In-Situ surface enhanced infrared absorption spectroscopy study of electrocatalytic oxidation of ethanol on Platinum/Gold surface.

The behavior of ethanol oxidation reaction on composite electrodes prepared by deposition platinum on a gold surface (Pt/Au) were studied by cyclic voltammetry and surface enhanced infrared absorption spectroscopy (SEIRAS) analysis. The results show that the Pt electrode has high oxidation activity and significant poison behavior; on the contrary, the Au electrode demonstrates low activity without a poison peak. The SEIRAS analyses reveal that both carbon monoxide (CO) and carbon dioxide (CO2) appear during anode sweeping, and the CO peak density decreases with increasing potential and finally is eliminated. During the cathodic scanning, the CO peak reappears, and the peak intensity increases with scanning cycles, demonstrating a high poison behavior and the C1 reaction route on Pt. On the Au electrode, CO2 and CO peaks were not observed; instead, an acetic acid peak appeared, indicating a C2 reaction path. For the Pt/Au composited electrodes, the electrochemical activities of the electrodes, as well as their poison behavior, increased with the deposition amount of Pt. However, the intensities of the poison peaks are smaller than those of oxidation ones; therefore, a higher tolerance to the CO poison can be achieved. For the 2 m-Pt/Au composite electrode, the activity is close to that of pure Pt, but the poison tolerance is 3 times the value of Pt.

Highly Efficient Dye-sensitized Solar Cells Based on Poly(vinylidene fluoride-co-hexafluoropropylene) and Montmorillonite Nanofiller-based Composite Electrolytes.

Highly efficient nanocomposite electrolytes were prepared by mixing the montmorillonite (MMT) clay nanofillers and iodide poly(vinylidene fluoride-co-hexafluoropropylene (PVDF-HFP) gel electrolytes for the purpose of measuring the performance of quasi-solid-state dye-sensitized solar cells (QS-DSSCs). The impacts of different amounts of MMT nanofillers on the ion diffusivity, conductivity of the polymer gel electrolytes (PGEs), and the photovoltaic performance of the cells using the PGEs were evaluated. The results indicated that the use of 5 wt.% MMT markedly increase the ion diffusivity and conductivity of the PVDF-HFP PGE. The introduction of 5 wt.% nanofillers considerably reduced the Warburg diffusion resistance, which made to the high performance of the QS-DSSCs. Cells utilizing 5 wt.% MMT nanofillers were shown to obtain a power conversion efficiency (PCE) (6.77%) higher than that obtained for cells using pure PGEs and identical to that obtained using liquid electrolytes (LEs) (6.77%). The high PCE was a result of an enhance in the current density in the presence of the 5 wt.% MMT nanofillers. The DSSC efficiency was found to maintain 99.9% of its initial value after 194 h of testing at 60℃ under dark environments. The stability of the DSSC using PGEs with the optimal amount of MMT nanofillers was higher than that for the cells using liquid electrolyte and pure PGE.

High-Efficiency Bifacial Dye-Sensitized Solar Cells for Application under Indoor Light Conditions.

High-efficiency, stable bifacial dye-sensitized solar cells (DSSCs) are prepared for application under indoor light conditions. A 3-methoxypropionitrile solvent and cobalt redox couples are utilized to prepare the electrolytes. To obtain the best cell performance, the components of the DSSCs, including electrolytes, photoanodes, and counter electrodes (CEs), are regulated. The experimental results indicate that an electrolyte comprising a Co (II/III) ratio of 0.11/0.025 M, 1.2 M 4-tert-butylpyridine, Y123 dye, a CE with the platinum (Pt) layer thickness of 0.16 nm, and a photoanode with titanium dioxide (TiO2) layer thickness of 10 µm (6 µm main layer and 4 µm scattering layer) are the best conditions under which to achieve a high power conversion efficiency. It is also found that the best cells have high recombination resistance at the photoelectrode/electrolyte interface and low charge transfer resistance at the counter electrode/electrolyte interface, which contributes to, respectively, the high current density and open-circuit voltage of the corresponding cells. This DSSC can achieve efficiencies of 22.66%, 23.48%, and 24.52%, respectively, under T5 light illumination of 201.8, 607.8, and 999.6 lx. For fabrication of bifacial DSSCs with a semitransparent property, photoanodes without the TiO2 scattering layer, as well as an ultrathin Pt film, are utilized. The thicknesses of the TiO2 main layer and Pt film are reregulated. This shows that a Pt film with 0.55 nm thickness has both high transmittance (76.01%) and catalytic activity. By using an 8 µm TiO2 main layer, optimal cell efficiencies of 20.65% and 17.31% can be achieved, respectively, for the front-side and back-side illuminations of 200 lx T5 light. The cells are highly stable during a long-term performance test at both 35 and 50 °C.

