Design of a compressed air modulator to be used in comprehensive multidimensional gas chromatography and its application in the determination of pesticide residues in grapes.

In this study, a new modulator that is simple, robust and presents low operation costs, was developed. This modulator uses compressed air to cool two small portions in the first centimeters of the second chromatographic column of a comprehensive multidimensional gas chromatography (GCxGC) system. The results show a variation in the peak area less than 3 and 5% to alkanes and pesticides, respectively. The standard deviations for the retention times in the first and second dimension are around 0.05 min and 0.05s for all the compounds. The system was optimized with n-alkanes. The GCxGC system proposed was applied in the determination of pyrethroid pesticides (bifenthrin, cypermethrin, deltamethrin, fenvalerate, esfenvalerate, cis- and trans-permethrin) in grape samples. Samples were extracted by the mini-Luke modified method and pesticides were quantified by comprehensive multidimensional gas chromatography with micro electron-capture detection (microECD). The values of method limit of quantification (LOQ) were 0.01-0.02 mg kg(-1) for all studied pyrethroid and the values of recovery were between 94.3 and 115.2%, with good precision (RSD<18.4%), demonstrating that the performance of the total method consisting of a modified Luke extraction method and determination by GCxGC-microECD are satisfactory. This study also showed that the system using a modulator with a double jet of compressed air has the potential for application in the analysis of a wider range of pesticide residues in other commodities since it provides low values of LOQ with acceptable accuracy and precision.

Improved fatty acid detection in micro-algae and aquatic meiofauna species using a direct thermal desorption interface combined with comprehensive gas chromatography-time-of-flight mass spectrometry.

Comprehensive two-dimensional gas chromatography (GC x GC) with time-of-flight mass spectrometry detection is used to profile the fatty acid composition of whole/intact aquatic microorganisms such as the common fresh water green algae Scenedesmus acutus and the filamentous cyanobacterium Limnothrix sp. strain MRI without any sample preparation steps. It is shown that the technique can be useful in the identification of lipid markers in food-web as well as environmental studies. For instance, new mono- and diunsaturated fatty acids were found in the C(16) and C(18) regions of the green algae S. acutus and the filamentous cyanobacterium Limnothrix sp. strain MRI samples. These fatty acids have not, to our knowledge, been detected in the conventional one-dimensional (1D) GC analysis of these species due to either co-elution and/or their presence in low amounts in the sample matrix. In GC x GC, all congeners of the fatty acids in these microorganisms could be detected and identified due to the increased analyte detectability and ordered structures in the two-dimensional separation space. The combination of direct thermal desorption (DTD)-GC x GC-time-of-flight mass spectrometry (ToF-MS) promises to be an excellent tool for a more accurate profiling of biological samples and can therefore be very useful in lipid biomarker research as well as food-web and ecological studies.

Determination of the carbon isotopic composition of whole/intact biological specimens using at-line direct thermal desorption to effect thermally assisted hydrolysis/methylation.

In this paper, we discuss the use of a direct thermal desorption (DTD) interface as an alternative to Curie-point flash pyrolysis system as an inlet technique in gas chromatography-combustion isotope-ratio mass spectrometry (GC/C-IRMS) analysis of whole/intact phytoplankton and zooplankton specimens. The DTD in combination with a combipal auto-injector is programmed to perform the injection, evaporation of solvents, transport of capped programmed-temperature vaporizer (PTV) liners to the PTV injector and chemical derivatisation (thermally assisted hydrolysis/methylation; THM) such that a profile of a cellular fatty acids is obtained. Flow-cytometric sorted microalgae and handpicked zooplankton are used as samples with trimethylsulfonium hydroxide (TMSH) as methylating reagent. A major advantage of this novel approach over the Curie-point technique is the automation of the total procedure, which allows unattended analysis of large sample series. The profiles and delta(13)C carbon isotopic signatures of the fatty acid methyl esters (FAMEs) produced are very similar to those obtained using the Curie-point flash pyrolysis method. It is shown that algal samples must be kept no longer than 48 h in the DTD sample tray prior to the THM-analysis in order to maintain the integrity of their FAME profile.

