Measurement of tooth displacement.

The periodontium is a biological structure that supports the tooth in the jaw and behave as a developmental, biological, and functional unit. Teeth may be considered to be 'suspended' in their tooth sockets which provides teeth the ability to move in response to an applied load. In terms of the protection the suspension effect of the periodontal ligament may offer dental restorations, movement in an axial direction is of interest. No device or system to measure this movement is readily available, thus a novel approach had to be developed to address the questions of this research. The device developed allowed images to be taken of the participants teeth before, during and after a participant bit down on the tooth and used to measure the displacement of the tooth in image processing software. Average maximum tooth displacement from all participants of 73.8 µm (sd = 22.5 µm) were recorded. Longer application time of bite force was associated with greater cumulative tooth displacement, for a given level of force, and female participants experienced approximately 2 µm more displacement per Newton than males. The device and methods utilised in this study has shown good potential as a measurement protocol for measurement of vertical tooth movements in vivo. The response to load the teeth in this study has shown, highlighted the visco-elastic properties of the periodontal ligament and the amount of movement recorded supports the protection that controlled tooth movement offers teeth.

Anti-biofilm activity of silver nanoparticle-containing glass ionomer cements.

OBJECTIVE: To develop a silver nanoparticle (AgNP) formulation for incorporation into glass ionomer cements (GICs) which minimises biofilm growth on restoration surfaces. METHODS: GICs, Fuji IX, Ketac Molar, and Riva Selfcure were modified with 6, 10 and 24 µg per GIC capsule of α-lipoic acid-capped AgNPs. Monoculture biofilms of Streptococcus mutans were cultured (72 h) on GIC specimens (n = 3) and biofilm accumulation was quantified using a viability stain with confocal laser scanning microscopy. Compression strength and flexural strength (CS & FS) were measured according to ISO 9917-1:2007 (n = 8, n = 25). GIC colour was measured at 0, 1, and 14 days following AgNP incorporation using a digital spectrophotometer. Silver release from AgNP-modified GIC specimens was monitored at 1, 3, 7 and 14 days using inductively coupled plasma-mass spectrometry. RESULTS: AgNP-modified Fuji IX demonstrated the greatest reduction in biofilm accumulation, with 10 µg Ag/capsule inhibiting biofilm formation by 99%. Ketac Molar and Riva Selfcure required 24 µg Ag/capsule to achieve 78% biofilm reduction. AgNP-modified GICs demonstrated significantly higher CS and FS than sintered silver-containing GICs, and possessed equivalent or higher strength values when compared to unmodified GICs. The colour shades of AgNP-modified GICs were more comparable to VITA shades of non-modified GICs than were sintered silver-containing GICs. The silver (≥99.6%) remained within the GIC for at least two weeks following incorporation. SIGNIFICANCE: AgNP-modified GICs exhibited significant antibiofilm activity and retained mechanical properties equivalent or superior to non-modified GICs. AgNP-modified GICs could reduce bacterial colonisation on and around restorations thereby reducing restoration failure caused by secondary caries.

Development of a bite force transducer for measuring maximum voluntary bite forces between individual opposing tooth surfaces.

Bite forces are studied in order to understand a wide range of factors pertaining to the mastication system. Various strain gauge transducers have been employed to measure bite forces, with several descriptions of these available in the literature; unfortunately, many reports provide insufficient detail to enable accurate reproduction. The aim of this project was to develop a bite force transducer with the capability of measuring maximum voluntary bite forces between individual opposing tooth surfaces. Furthermore, in an attempt to address the issue of vague device descriptions in the available literature, a detailed account of the transducer development has been included. A novel strain gauge transducer was designed and built. Bite forces of forty individuals were measured to verify the capabilities and clinical application of the device.

Scalp simulation - A novel approach to site-specific biomechanical modeling of the skin.