Graphene Oxide Sponge as Nanofillers in Printable Electrolytes in High-Performance Quasi-Solid-State Dye-Sensitized Solar Cells.

A graphene oxide sponge (GOS) is utilized for the first time as a nanofiller (NF) in printable electrolytes (PEs) based on poly(ethylene oxide) and poly(vinylidene fluoride) for quasi-solid-state dye-sensitized solar cells (QS-DSSCs). The effects of the various concentrations of GOS NFs on the ion diffusivity and conductivity of electrolytes and the performance of the QS-DSSCs are studied. The results show that the presence of GOS NFs significantly increases the diffusivity and conductivity of the PEs. The introduction of 1.5 wt % of GOS NFs decreases the charge-transfer resistance at the Pt-counter electrode/electrolyte interface ( Rpt) and increases the recombination resistance at the photoelectrode/electrolyte interface ( Rct). QS-DSSC utilizing 1.5 wt % GOS NFs can achieve an energy conversion efficiency (8.78%) higher than that found for their liquid counterpart and other reported polymer gel electrolytes/GO NFs based DSSCs. The high energy conversion efficiency is a consequence of the increase in both the open-circuit potential ( Voc) and fill factor with a slight decrease in current density ( Jsc). The cell efficiency can retain 86% of its initial value after a 500 h stability test at 60 °C under dark conditions. The long-term stability of the QS-DSSC with GOS NFs is higher than that without NFs. This result indicates that the GOS NFs do not cause dye-desorption from the photoanode in a long-term stability test, which infers a superior performance of GOS NFs as compared to TiO2 NFs in terms of increasing the efficiency and long-term stability of QS-DSSCs.

Effects of TiO2 and TiC Nanofillers on the Performance of Dye Sensitized Solar Cells Based on the Polymer Gel Electrolyte of a Cobalt Redox System.

Polymer gel electrolytes (PGEs) of cobalt redox system are prepared for dye sensitized solar cell (DSSC) applications. Poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) is used as a gelator of an acetonitrile (ACN) liquid electrolyte containing tris(2,2'-bipyridine)cobalt(II/III) redox couple. Titanium dioxide (TiO2) and titanium carbide (TiC) nanoparticles are utilized as nanofillers (NFs) of this PGE, and the effects of the two NFs on the conductivity of the PGEs, charge-transfer resistances at the electrode/PGE interface, and the performance of the gel-state DSSCs are studied and compared. The results show that the presence of TiC NFs significantly increases the conductivity of the PGE and decreases the charge-transfer resistance at the Pt counter-electrode (CE)/PGE interface. Therefore, the gel-state DSSC utilizing TiC NFs can achieve a conversion efficiency (6.29%) comparable to its liquid counterpart (6.30%), and, furthermore, the cell efficiency can retain 94% of its initial value after a 1000 h stability test at 50 °C. On the contrary, introduction of TiO2 NFs in the PGE causes a decrease of cell performances. It shows that the presence of TiO2 NFs increases the charge-transfer resistance at the Pt CE/PGE interface, induces the charge recombination at the photoanode/PGE interface, and, furthermore, causes a dye desorption in a long-term-stability test. These results are different from those reported for the iodide redox system and are ascribed to a specific attractive interaction between TiO2 and cobalt redox ions.

Room temperature aerobic oxidation of amines by a nanocrystalline ruthenium oxide pyrochlore nafion composite catalyst.

The aerobic oxidation of primary amines to their respective nitriles has been carried out at room temperature using a highly reusable nanocrystalline ruthenium oxide pyrochlore Nafion composite catalyst (see figure).

Flavonoids from Andrographis viscosula.

Phytochemical investigation of the whole plant of Andrographis viscosula has led to the isolation of three new 2'-oxygenated flavonoids, (2R)-5-hydroxy-7,2',3'-trimethoxyflavanone (1), 7,2',5'-trimethoxyflavone (2), 5,7,2',3'-tetramethoxyflavone (3), and eight known flavones, 5,7,2'-trimethoxyflavone (4), 5,7,2',4',5'-pentamethoxyflavone (5), echioidinin (6), 5,2',6'-trihydroxy-7-methoxyflavone (7), 5-hydroxy-7,2'-dimethoxyflavone (8), echioidin (9), echioidinin 5-O-glucoside (10), and 5,2',6'-trihydroxy-7-methoxyflavone 2'-O-glucoside (11). The structures of 1-11 were elucidated by physical and spectral methods, including extensive 2D NMR studies. The presence of 2'-oxygenated flavonoids is apparently restricted to Andrographis species in Acanthaceae. Therefore, 2'-oxygenated flavonoids are regarded as chemotaxonomic markers of Andrographis genus in the Acanthaceae family.