Fatty acid profiling of raw human plasma and whole blood using direct thermal desorption combined with gas chromatography-mass spectrometry.

Gas chromatography (GC) has in recent times become an important tool for the fatty acid profiling of human blood and plasma. An at-line procedure used in the fatty acid profiling of whole/intact aquatic micro-organisms without any sample preparation was adapted for this work. A direct thermal desorption (DTD) interface was used to profile the fatty acid composition of human plasma and whole human blood of eight volunteers in a procedure omitting the usual lipid extraction steps that precede sample methylation in the traditional (off-line) protocols. Trimethylsulfonium hydroxide (TMSH) was used as reagent for thermally assisted methylation. In a fully automated manner, the liner of the GC injector is used as a sample-and-reaction container with the aid of the DTD interface. The fatty acid methyl ester (FAME) profiles obtained using this novel approach, were very identical to those obtained when the traditional off-line protocol was applied. FAME yields obtained in the at-line DTD method were found to be very similar for saturated fatty acids, but significantly higher for polyunsaturated fatty acids compared to off-line yields. As a result of the contribution of circulating cell membranes in blood, substantial differences were observed when the amount of FAMEs obtained in whole human blood and human plasma samples were compared after their analysis. Thanks to the fully automated operation of this novel procedure, large series of analyses can easily be performed.

Characterization of lipids in complex samples using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry.

Most lipids are a complex mixture of classes of compounds such as fatty acids, fatty alcohols, diols, sterols and hydroxy acids. In this study, the suitability of comprehensive two-dimensional gas chromatography coupled to a time-of-light mass spectrometer is studied for lipid characterization in complex samples. With lanolin, a refined wool wax, as test sample, it is demonstrated that combined methylation plus silylation is the preferred derivatization procedure to achieve (i) high-quality GC x GC separation and (ii) easily recognizable ordered structures in lipid analysis. Optimization of the GC x GC column combination, the influence of the temperature programme on the quality of the separation, and the potential and limitations of automated TOF-MS-based identification are discussed. The combined power of a 2D separation, ordered structures and MS detection is illustrated by the identification of several minor sample constituents.

Improved determination of flavour compounds in butter by solid-phase (micro)extraction and comprehensive two-dimensional gas chromatography.

The practicability and potential of comprehensive two-dimensional gas chromatography (GC x GC) coupled to both conventional flame ionisation (FID) and time-of-flight mass spectrometric (TOF-MS) detection, were compared with those of conventional one-dimensional (1D) GC, with the determination of flavour compounds in butter as an application. For polar flavour compounds, which were collected from the aqueous fraction of butter by means of solid-phase extraction (SPE), it was found that GC x GC dramatically improves the overall separation. Consequently, quantification and preliminary identification based on the use of ordered structures, can be performed more reliably. The improvement effected by replacing 1D-GC by GC x GC is considerable also in the case of TOF-MS detection, as illustrated by the high match factors generally obtained during identification. GC x GC was also used successfully for the characterisation of volatile flavour compounds in the headspace of butter collected by solid-phase microextraction (SPME) and to study the effect of heat treatment on the composition of butter samples in more detail.

Twin comprehensive two-dimensional gas chromatographic system: concept and applications.

A twin GC x GC system has been designed which enables the analysis of a sample by means of two different and independent column combinations simultaneously. Both combinations are incorporated in the same oven, using the same temperature programme, and are fed using a 50:50 column-entrance-split. It is demonstrated that, employing combinations of a conventional non-polar x polar and a reversed-type polar x non-polar column set, the information content is as high, and the analytical performance is as good as when using two separate GC x GC systems. That is, there is an appreciable gain of time and a reduction of costs without any loss of quality. The general usefulness of performing, and comparing two mutually different GC x GC runs is further illustrated with FAMEs in olive oil, and pollutants in a sediment sample.