OBJECTIVES: This study aimed to determine the hardness of the human scalp in vivo in order to identify an appropriate scalp simulant, from a range of commercially available silicone materials, for force impact assessment. Site-dependent variation in scalp hardness, and the applicability of contemporary skin simulants to the scalp were also considered. MATERIALS AND METHODS: A Shore A-type durometer was used to collected hardness data from the scalps of 30 human participants (five males and five females in each of the three age categories: 18-30, 31-40, 41-50) and four commercially available silicones (light, medium, and heavy-bodied PVS, and duplication silicone). One-sample t-tests were used to compare the mean hardness of simulants to that of the scalp. Site-dependent variation in the hardness of the scalp was assessed using a mixed-model repeated measures ANOVA. RESULTS: Mean human scalp hardness derived from participants was 20.6 Durometer Units (DU; SD = 3.4). Analysis revealed only the medium-bodied PVS to be an acceptable scalp simulant when compared to the mean hardness of the human scalp (p = 0.869). Scalp hardness varied significantly anteroposteriorly (with an observable linear trend, p < 0.001), but not mediolaterally (p = 0.271). Comparisons of simulants to site-specific variation in scalp hardness anteroposteriorly found the medium-bodied PVS to be only suitable in the central region of the scalp (p = 0.391). In contrast, the duplication silicone (p = 0.074) and light-bodied PVS (p = 0.147) were only comparable to the posterior region. CONCLUSIONS: Contemporary skin simulants fail to accurately represent the scalp in terms of hardness. There is strong support for the use of medium-bodied PVS as a scalp simulant. Human scalp hardness varies significantly anteroposteriorly, but not mediolaterally, corresponding to regional anatomical variation within the scalp. A number of materials were identified as potential simulants for different regions of the scalp when more site-specific simulant research is required.

Estimation of jaw-opening forces in adults.

OBJECTIVES: To estimate maximum jaw-opening forces in healthy participants of diverse ancestry and to estimate whether opening forces are associated with sex, age and anthropometric parameters such as height, weight and BMI. SETTING AND SAMPLE POPULATION: One hundred and forty-nine participants aged 20-60 years with overall good oral and general health. Exclusion criteria included myofascial or neck pain, symptomatic temporomandibular joint disorders (TMD), current orthodontic treatment or the absence of a natural dentition. MATERIAL AND METHODS: Jaw-opening forces were measured with an adjustable rigid extra-oral device connected to a 1000 N load cell. Seven attempts were recorded, with 10 seconds interval. Median force values were obtained after discarding the first and last attempt. The height and weight of each participant were measured and recorded, alongside age, sex and ethnicity. RESULTS: Men had greater maximum opening force median values than women (P < .001). Median (IQR) values for women were 41.16 N (30.44) and 79.00 N for men (63.86). Jaw-opening force values were poorly associated with biological and anthropometric parameters. CONCLUSION: In this study, which included a large sample of participants of broad age range and from a demographically diverse background, jaw-opening force values were greater in males than in females; however, force values were poorly associated with biological and anthropometric parameters. Future studies should explore the potential of this method as a screening tool for TMJ disorders and other conditions.

Intraoral pH and temperature during sleep with and without mouth breathing.

To measure and compare the intraoral pH and temperature of individuals during sleep with and without mouth breathing. Ten healthy participants [mean age = 25·8 (± 4·3)] wore a custom-made appliance fitted with a pH probe and thermocouple for two sets of 48 h. Continuous pH and temperature measurements were taken from the palatal aspect of the upper central incisors. To simulate mouth breathing during sleep, participants wore a nose clip for two nights of the four, with the first group (n = 5) wearing the nose clip during the first night and the rest (n = 5) wearing the nose clip during the second night of sleep to balance any potential bias from the wearing sequence. Both qualitative and quantitative analyses were conducted. The mean intraoral pH during daytime was 7·3 (± 0·4) and during sleep was 7·0 (± 0·5). The mean intraoral pH during sleep with mouth breathing was 6·6 (± 0·5), which was statistically significant compared with the normal sleep condition (P < 0·01). The intraoral pH decreased slowly over the hours of sleep in all participants. When sleeping with forced mouth breathing, intraoral pH showed a greater fall over a longer period of time. The mean intraoral temperature was 33·1 °C (± 5·2) during daytime and 33·3 °C (± 6·1) during sleep, with no statistical significance between sleep with and without mouth breathing (P > 0·05). The results suggest that mouth breathing during sleep is related to a decrease in intraoral pH compared with normal breathing during sleep, and this has been proposed as a causal factor for dental erosion and caries.

Simulating backspatter of blood from cranial gunshot wounds using pig models.

Few studies have examined the biomechanical basis for backspatter from cranial gunshot wounds. Backspatter is material which travels against the direction of fire following ejection from a gunshot entrance wound. Our paper focuses on the use of animals for reconstructing this phenomenon. Five live pigs and several slaughtered pigs were shot using either 9 × 19 mm, 115 grain, full metal jacketed ammunition or .22 long rifle, 40 grain, lead, round-nose ammunition. A high-speed camera was used to record the entrance wound formation and backspatter. A small amount of backspattered material was produced with all targets, and blood backspatter was seen in a few cases. However, we conclude that our model provides an understanding of the phenomenon of backspatter and the physical mechanisms associated with it. The various components of the mechanism of backspatter formation are complex and overlap. The principle mechanism observed in pig cranial gunshots was the high-speed impact response of the skin overlying the skull bone. This study has also produced evidence supporting the view that backspatter can result from the splashing of superficial blood if it is already present on the skin. Subcutaneous gas effects have been demonstrated for backspatter from contact shots. There has been no clear evidence of the role of the collapse of a temporary cavity within the brain.

