A rapid and green GC-MS method for the sampling of volatile organic compounds in spices and flowers by concurrent headspace single-drop microextraction and solid-phase microextraction.

The equilibrium rather than the exhaustive nature of headspace single-drop microextraction (HS-SDME) and headspace solid-phase microextraction (HS-SPME) allowed the concurrent sampling of volatile organic compounds (VOCs) on the same sample in the same vial in a dual extraction configuration. This has avoided the necessity of conducting a separate set of experiments and was found to produce results in the time duration of a single sample preparation experiment. The results obtained by HS-SDME were validated against those found by the standard method of HS-SPME. Rectilinear calibration was made for certain VOCs tested as analytes over the range of 0.01-8 µg g-1, and the average values of R2, LOD and LOQ were found to be, respectively, 0.9992, 1.9 ng g-1 and 5.7 ng g-1 in HS-SDME, and 0.9991, 3.1 ng g-1 and 9.1 ng g-1 in HS-SPME. The spiked recoveries and RSD were, respectively, 100.5% and 3.3% in HS-SDME and 98.1% and 3.6% in HS-SPME. HS-SDME is convenient to perform and produce results in a much cheaper way than HS-SPME and free from the inconveniences of memory effects. With GC-MS, this method has also been implemented as a rapid, reliable and green procedure (by GAPI and AGREE tools) for the sampling of VOCs in real samples of spices, flowers, and a beetle nut chewing sample illicitly containing tobacco.

Dispersive liquid-liquid microextraction and diffuse reflectance-Fourier transform infrared spectroscopy for iodate determination in food grade salt and food samples.

A novel method based on diffused reflectance Fourier-transform infrared spectroscopy (DRS-FTIR) was employed for iodate determination in food grade salt and food products. The method attained sensitivity that was comparable to or better than that in most of the contemporary spectrophotometric methods. This was realized through a combination of azo dye formation and dispersive liquid-liquid microextraction of dye when a 37-fold enrichment was obtained. FT-IR enabled integrating alternative target peak, and freedom in sample solvent composition relative to UV-visible spectrophotometry where the solvent polarity, pH, and presence of ions may affect the spectral properties of the measurable coloured species. Food samples containing iodide or covalently bonded iodine were oxidized with alkaline permanganate for mineralization and iodate formation. Optimization of both reaction conditions was carried out by means of response surface methodology. The method had a linear range 0.04-10 mg kg-1 iodate and limit of detection of 4.4 µg kg-1.

Combined liquid phase microextraction and fiber-optics-based cuvetteless micro-spectrophotometry for sensitive determination of ammonia in water and food samples by the indophenol reaction.

The Berthelot reaction for ammonia is revisited with the aim of miniaturization and addressing interferences as encountered with food and water samples. Headspace single drop microextraction of ammonia in phosphoric acid served to attain selectivity in complex matrices, and liquid-liquid microextraction of red or blue indophenol species into 1-octanol-isooctane (60:40, v/v) resulted into high sensitivity. Fiber-optics-based cuvetteless micro-spectrophotometry has been used for colorimetric determination on microliter volumes of extract. The linear dynamic range, limit of detection and enrichment factor have been found to be 0.2-3 mg kg-1, 0.14 mg kg-1 and 38, respectively, measuring red species for milk, cheese and beer (4.9-5.5% error; 4.8-6.3% RSD; n = 5); and 5-400 µg L-1, 0.4 µg L-1 and 137, respectively, measuring blue species for water samples (3.3-5.7% error; 3.6-6.8% RSD; n = 5). A plausible reaction scheme has been proposed for nitroprusside catalysis in indophenol reaction.

Perspective: Status and Future of Analytical Chemistry in India.

Relative to many other areas in chemistry, analytical chemistry appears singularly lagging behind in India despite the commendable growth it had shown in the past both in teaching and research. Certain presumptions in policy making and current educational practices are believed to be the crux of the problem.

Salting-out assisted liquid-liquid extraction for the determination of biogenic amines in fruit juices and alcoholic beverages after derivatization with 1-naphthylisothiocyanate and high performance liquid chromatography.