Fast miniaturised sample preparation for the screening and comprehensive two-dimensional gas chromatographic determination of polychlorinated biphenyls in sludge.

Polychlorinated biphenyls (PCBs) in sludge are usually extracted by a technique such as Soxhlet with subsequent fractionation prior to long GC runs using GC-ECD or GC-HRMS. In this study, the extraction of selected chlorinated biphenyls (CBs) from a spiked sludge sample by three rapid techniques, i.e. ultrasonic (USE), pressurised-liquid (PLE), and microwave-assisted (MAE) extraction using a domestic microwave, was studied, with subsequent direct GC-ECD, GC-MS, or GC x GC-microECD analysis of the extracts. The main goal was to select an appropriate, and miniaturised, extraction method after only a brief optimisation and demonstrate the power of GC x GC analysis of dirty extracts. For PLE similar CB recoveries were found when extracting with either n-hexane or n-hexane/acetone (1/1). For USE and MAE, n-hexane/acetone (1/1) was the preferred extraction solvent. USE gave the best recoveries (80-95%; except 130% for CB 105). The only clean-up needed prior to GC-MS or GC x GC-gECD analysis was the removal of sulphur-containing compounds. GC-ECD was not suitable for these dirty extracts. The lowest LODs for the CBs (20 fg or 0.1 ng/g sludge) were found when combining USE and GC x GC-microECD, because of the powerful extraction, high separation power and excellent detectability provided by this technique.

Comprehensive two-dimensional gas chromatography coupled to a rapid-scanning quadrupole mass spectrometer: principles and applications.

The principles, practicability and potential of comprehensive two-dimensional (2D) gas chromatography coupled to a rapid-scanning quadrupole mass spectrometer (GC x GC-qMS) for the analysis of complex flavour mixtures in food, allergens in fragrances and polychlorinated biphenyls (PCBs) were studied. With a scan speed of 10,000 amu/s, monitoring over a mass range of up to 200 atomic mass unit (amu) can be achieved at an acquisition frequency of 33 Hz. Extending this mass range and/or increasing the data acquisition frequency results in a loss of spectral quality. Optimal parameter settings allow, next to unambiguous identification/confirmation of target compounds on the basis of high-quality mass spectra, fully satisfactory quantification (three to four modulations per peak) with linear calibration plots and detection limits in the low-pg level. The potential of time-scheduled data acquisition to increase the effective mass range within one GC x GC run was also explored. The analyses, with baseline separation of the flavours, allergens and PCB target compounds, took less than 30 min.

Miniaturised pressurised liquid extraction of chloroanilines from soil with subsequent analysis by large-volume injection-gas chromatography-mass spectrometry.

A number of chloroanilines were extracted from soil by means of miniaturised pressurised liquid extraction (PLE). The extraction procedure was optimised for both large-volume on-column (LV-OC) and programmed-temperature vaporisation (PTV) injections combined with GC-MS. Hexane was the only extraction solvent suited for LV-OC and hexane/acetone gave the best results when using a PTV. Overall, the hexane/acetone-plus-PTV procedure shows better results than the hexane-plus-LV-OC method in terms of analyte recovery (36-109% versus 5-87%), repeatability (8-13% versus 4-31%) and detection limits. Both approaches allow detection of the chloroanilines in complex soil samples down to the 5-50 ng/g range. However, the PTV-based procedure is superior as regards robustness: over one hundred samples can be analysed without any maintenance being required.

Comprehensive two-dimensional gas chromatography of complex samples by using a 'reversed-type' column combination: application to food analysis.

The practicability and potential of a non-orthogonal approach in comprehensive two-dimensional gas chromatography (GC x GC) were studied and compared to those of the orthogonal approach for two different complex matrices, and using conventional flame ionisation (FID) and time-of-flight mass spectrometry (ToF MS) detection. The separation of a diesel oil showed that the non-orthogonal approach also provides interesting, but completely reversed, ordered structures. For the more extensively studied flavour analysis in food samples, improved peak shapes and, also, different types of ordered structures and retention behaviour, and improved detectability for polar compounds make the two approaches complementary to each other. As a consequence, identification and/or determination of targets and/or unknowns can be performed more reliably. Analytical performance (close to three-order linearity; LODs, 2-30 pg injected in most cases; R.S.D.s, 1-6% (n = 6)) was fully satisfactory.