Continuous measurement of intra-oral pH and temperature: development, validation of an appliance and a pilot study.

To describe a novel approach for continuous measurement of intra-oral pH and temperature in individuals carrying out normal daily activities over 24 h. We designed, validated and constructed a custom-made appliance fitted with a pH probe and a thermocouple. Six subjects wore the appliance over a 24-h period for two non-consecutive days, while the intra-oral pH and temperature were measured continuously and recorded. Intra-oral pH and temperature were very similar across different recording days, the difference being not statistically significant (P ≥ 0.14). There was a noticeable difference in the pattern of variation of pH between day and night. During the day, the mean pH was 7.3 (±0.4) and dropped markedly only after consumption of acidic food and drinks. The intra-oral pH decreased slowly during sleep with an average pH of 6.6 (±0.4) being recorded. The difference between day and night was statistically significant (P = 0.002). The mean intra-oral temperature was 33.9 °C (±0.9) during daytime and 35·9 °C (±0·5) during sleep (P = 0.013) with minor fluctuations occurring over 24 h. The continuous and simultaneous intra-oral pH and temperature measurement system described in this report is reliable, easy to construct, able to measure variables over a sustained period and may serve as a future diagnostic tool in a number of applications.

Quantification of subconcussive impact forces to the head using a forensic model.

Concussive and subconcussive head injury is a global phenomenon that affects millions of people each year. Concussive injury has been extensively studied in sport, which has led to a greater understanding of the biomechanical forces involved and guidelines aimed at preventing athletes from playing while concussed. Subconcussive forces by definition do not meet the threshold for concussion but nonetheless may have significant long term consequences due to the repetitive pattern of injury to the head. Quantifying these impact forces using a forensic head model provides the groundwork for future studies by establishing a range or threshold of subconcussive impact forces that could be correlated with clinical assessments. The use of a forensic head model has distinct advantages in terms of ethics and safety.

New insights into polar overdominance in callipyge sheep.

The callipyge phenotype in sheep involves substantial postnatal muscle hypertrophy and other changes to carcass composition. A single nucleotide polymorphism in the DLK1-DIO3 imprinted gene cluster alters gene expression of the paternal allele-specific protein-coding genes and several maternal allele-specific long noncoding RNA and microRNA when the mutation is inherited in cis. The inheritance pattern of the callipyge phenotype is polar overdominant because muscle hypertrophy only occurs in heterozygous animals that inherit a normal maternal allele and the callipyge SNP on the paternal allele (+/C). We examined the changes of gene expression of four major transcripts from the DLK1-DIO3 cluster and four myosin isoforms during the development of muscle hypertrophy in the semimembranosus as well as in the supraspinatus that does not undergo hypertrophy. The homozygous (C/C) animals had an intermediate gene expression pattern for the paternal allele-specific genes and two myosin isoforms, indicating a biological activity that was insufficient to change muscle mass. Transcriptome analysis was conducted by RNA sequencing in the four callipyge genotypes. The data show that homozygous animals (C/C) have lower levels of gene expression at many loci relative to the other three genotypes. A number of the downregulated genes are putative targets of the maternal allele-specific microRNA with gene ontology, indicating regulatory and cell signaling functions. These results suggest that the trans-effect of the maternal noncoding RNA and associated miRNA is to stabilize the expression of a number of regulatory genes at a functional, but low level to make the myofibers of homozygous (C/C) lambs less responsive to hypertrophic stimuli of the paternal allele-specific genes.

Dental technology services and industry trends in New Zealand from 2010 to 2012.

OBJECTIVE: To provide a snapshot of the New Zealand dental technology industry and influencing factors. BACKGROUND: Developing an understanding of the commercial dental laboratory environment in New Zealand can provide insight into the entire dental industry. METHODS: A web-based survey was the primary method for data collection, with separate questionnaires used for dental laboratory owners and dental technician employees. RESULTS: The mean net income for dental laboratory owners in New Zealand was similar to that of the United Kingdom, at $40.50 per hour. Clinical dental technicians are the highest paid employees, with a mean of $33.49 per hour. The mean technical charge for complete dentures was $632.59; including clinical services, it was $1907.00. The mean charge for a porcelain-fused-to-metal (PFM) crown was $290.27. Dental laboratory owners expressed fear about the possibility of losing dental clients to overseas laboratories due to the availability and cheap charge of offshore work. Only 25.4% of dental laboratories surveyed had computer-aided design (CAD) facilities, and even fewer (7.9%) had computer-aided manufacturing (CAM) systems. CONCLUSION: Clinical dental technology appears to be prospering. The dental technology industry appears to be adapting and remains viable, despite facing many challenges.