A new method for determining biogenic amines in fruit juices and alcoholic beverages is described involving reaction of biogenic amines with 1-naphthylisothiocyanate followed by extraction of 1-naphthylthiourea derivatives with water-miscible organic solvent acetonitrile when solvents phase separation occurred using ammonium sulphate, a process called salting-out assisted liquid-liquid extraction. The extract was analyzed by high-performance liquid chromatography with UV detection at 254nm. The new reagent avoided many of the inconveniences as observed with existing derivatizing agents, such as dansyl chloride and benzoyl chloride, in regard to their inselectivity, instability, adverse effect of excess reagent, and necessity to remove excess reagent. The procedure has been optimized with respect to reaction time and temperature, water-miscible extraction solvent, and salt for solvents phase separation. Use of reagent as dispersed phase in aqueous medium produced derivatives in high yield. A linear calibration was obtained between the amount of biogenic amines in range 1-1000µgL(-1) and peak areas of corresponding thioureas formed; the correlation coefficient was 0.9965, and the limit of detection and limit of quantification found were 1.1µgL(-1) and 3.2µgL(-1), respectively. The pre-concentration method gave an average enrichment factor of 94. The application of the method has been demonstrated in the determination of biogenic amines in commercial samples of fruit juices and alcoholic beverages. In spiking experiments to real samples, the average recovery found by the present method was 94.5% that agreed well with 95.8% obtained by established comparison methods.

Conversion to isothiocyanates via dithiocarbamates for the determination of aromatic primary amines by headspace-solid phase microextraction and gas chromatography.

A novel and highly selective method has been developed for the determination of aromatic primary amines by their conversion to dithiocarbamates by reaction with carbon disulphide, and then to isothiocyanates, which are volatile, by heating in the presence of a heavy metal ion. Zinc(II) was selected owing to its low toxicity and optimum yield of isothiocyanates. The latter were sampled by headspace-solid phase microextraction (HS-SPME) on divinylbenzene-carboxen-polydimethylsiloxane fibre, 50/30 µm. The HS-SPME procedure was optimized to provide adequate limits of detection in the analysis of aromatic amines in their real samples by gas chromatography with mass spectrometry (GC-MS) or flame ionization detection (GC-FID). The method gave rectilinear calibration graph, correlation coefficient and limit of detection, respectively, over the range 0.08-100 µg L(-1), 0.9950-0.9990 and 25-240 ng L(-1) in gas chromatography-mass spectrometry, and 0.01-10 mg L(-1), 0.9910-0.9991 and 0.8-3.0 µg L(-1) in gas chromatography-flame ionization detection. At two different levels, 10 and 40 µg L(-1), the range of intra-day RSD was 3.7-8.5% (GC-MS) and 3.3-9.2% (GC-FID), respectively. The proposed method is simple and rapid, and has been applied to determine aromatic primary amines in the environmental waters, food samples of ice cream powder and soft drinks concentrate, and food colours. The intra-day RSD in the analysis of real samples by GC-MS was in the range 3.6-6.2%. The food/colour samples were found to contain elevated levels of aniline and 2-toluidine.

Recent advances in applications of single-drop microextraction: a review.

During the past fifteen years since its introduction, single-drop microextraction has witnessed incessant growth in the range of applications of samples preparation for trace organic and inorganic analysis. This was mainly due to the array of modes that are available to accomplish extraction in harmony with the nature of analytes, and to use the extract directly for analysis by diverse instrumental methods. Whilst engineering of novel sorbent materials has expanded the sample capabilities of rival method of solid-phase microextraction, the single-drop microextraction - irrespective of the mode of extraction - uses common equipment found in analytical laboratories sans any modification, and in a much economic way. The recent innovations made in the field, as highlighted in this review article in the backdrop of historical developments, are due to the freedom in operational conditions and practicability to exploit chemical principals for optimum extraction and sensitive determination of analytes. Literature published till July 2011 has been covered.

Solid-phase extraction combined with headspace single-drop microextraction of chlorophenols as their methyl ethers and analysis by high-performance liquid chromatography-diode array detection.