Evaluation of modulators and electron-capture detectors for comprehensive two-dimensional GC of halogenated organic compounds.

Different cryogenic and a heated GC x GC modulator(s) were evaluated and compared for the analysis of high-boiling halogenated compounds. The cryogenic modulators investigated were: (i) the longitudinally modulated cryogenic system; (ii) the liquid-nitrogen-cooled jet modulator (KT2001); (iii) a dual-jet CO2 modulator (made in-house); (iv) a semi-rotating cryogenic modulator (made in-house) and (v) a CO2 loop modulator (KT2003); the heated modulator was the slotted heater system (sweeper). Each modulator was optimised with respect to analyte peak widths at half height in the second-dimension. n-Alkanes, chlorinated alkanes, polychlorinated biphenyls (PCBs) and fluorinated polycyclic aromatic hydrocarbons (F-PAHs) were used as test analytes. The flow rate of the coolant was found to be an important parameter, i.e. the flow rate of the gaseous nitrogen in the KT2001, and of the liquid CO2 in the other cryogenic modulators. For the slotted heater the stroke velocity and pause time were important parameters. This modulator had a limited application range in terms of temperature due to a necessary 100 degrees C difference between sweeper and oven temperature. All cryogenic modulators were found to be suitable for the GC x GC analysis of high-boiling compounds, but the CO2 modulators are to be preferred to the KT2001 due to a wider application range and slightly narrower peaks. As regards the performance of three commercially available electron-capture detectors (ECDs), the aim was to obtain narrow peak widths in GC x GC, i.e. to avoid band broadening caused by the cell volume. The most important parameters were the flow rate of the make-up gas and the detector temperature which both should be as high as possible. Comparison of analyte peak widths obtained with ECD mode and flame ionisation detection (FID) showed that all ECDs exhibited band broadening compared to the FID. The narrowest peaks were obtained with the Agilent micro-ECD, which has a cell volume of only 150 microl.

Comprehensive two-dimensional gas chromatography with atomic emission detection and correlation with mass spectrometric detection: principles and application in petrochemical analysis.

Comprehensive gas chromatography (GC x GC) has been combined with atomic emission detection (AED) to enable element-selective detection. Under optimised experimental conditions, the requirement of minimum five data points across a peak can be obtained even for analytes eluting early from the second-dimension column. Simple manipulation of the results allows the combined presentation of up to four sets of elemental data in one two-dimensional plot. GC x GC with AED and mass spectrometric (MS) detection in petrochemical analysis for fingerprinting as well as the identification of N- and S-containing unknowns is presented as an application.

Comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometric detection for the trace analysis of flavour compounds in food.

The practicability and potential of comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry (GC x GC-TOF-MS) for the analysis of complex flavour mixtures in food were studied. With the determination of key flavour targets in dairy samples as an example, it was demonstrated that GC x GC dramatically improves the separation. As a consequence, identification and, more importantly, quantification down to the ng/g level can be performed more reliably: background interferences largely disappear. Next to the peak table generated from the GC-TOF-MS software after data processing, the additional use of well-ordered patterns in the 2D-plane and information from second-dimension retention times can substantially help the identification of unknowns. The technique was successfully used for an evaluation of extraction techniques and the characterisation of different types of samples.

Role of the retaining precolumn in large-volume on-column injections of volatiles to gas chromatography.