Microstructural analysis of Co-Cr dental alloy at the metal-porcelain interface: a pilot study.

OBJECTIVE: The purpose of the study was to observe whether conventional porcelain firings had an effect on the underlying microstructure of cobalt-chromium alloys used in porcelain-fused-to-metal systems. METHODS: One as cast (non-veneered) and two porcelain veneered Co-Cr specimens layered with and without tungsten(W)-metal conditioner were manufactured and analysed. Electron backscatter diffraction was used to determine the crystal structures and grain size across the porcelain-fused-to-metal interface. RESULTS: No difference was found in the microstructure of the alloy in both with and without W-metal conditioner. For the porcelain fired specimens, disparately sized granular structures were observed adjacent to the metal-porcelain interfaces compared to the bulk of the metal. Ellipsoid shaped grains at the alloy surface ranged between 1-11 µm in diameter and averaged 2.70 µm (SD: 2.17 µm) for the specimen layered with W-metal conditioner and 2.86 µm (SD: 1.85 µm) for the specimen layered without W-metal conditioner. Grains located in the bulk were > 200 µm with dendritic-like features. The depth of the fine grain structure adjacent to the surface had an average depth of 15 µm. The crystal structure of the surface layer was found to be predominantly hexagonal close-packed whereas the underlying bulk was a mixture of both face-centered cubic and hexagonal close-packed phases. For the as cast specimen, similar large grains of over 200 µm was observed but exhibited no dendritic like features. In addition, no fine grains were observed at the surface region of the as cast alloy. CONCLUSION: Conventional porcelain firings altered the interfacial and bulk microstructure of the alloy while the presence of the W-metal conditioner had no influence on the underlying alloy microstructure.

Supplemental vitamin D3 and zilpaterol hydrochloride. II. Effect on calcium concentration, muscle fiber type, and calpain gene expression of feedlot steers.

Two hundred and ten Angus × Simmental steers (initial BW 314 ± 11 kg) were separated into heavy and light BW blocks and allotted evenly by BW to 6 treatments (3 heavy and 2 light pens per treatment) to determine the effect of supplemental vitamin D3: 0 IU (no D), 250,000 IU for 165 d (long-term D), or 5 × 10(6) IU for 10 d (short-term D) on plasma and muscle calcium concentrations and gene expression in steers fed either 0 (NZ) or 8.38 mg/kg (ZH) zilpaterol hydrochloride (ZH) daily for 21 d. Placebo or ZH was added to the diet 24 d, and short-term D was added 13 d before slaughter. Treatments were removed from all diets 3 d before slaughter. Plasma total calcium (Ca(2+)) was determined at study initiation, start of ZH and short-term D feedings, and at vitamin D3 and ZH withdrawal. Both plasma total and ionic Ca(2+) were determined when animals were sent to harvest. Longissimus muscle total and ionic Ca(2+) were determined in meat aged 7 and 4 d postmortem, respectively. When ZH was fed, long-term D decreased plasma total Ca(2+) at slaughter (P < 0.04). Short-term D increased (P < 0.01) plasma total and ionic Ca(2+) at slaughter regardless of ZH inclusion in the diet. Long- and short-term D, with or without ZH, did not affect (P > 0.28) LM total Ca(2+); however, both long- and short-term D increased LM ionic Ca(2+) when ZH was not fed (P < 0.01). Long-term D reduced LM ionic Ca(2+) when ZH was fed (P < 0.02). Neither long- nor short-term D affected PPARα or δ gene expression (P = 0.19) whether or not ZH was fed. Expression of MYH1 and 2A (P < 0.05) but not 2X (P = 0.21) was decreased in steers fed ZH. Long-term D had no effect on MYH2A expression (P = 0.21). Short-term D increased MYH2A expression when ZH was not fed (P < 0.03). Calpain mRNA tended to be lower in steers fed ZH (P = 0.09), but was not affected by long- or short-term D regardless of whether or not ZH was fed (P = 0.39). Expression of calpastatin did not differ with vitamin D supplementation (P = 0.35). In conclusion, ZH decreased oxidative myosin expression, and when combined with long-term D, ZH decreased LM ionic Ca(2+). Moreover, vitamin D3 supplementation did not increase calpain mRNA. These results help explain why vitamin D3 does not improve tenderness in steers fed ZH.