Solid-phase extraction (SPE) of phenol and chlorophenols, their derivatization to methyl ethers, headspace single-drop microextraction (HS-SDME) of methyl ethers using 1-butanol as extraction solvent, and direct transfer of the drop into the injector for high performance liquid chromatography with diode array detection (HPLC-DAD) have been reported. A flanged-end polytetrafluoroethylene sleeve, 3 mm × 0.5mm, placed at the tip of the syringe needle, allowed the use of 10 µL solvent drop for extraction. The procedure has been optimized for variables involved in SPE and HS-SDME. A rectilinear relationship was obtained between the amount of chlorophenols and peak area ratio of their methyl ethers/internal standard (4-methoxyacetophenone) in the range 0.01-10 mg L(-1), correlation coefficient in the range 0.9956-0.9996, and limit of detection in the range 1.5-3.9 µg L(-1) when HS-SDME alone was used for sample preparation. When using coupled SPE and HS-SDME, the linear range obtained was 0.1-500 µg L(-1), correlation coefficient in the range 0.9974-0.9998, and the limit of detection in the range 0.04-0.08 µg L(-1). Spiked real samples have been analyzed with adequate accuracy, and application of the method has been demonstrated for the analysis of chlorophenols formed upon bamboo pulp bleaching.

Determination of amoxapine and nortriptyline in blood plasma and serum by salt-assisted liquid-liquid microextraction and high-performance liquid chromatography.

A new, selective and sensitive method has been developed for the determination of tricyclic antidepressant drugs, amoxapine and nortriptyline, in human blood plasma and serum, involving their reaction with allyl isothiocyanate and extraction of thiourea derivatives with water-miscible organic solvent acetonitrile. The phase separation was effected by addition of ammonium sulphate, a process called salt-assisted liquid-liquid microextraction. The extract was analyzed by HPLC with UV detection at 254 nm. The method has been optimized for derivatization reaction time and temperature, solvent for extraction, and salt for solvent phase separation. Under the optimal conditions, a linear calibration graph was obtained between the amount of drug and the peak area of thiourea derivatives in the range of 0.002-20 mg/L drugs. The correlation coefficient and limit of detection values for amoxapine and nortriptyline in serum/plasma samples were in the range of 0.9953-0.9999 and 0.46-0.58 µg/L, respectively. The recovery in spiking experiments ranged, respectively, 75-88% (RSD 3.4-7.2%) and 79-97% (RSD 3.7-7.9%) for the two drugs.

Headspace single-drop microextraction and cuvetteless microspectrophotometry for the selective determination of free and total cyanide involving reaction with ninhydrin.

Headspace single-drop microextraction has been used for the determination of cyanide with ninhydrin in combination with fibre-optic-based cuvetteless microspectrophotometry which accommodates sample volume of 1 microL placed between the two ends of optical fibres, and has been found to avoid salient drawbacks of batch methods. This method involved hydrocyanic acid formation in a closed vial, and simultaneous extraction and reaction with 2 microL drop of ninhydrin in carbonate medium suspended at the tip of a microsyringe needle held in the headspace of the acidified sample solution. The method was linear in range 0.025-0.5 mg L(-1) of cyanide. The headspace reaction was free from the interference of substances, e.g., thiocyanate, hydrazine sulphate, hydroxylammonium chloride and ascorbic acid. Sulphide was masked by cadmium sulphate, nitrite by sulphamic acid, sulphite by N-ethylmaleimide, and halogens by ascorbic acid. The limit of detection was found to be 4.3 microg L(-1) of cyanide which was comparable to existing most sensitive methods for cyanide. However, the present method is far more simple. The method was applied to acid-labile and metal cyanides complexes by treatment with sulphide when metal sulphides were precipitated setting cyanide ion free, and to iron(II) and (III) cyanide complexes by their decomposition with mercury(II), the mercury(II) cyanide formed was then determined. These pre-treatment methods avoided cumbersome pre-separation of cyanide by methods such as distillation or gas diffusion. The overall recovery of cyanide in diverse samples was 97% with RSD of 3.9%.

Headspace single-drop microextraction and fibre optics-based cuvetteless micro-spectrophotometry for the determination of chloride involving oxidation with permanganate.

Headspace single-drop microextraction has been investigated for the determination of chloride in conjunction with fibre optic-based cuvetteless micro-spectrophotometry which accommodates sample volume of 1 microL placed between the two ends of optical fibres. Method has been evolved for the determination of 0.025-4 mg L(-1) of chloride involving its oxidation with permanganate in sulphuric acid medium, and reaction of chlorine with 2 microL drop of starch-iodide reagent suspended at the tip of microsyringe needle in the headspace of the reaction mixture. The limit of detection was found to be 2.8 microg L(-1) of chloride which was better than obtained by existing methods. The method was highly selective and a number of ions which interfered severely in other methods did not affect the results. The method has been used to analyze water samples, inorganic compounds and cement when the overall recovery of chloride was 94.9% with a relative standard deviation of 3.9%.

