The Influence of Roughness on Experimental Fault Mechanical Behavior and Associated Microseismicity.

Fault surfaces are rough at all scales, and this significantly affects fault-slip behavior. However, roughness is only occasionally considered experimentally and then often in experiments imposing a low-slip velocity, corresponding to the initiation stage of the earthquake cycle. Here, the effect of roughness on earthquake nucleation up to runaway slip is investigated through a series of dry load-stepping biaxial experiments performed on bare rock surfaces with a variety of roughnesses. These laboratory faults reached slip velocities of at least 100 mm/s. Acoustic emissions were located during deformation on bare rock surfaces in a biaxial apparatus during load-stepping experiments for the first time. Smooth surfaces showed more frequent slip instabilities accompanied by slip bursts and larger stress drops than rough faults. Smooth surfaces reached higher slip velocities and were less inclined to display velocity-strengthening behavior. The recorded and localized acoustic emissions were characterized by a greater proportion of large-magnitude events, and therefore likely a higher Gutenberg-Richter b GR-value, for smoother samples, while the cumulative seismic moment was similar for all roughnesses. These experiments shed light on how local microscopic heterogeneity associated with surface topography can influence the macroscopic stability of frictional interfaces and the associated microseismicity. They further provide a laboratory demonstration of roughness' ability to induce stress barriers, which can halt rupture, a phenomenon previously shown numerically.

The Permeability of Porous Volcanic Rock Through the Brittle-Ductile Transition.

The permeability of volcanic rock controls the distribution of pore fluids and pore fluid pressure within a volcanic edifice, and is therefore considered to influence eruptive style and volcano deformation. We measured the porosity and permeability of a porous volcanic rock during deformation in the brittle and ductile regimes. In the brittle regime, permeability decreases by a factor of 2-6 up to the peak stress due the closure of narrow pore throats but, following shear fracture formation, remains approximately constant as strain is accommodated by sliding on the fracture. In the ductile regime, permeability continually decreases, by up to an order of magnitude, as a function of strain. Although compaction in the ductile regime is localized, permeability is not reduced substantially due to the tortuous and diffuse nature of the compaction bands, the geometry of which was also influenced by a pore shape preferred orientation. Although the evolution of the permeability of the studied porous volcanic rock in the brittle and ductile regimes is qualitatively similar to that for porous sedimentary rocks, the porosity sensitivity exponent of permeability in the elastic regime is higher than found previously for porous sedimentary rocks. This exponent decreases during shear-enhanced compaction toward a value theoretically derived for granular media, suggesting that the material is effectively granulating. Indeed, cataclastic pore collapse evolves the microstructure to one that is more granular. Understanding how permeability can evolve in a volcanic edifice will improve the accuracy of models designed to assist volcano monitoring and volcanic hazard mitigation.

Physical characterization of fault rocks within the Opalinus Clay formation.

Near-surface disposal of radioactive waste in shales is a promising option to safeguard the population and environment. However, natural faults intersecting these geological formations can potentially affect the long-term isolation of the repositories. This paper characterizes the physical properties and mineralogy of the internal fault core structure intersecting the Opalinus Clay formation, a host rock under investigation for nuclear waste storage at the Mont Terri Laboratory (Switzerland). We have performed porosity, density, microstructural and mineralogical measurements in different sections of the fault, including intact clays, scaly clays and fault gouge. Mercury intrusion porosimetry analysis reveal a gouge that has a pore network dominated by nanopores of less than 10 nm, yet a high-porosity (21%) and low grain density (2.62 g/cm3) when compared to the intact rock (14.2%, and 2.69 g/cm3). Thus, a more permeable internal fault core structure with respect to the surrounding rock is deduced. Further, we describe the OPA fault gouge as a discrete fault structure having the potential to act as a preferential, yet narrow, and localized channel for fluid-flow if compared to the surrounding rock. Since the fault gouge is limited to a millimetres-thick structure, we expect the barrier property of the geological formation is almost not affected.

Earthquake Nucleation Along Faults With Heterogeneous Weakening Rate.

The transition from quasistatic slip growth to dynamic rupture propagation constitutes one possible scenario to describe earthquake nucleation. If this transition is rather well understood for homogeneous faults, how the friction properties of multiscale asperities may influence the overall stability of seismogenic faults remains largely unclear. Combining classical nucleation theory and concepts borrowed from condensed matter physics, we propose a comprehensive analytical framework that predicts the influence of heterogeneities of weakening rate on the nucleation length L c for linearly slip-dependent friction laws. Model predictions are compared to nucleation lengths measured from 2D dynamic simulations of earthquake nucleation along heterogeneous faults. Our results show that the interplay between frictional properties and the asperity size gives birth to three instability regimes (local, extremal, and homogenized), each related to different nucleation scenarios, and that the influence of heterogeneities at a scale far lower than the nucleation length can be averaged.

Initial effective stress controls the nature of earthquakes.

Modern geophysics highlights that the slip behaviour response of faults is variable in space and time and can result in slow or fast ruptures. However, the origin of this variation of the rupture velocity in nature as well as the physics behind it is still debated. Here, we first highlight how the different types of fault slip observed in nature appear to stem from the same physical mechanism. Second, we reproduce at the scale of the laboratory the complete spectrum of rupture velocities observed in nature. Our results show that the rupture velocity can range from a few millimetres to kilometres per second, depending on the available energy at the onset of slip, in agreement with theoretical predictions. This combined set of observations bring a new explanation of the dominance of slow rupture fronts in the shallow part of the crust or in areas suspected to present large fluid pressure.

Fast-moving dislocations trigger flash weakening in carbonate-bearing faults during earthquakes.

Rupture fronts can cause fault displacement, reaching speeds up to several ms(-1) within a few milliseconds, at any distance away from the earthquake nucleation area. In the case of silicate-bearing rocks the abrupt slip acceleration results in melting at asperity contacts causing a large reduction in fault frictional strength (i.e., flash weakening). Flash weakening is also observed in experiments performed in carbonate-bearing rocks but evidence for melting is lacking. To unravel the micro-physical mechanisms associated with flash weakening in carbonates, experiments were conducted on pre-cut Carrara marble cylinders using a rotary shear apparatus at conditions relevant to earthquakes propagation. In the first 5 mm of slip the shear stress was reduced up to 30% and CO2 was released. Focused ion beam, scanning and transmission electron microscopy investigations of the slipping zones reveal the presence of calcite nanograins and amorphous carbon. We interpret the CO2 release, the formation of nanograins and amorphous carbon to be the result of a shock-like stress release associated with the migration of fast-moving dislocations. Amorphous carbon, given its low friction coefficient, is responsible for flash weakening and promotes the propagation of the seismic rupture in carbonate-bearing fault patches.