In the present study the retaining precolumn, which is commonly used in a set-up for large-volume on-column injections, or when solid-phase extraction (SPE) or liquid chromatography is coupled to gas chromatography (CC), was removed after varying its length from the standard length of 3 m down to zero. A dramatic increase of the evaporation rate of the injected organic solvent was obtained from a typical value of 100 microl/min up to 300 microl/min. The increased evaporation rate allowed (i) injection of a larger volume in the same retention gap, (ii) faster injection/transfer of the organic solvent and (iii) reduction of the transfer temperature. As volatile compounds under partially concurrent solvent evaporation conditions are easily lost once the organic solvent has been removed via a solvent-vapour exit (SVE), the parameters for large-volume injection, i.e. the evaporation rate and injection speed, were optimised using accurate measurements of the real flow-rate of the carrier gas into the GC system. All these options have been evaluated over the last 4 years. In order to demonstrate that omitting the retaining precolumn had no effect on the application range of the on-column interface, analytes as volatile as benzene were injected into GC-MS using 50-200 microl of n-pentane solutions. Contaminants were extracted from river water and wastewater into n-pentane using in-vial liquid-liquid extraction. The detection limits for benzene, toluene, ethylbenzene and m-xylene were approximately 10 ng/l. To obtain optimum results the SVE had to be closed 1 s before the end of evaporation. Several brands of n-pentane were analysed to check for the presence of benzene. Most of them contained interfering compounds and benzene at the low microg/l level and therefore had to be cleaned by means of column chromatography. As another example C8-C17 alkylphenones were extracted from wastewater with n-hexane. Detection limits were 10-40 ng/l.

Unravelling the composition of very complex samples by comprehensive gas chromatography coupled to time-of-flight mass spectrometry. Cigarette smoke.

The potential and current limitations of comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry (GC x GC-TOF-MS) for the analysis of very complex samples were studied with the separation of cigarette smoke as an example. Because of the large number of peaks in such a GC x GC chromatogram it was not possible to perform manual data processing. Instead, the GC-TOF-MS software was used to perform peak finding, deconvolution and library search in an automated fashion; this resulted in a peak table containing some 30000 peaks. Mass spectral match factors were used to evaluate the library search results. The additional use of retention indices and information from second-dimension retention times can substantially improve the identification. The combined separation power of the GC x GC-TOF-MS system and the deconvolution algorithm provide a system with a most impressive separation power.

Comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometric detection applied to the determination of pesticides in food extracts.

The separation provided by conventional gas chromatography (1D-GC) can be significantly enhanced by using comprehensive two-dimensional GC (GC X GC) instead. Combination with mass spectrometric detection is desirable for unambiguous confirmation of target compounds and the provisional identification of unknowns. A GC X GC system using a cryogenic modulator was coupled to a time-of-flight mass spectrometric (TOF MS) detector. With the determination of pesticides in vegetable extracts as an example, it was demonstrated that GC X GC improves the separation dramatically. All 58 pesticides of interest could be identified using their full-scan mass spectra, which was not possible when using ID-GC-TOF MS. In addition, the high scan speed of the TOF MS allowed the deconvolution of compounds partly co-eluting in GC X GC.

At-line gas chromatographic-mass spectrometric analysis of fatty acid profiles of green microalgae using a direct thermal desorption interface.

Thermally assisted hydrolysis and methylation-gas chromatography (THM-GC) is an important tool to analyse fatty acid in complex matrices. Since THM-GC has major drawbacks such as isomerisation when applied to fatty acids in natural matrices, a direct thermal desorption (DTD) interface and an incubation time of 30 min were used to circumvent these problems. Using vegetable oils such as sunflower oil and triarachidonin, the conversion of triglycerides into their fatty acid methyl esters (FAMEs) was investigated. The yields using a DTD (and trimethylsulfonium hydroxide as a reagent) were found to be similar or even higher than when applying a conventional off-line method, while the FAME profiles were identical. When the procedure was applied to analyse the FAME profiles of microbial cells in a methanolic or aqueous suspension, it was found that accurate profiles are obtained for such samples. Thus, the present approach opens the route to analyse fatty acids in microbial cells in a fully automated fashion, which will allow high sample throughput.