Salt-assisted liquid-liquid microextraction with water-miscible organic solvents for the determination of carbonyl compounds by high-performance liquid chromatography.

A simple and rapid method has been reported for the determination of carbonyl compounds involving reaction with 2,4-dinitrophenylhydrazine and extraction of hydrazones with water-miscible organic solvent acetonitrile when the phase separation occurs by addition of ammonium sulphate, a process called salt-assisted liquid-liquid microextraction. The extract was analyzed by high-performance liquid chromatography with UV detection at 360 nm. The procedure has been optimized with respect to solvent suitable for extraction, salt for phase separation between water and organic solvent, reaction temperature and reaction time. The method has been validated when a linear dynamic range was obtained between the amount of analyte and peak area of hydrazones in the range 7 microg-15 mg L(-1), the correlation coefficient over 0.9964-0.9991, and the limit of detection in the range 0.58-3.2 microg L(-1). Spiked water samples have been analyzed with adequate accuracy, and application of the method has been demonstrated in the analysis of benzaldehyde formed as oxidation product in pharmaceutical preparation where benzyl alcohol is used as preservative, and for a keto drug dexketoprofen.

Liquid-phase microextraction and fibre-optics-based cuvetteless CCD-array micro-spectrophotometry for trace analysis.

Liquid-phase microextraction (LPME) has been investigated for trace analysis in the present work in conjunction with fibre-optic-based micro-spectrophotometry which accommodates sample volume of 1 microL placed between the two ends of optical fibres. Methods have been evolved for the determination of (i) 1-100 microM and 0.5-20 microM of thiols by single drop microextraction (SDME) and LPME in 25 microL of the organic solvent, respectively, involving their reaction with the Ellman reagent and ion pair microextraction of thiolate ion formed; (ii) 70 microg to 7 mg L(-1) of chlorine/chlorine dioxide by headspace in-drop reaction with alternative reagents, viz., mixed phenylhydrazine-4-sulphonic acid and N-(1-naphthyl)ethylenediamine dihydrochloride, o-dianisidine, o-tolidine, and N,N-diethyl-p-phenylenediamine; (iii) 0.2-4 mg L(-1) of ammonia by reaction with 2,4-dinitro-1-fluorobenzene to give 2,4-dinitroaniline which was diazotized and coupled with 1-naphthylamine, the resulting dye was subjected to preconcentration by solid-phase extraction and LPME; and (iv) 25-750 microg L(-1) of iodide/total iodine by oxidation of iodide by 2-iodosobenzoate, microextraction of iodine in organic solvent, and re-extraction into aqueous starch-iodide reagent drop held in the organic phase. LPME using 25-30 microL of organic solvent was found to produce more sensitive results than SDME. The cuvetteless spectrophotometry as used in combination with sample handling techniques produced limits of detection of analytes which were better than obtained by previously reported spectrophotometry.

Headspace in-drop derivatization of carbonyl compounds for their analysis by high-performance liquid chromatography-diode array detection.

A simple and rapid method has been reported for the determination of carbonyl compounds involving sample preparation by headspace single drop microextraction using 1-butanol as extraction solvent containing 2,4-dinitrophenylhydrazine for hydrazone formation, and direct transfer of the drop into the injector for high-performance liquid chromatography with diode array detection. An angle-cut polytetrafluoroethylene sleeve, 3mm x 0.5mm, was fixed at the tip of the syringe needle and this allowed the use of 7 microL drop of solvent drop for extraction and derivatization. The procedure has been optimized with respect to suitable solvent for headspace drop formation, drop volume, concentration of reagent, sample temperature, reaction time, and headspace-to-sample volume ratio. The method has been validated when rectilinear relationship was obtained between the amount of analyte and peak area ratio of hydrazones in the range 0.01-15 mg L(-1), the correlation coefficient over 0.996-0.999, and the limit of detection in the range 1.7-24.1 microg L(-1). Spiked real samples have been analyzed with adequate accuracy, and application has been demonstrated of the method for analysis of carbonyl compounds formed as oxidation products.

