Advances in Electrical Discharge Machining of Insulating Ceramics.

There are two main ways of carrying out the electrical discharge machining of the insulating ceramics: changing the electrical and chemical properties of ceramics due to additives in producing composites/nanocomposites and changing the electrical and chemical properties in the interelectrode gap. This review summarizes and analyzes the current data on the machinability in water suspension and hydrocarbons depending on the electrical properties of the ceramic composites and assisting means such as coating and powder. There are provided the existing approaches and original methods for solving the global problem of the electrical discharge machining of insulating ceramics, suggesting further development of the existing methods since, up to now, the experimental research is non-systemic. The dependencies of the machinability on the electrical properties of conductive ceramic composites, the specific electrical resistance of the assisting coating, and the assisting powder's band gap and concentration for machining insulating ceramics are revealed. The higher the electrical conductivity, the higher the machinability of ceramic composites, and the lower the band gap, the higher the machinability for insulating ceramics. Two technological gaps were revealed in the powder's concentration that can be a particular case of logarithmic decrement of attenuation. The proposed approach suggests using assisting powder with the lower band gap.

Investigation of Tribological Characteristics of PEO Coatings Formed on Ti6Al4V Titanium Alloy in Electrolytes with Graphene Oxide Additives.

Coatings with a thickness from ~40 to ~50 µm on Ti6Al4V titanium alloys were formed by plasma electrolytic oxidation (PEO) in a silicate-hypophosphite electrolyte with the addition of graphene oxide. The PEO treatment was carried out in the anode-cathode mode (50 Hz) at a ratio of anode and cathode currents of 1:1; their sum density was 20 A/dm2, and the treatment's duration was 30 min. The effect of the graphene oxide's concentration in the electrolyte on the thickness, roughness, hardness, surface morphology, structure, composition, and tribological characteristics of the PEO coatings was studied. Wear experiments, under dry conditions, were carried out in a ball-on-disk tribotester with an applied load of 5 N, a sliding speed of 0.1 m·s-1, and a sliding distance of 1000 m. According to the obtained results, the addition of graphene oxide (GO) into the base silicate-hypophosphite electrolyte leads to a slight decrease in the coefficient of friction (from 0.73 to 0.69) and a reduction in the wear rate by more than 1.5 times (from 8.04 to 5.2 mm3/N·m), with an increase in the GO's concentration from 0 to 0.5 kg/m3, respectively. This occurs due to the formation of a GO-containing lubricating tribolayer upon contact with the coating of the counter-body in the friction pair. Delamination of the coatings during wear occurs due to contact fatigue; with an increase in the concentration of GO in the electrolyte from 0 to 0.5 kg/m3, this process slows down by more than four times.

The Study of Radius End Mills with TiB2 Coating When Milling a Nickel Alloy.

Nickel alloy high-speed processing technology using ball-end mills is characterized by high contact temperature and leads to accelerated tool wear. One of the effective ways to increase its reliability and service life is to modify the surface by applying functional antifriction layers in addition to wear-resistant coatings. Diamond-like carbon is often used as the latter. However, at cutting speed, when a cutting-edge temperature exceeding 650 °C is reached, the material of this coating reacts actively with oxygen in the air, and the sharply increasing adhesive component of wear quickly incapacitates the milling tooth, limiting its performance. Applying a coating of titanium diboride as an antifriction layer on top of nanocrystalline composite nitride coatings with good resistance to abrasive wear can be a solution to this problem. Our experiments have shown that such technology makes it possible to obtain a twofold increase in durability compared to a tool with a diamond-like antifriction coating in conditions when the cutting edge of the tool is subjected to cyclic thermal shocks above 800 °C, and the durability period of the radius end mill is about 50 min.

Elemental and Thermochemical Analyses of Materials after Electrical Discharge Machining in Water: Focus on Ni and Zn.

The mechanism of the material destruction under discharge pulses and material removal mechanism based on the thermochemical nature of the electrical erosion during electrical discharge machining of conductive materials were researched. The experiments were conducted for two structural materials used in the aerospace industry, namely austenite anticorrosion X10CrNiTi18-10 (12kH18N10T) steel and 2024 (D16) duralumin, machined by a brass tool of 0.25 mm in diameter in a deionized water medium. The optimized wire electrical discharge machining factors, measured discharge gaps (recommended offset is 170-175 µm and 195-199 µm, respectively), X-ray photoelectron spectroscopy for both types of materials are reported. Elemental analysis showed the presence of metallic Zn, CuO, iron oxides, chromium oxides, and 58.07% carbides (precipitation and normal atmospheric contamination) for steel and the presence of metallic Zn, CuO, ZnO, aluminum oxide, and 40.37% carbides (contamination) for duralumin. For the first time, calculating the thermochemistry parameters for reactions of Zn(OH)2, ZnO, and NiO formation was produced. The ability of Ni of chrome-nickel steel to interact with Zn of brass electrode was thermochemically proved. The standard enthalpy of the Ni5Zn21 intermetallic compound formation (erosion dust) ΔH0298 is -225.96 kJ/mol; the entropy of the crystalline phase Scint is 424.64 J/(mol·K).

Electrical discharge machining of ceramic nanocomposites: sublimation phenomena and adaptive control.

The productivity of electrical discharge machining (EDM) is relatively low owing to the natural laws of electrical erosion. Precise EDM demands uninterrupted control of the discharge gap and adjustment of process parameters. It is particularly critical for processing large workpieces with complex linear surfaces and for materials with threshold conductivities such as the new advanced ceramic nanocomposites Al2O3+TiC and Al2O3+SiCw+TiC(30-40%). In these cases, adequate flushing of erosion products is hampered by the geometry of the working space or by the small value of the required discharge gap, which does not exceed 2.2-2.5 µm. The methods of adaptive control in modern computer numerical control systems of EDM equipment based on measuring the electrical parameters in the working zone have been shown to be ineffective in the cases described above. This study aims to investigate the natural phenomena of material sublimation under discharge pulses for conductive ceramics and nanocomposites. The measured conductivities of the samples are higher than the percolation threshold. However, the question of machinability remains open owing to detected processing interruptions and poor quality of machined surfaces. New knowledge on EDM of conductive ceramics and nanocomposites can improve the final quality of the machined surfaces and productivity of the method by the introduction of advanced monitoring and control methods based on acoustic emissions. The manuscript presents an up-to-date overview and current state of the research on the subject area. The obtained morphology of the samples and discussion of the findings complete the experimental part of the study. The scientific basis for a new type of adaptive control system is provided. This can improve the effectiveness of parameter control for machining conductive ceramics and nanocomposites and contribute to an increase in the EDM performance for the most critical cases.