeatable than matrix approaches. A concatenation experiment is performed to demonstrate the efficacy of the new technique as well as to compare it with the more traditional transfer matrix approach.

Transfer function analysis of measured transfer matrices.

Measurements of mode transfer matrices of various multimode fiber optic connectors are presented. To analyze the accuracy and repeatability of such measurements, a theoretical framework which employs mode transmission functions is derived. It is shown that the transfer function can be used to find transfer matrices for any set of launches. A procedure for determination of the mode transfer function is given.