Coupled in-tube and on-fibre solid-phase microextractions for cleanup and preconcentration of organic micropollutants from aqueous samples and analysis by gas chromatography-mass spectrometry.

Matrix interference removal is an important step when large volumes of aqueous samples are required to be processed to detect trace levels of analytes. A combination of two sample extraction methods has been used in this work with the aim of cleanup and preconcentration of analytes. For first objective, mild but preferential sorption of a range of analytes has been performed with in-tube solid-phase microextraction (SPME) using polytetrafluoroethylene (PTFE) tubing, and for the second, the eluate from in-tube SPME was subjected to on-fibre SPME using DVB/Caboxen/PDMS (30/50 microm) fibre. Knitting of PTFE tubing created secondary flow pattern that enhanced radial diffusion and retention of organic analytes. Up to 2 mgL(-1) of a broad range of substances that are not extracted by PTFE include nitrogen containing aromatic heterocyclic compounds, anilines, phenols and certain organophosphorus pesticides, thus providing a clean extract using this method of sample preparation. The proposed combination of in-tube and on-fibre SPME produced a rectilinear calibration graph over 0.03-150 microgL(-1) of a range of analytes using 60 mL of aqueous sample. The overall recovery of analytes was in the range 27-78%. The detection limits were between 6.1 and 21.8 ngL(-1). The R.S.D. was in range 5.4-8.2% and 4.2-6.5% in the analysis of respectively 2 and 20 microgL(-1) of analytes.

Liquid-phase microextraction-gas chromatography-mass spectrometry for the determination of bromate, iodate, bromide and iodide in high-chloride matrix.

In the determination of bromate and iodate, any free bromide and iodide present was quantitatively removed by anion exchange with silver chloride exploiting the differences in silver salts solubility product, being AgCl, 1.8 x 10(-10), AgBr, 5.0 x 10(-13), AgI, 8.3 x 10(-17), AgBrO(3), 5.5 x 10(-5) and AgIO(3), 3.1 x 10(-8). The oxyhalides were reduced with ascorbic acid to halides and converted to 4-bromo-2,6-dimethylaniline and 4-iodo-2,6-dimethylaniline by their reaction with 2-iodosobenzoate in the presence of 2,6-dimethylaniline at pH 6.4 and 2-3, respectively. Single drop microextraction (SDME) of the haloanilines in 2 microl of toluene and injection of the whole extract into GC-MS, or liquid-phase microextraction (LPME) into 50 microl of toluene and injection of 2 microl of extract, resulted in a sensitive method for bromate and iodate. The latter method of extraction has been found more robust, sensitive and to give better extraction in shorter period than SDME. Total bromine/iodine was determined without any treatment with silver chloride. High concentration of chloride in the matrix did not interfere. A rectilinear calibration graph was obtained for 0.05 microg-25 mg l(-1) of bromate/bromide and iodate/iodide, the limit of detection were 20 ng l(-1) of bromate, 15 ng l(-1) of iodate, 20 ng l(-1) of bromide and 10 ng l(-1) of iodide (by LPME in 50 microl of toluene). The method has been applied to seawater and table salt. From the pooled data, the average recovery of spiked oxyhalide/halide to real samples was in range 96.7-105.7% with RSD in range 1.6-6.5%.

Optimization of experimental parameters in single-drop microextraction-gas chromatography-mass spectrometry for the determination of periodate by the Malaprade reaction, and its application to ethylene glycol.

The aim of present work was to optimize the experimental parameters in single drop microextraction under solution immersion (SDME) and headspace (HS-SDME) extraction modes for the determination of periodate using guaifenesine [3-(2'-methoxyphenoxy)-1,2-propane diol] and norephedrine (phenylpropanolamine) as new and alternative reagents for the Malaprade reaction. The reactions were complete within 5min resulting in the formation of 2-(2'-methoxyphenoxy)-acetaldehyde and benzaldehyde, respectively. SDME/HS-SDME of oxidation products with 2mul of anisole or 1mul of toluene, respectively, has permitted the determination of periodate at mugl(-1) concentration levels. The results indicated that HS-SDME (range 0.01-10mgl(-1), r(2)=0.9990; limit of detection 1.55mugl(-1)) was more sensitive than SDME (range 0.05-50mgl(-1), r(2)=0.9984; limit of detection 3.42mugl(-1)), and was inexpensive, rapid and convenient. Tolerance of excess of iodate has permitted the application of this method in the determination of ethylene glycol in motor oil; the average recovery on spiked sample was 98.6% with R.S.D. of 4.2%.

Liquid-phase microextraction and GC for the determination of primary, secondary and tertiary aromatic amines as their iodo-derivatives.

Presence of iodine in aromatic amines, introduced by their reaction with iodine, and other electron withdrawing substituents such as chlorine and nitro, has been found to afford excellent liquid-phase microextraction (LPME) in toluene and separation by gas chromatography in the determination of primary, secondary and tertiary aromatic amines. The effect is due to decreased basic nature of amines when electronegative substituents are present. Single drop microextraction (SDME) of the amines in 2mul of toluene and injection of the whole extract into GC, or LPME into 50mul of toluene and injection of 2mul of extract, were used. LPME has been found more robust and to give better extraction in shorter period than SDME. In SDME-GC-FID, the average correlation coefficient was 0.9939 and average limit of detection 25mugl(-1) (range 12-61mugl(-1)) whereas the corresponding values in LPME-GC-MS were, respectively, 0.9953 and 33ngl(-1) (range 18-60ngl(-1)). The method has been applied to determine aromatic amines in river water, dye factory effluents and food dye stuffs. The LPME was found as robust, rugged and simple extraction method.

Single drop microextraction or solid phase microextraction-gas chromatography-mass spectrometry for the determination of iodine in pharmaceuticals, iodized salt, milk powder and vegetables involving conversion into 4-iodo-N,N-dimethylaniline.

A rapid sequence of oxidation and iodination using 2-iodosobenzoate as an oxidizing agent and N,N-dimethylaniline as an iodine scavenger at pH 6.4, when 4-iodo-N,N-dimethylaniline is formed, has been used for the determination of iodide by GC-MS. Solid phase microextraction (SPME) and single drop microextraction (SDME) have been used for the extraction of the iodo-derivative and their relative efficiencies compared. Pharmaceutical samples were subjected to solid phase extraction (SPE) for cleanup and the eluate analyzed for iodide. Iodate in salt samples was reduced to iodide with ascorbic acid. Milk powder and dried vegetables were wet combusted with peroxydisulfate to liberate covalently bound iodine as iodate which was reduced before derivatization. A rectilinear calibration graph was obtained for 0.1 microg-10 mg l(-1) iodide by both extraction methods, the correlation coefficient and limit of detection (LOD) were 0.9995 and 25 ng l(-1) iodide by SPME method, and 0.9998 and 10 ng l(-1) iodide by SDME method, respectively. SDME appeared to be more efficient technique than SPME for the present system. From the pooled data, the average recovery of spiked iodide to real samples was 100.7% (range 96.5-107.0%) with an average R.S.D. of 3.1% (range 2.6-4.5%).

Determination of aromatic primary amines at microg l(-1) level in environmental waters by gas chromatography-mass spectrometry involving N-allyl-n'-arylthiourea formation and their on-line pyrolysis to aryl isothiocyanates.

Derivatization of aromatic primary amines to N-allyl-N'-arylthioureas by reaction with allyl isothiocyanate and GC-MS of the derivatives, when pyrolysis to aryl isothiocyanates occurs in the heated injector, has been used to determine aromatic amines in the range 0.5-50 microg l(-1) with a correlation coefficient, r, in the range 0.9902-0.9992. The limit of detection ranged 8 to 30 ng l(-1) when 60 ml of sample were preconcentrated, after derivatization, on a styrene-divinylbenzene copolymer sorbent. The pyrolytic cleavage of sym- and unsym-diaryl or alkyl-/arylthioureas has been rationalized. The chromatography of isothiocyanates is much superior to that of aryl amines and the specific mass fragmentation permits positive identification of amines. The method has been applied to spiked drinking water, groundwater and river water samples, when the recovery ranged from 84 to 109% with RSD of 5-9%, and to detect aromatic amines formed by reductive cleavage of azo dyes in effluents when the recovery of amine was in the range 81-95% with RSD 8-15%. The method is not applicable to nitroanilines.