Silver solder "tattoo," a novel form of oral pigmentation identified with the use of field emission scanning electron microscopy and electron dispersive spectrography.

OBJECTIVE: The aim of this study was to investigate the use of field emission scanning electron microscopy and electron dispersive spectrography (SEM-EDS) to identify silver solder "tattoo." STUDY DESIGN: SEM-EDS was used to analyze material present in the connective tissue of a patient who presented with bilateral pigmentation of the mandibular lingual gingiva adjacent to the first molars. No dental restorations were present. RESULTS: SEM-EDS analysis identified silver, with no evidence of tin, copper, or mercury. The patient was wearing an orthodontic appliance where brackets had been soldered to the archwire with silver solder. It is hypothesed that the solder underwent electrolytic corrosion with subsequent regrouping of silver ions in the submucosa leading to blue-gray discoloration. CONCLUSION: Spectrography proved to be a powerful diagnostic tool in identifying the metal within the oral mucosa. Attention is drawn to this newly described lesion, which should be included as a differential diagnosis for pigmented oral mucosal lesions.

Dental alloys used for crown and bridge restorations by dental technicians in New Zealand.

OBJECTIVE: To determine the range and elemental composition of alloys used for PFM and crown-and-bridge restorations by New Zealand dental laboratories, and to understand the reasons for their selection. MATERIALS AND METHODS: Two waves of data collection were carried out via post and telephone interview. The source population was dental laboratories advertised with the Yellow Pages Group in 2007/2008. RESULTS: A total of 83 out of 109 laboratories (76.1%) responded. Of those, 35 laboratories (42.1%) reported producing fixed-prosthodontic restorations. The range of alloy types (consisting of high noble, noble and base-metal alloys), brand names (55 products) and manufacturers was determined, along with the reasons for their selection. Ten international dental alloy manufacturers were identified as being used, with the leading manufacturer being Ivoclar-Vivadent (40.9%), followed by Argen (25.3%). Most laboratories select their alloys based on price and physical properties. The average laboratory carries three to four alloy products. CONCLUSION: Alloy selection by dentists and dental technicians is strongly influenced by economic factors. While the study identified the range of alloys being used for fixed restorations in terms of alloy type and brand name, further research is needed to determine the proportions of fixed restorations produced from high noble, noble and base metal alloys, together with dental practitioners' attitudes to, and preferences in, alloy selection.

Elemental composition of imported porcelain-fused-to-metal crowns--a pilot study.

OBJECTIVES: To identify any potentially toxic elements in porcelain-fused-to-metal (PFM) crowns and a bridge manufactured in China. MATERIALS AND METHODS: Eight PFM crowns and part of a bridge were sourced from China for testing. They were given a typical glaze firing cycle prior to scanning electron microscope analysis. Electron dispersive spectroscopic spot and mapping analysis was carried out on the porcelain/metal collar interface areas in order to determine their elemental composition and distribution. RESULTS: No toxic elements were detected. The alloy used in the crowns was a nickel-chromium base metal, and that in the bridge was a gold-palladium noble alloy. The veneering porcelain was similar to a standard dental veneering porcelain. CONCLUSIONS: Within the limitations of the testing method and small sample size, no toxic elements were detected.

Developmental changes in insulin-like growth factor (IGF)-I and -II mRNA abundance in extra-embryonic membranes and small intestine of avian embryos.

OBJECTIVE: Numerous researchers have evaluated the insulin-like growth factors (IGF) influence on mammalian fetal development. Although IGF has been explored in the avian system, questions remain on the role of IGF in avian development. Therefore, the current study evaluated the mRNA abundance of IGF in the amnion and allantoic membranes and developing small intestine in the chicken, duck, and turkey during the incubation and post-hatch period. DESIGN: Broiler, duck, and turkey eggs were incubated with small intestinal, allantoic, and amniotic membranes collected in the final days of incubation and 1 week post-hatch. RNA was extracted using Trizol and qRT-PCR was utilized to compare differences during embryo development within and across species. RESULTS: The expression of the IGF mRNA varied between species in the final days of incubation in the amniotic and allantoic membranes. The turkey had higher (0.38-1.72 log) transcript abundance of IGF-I and IGF-II in the amnion and allantois compared to the chicken and duck. Evaluating the mRNA abundance within the chicken duodenum, jejunum, and ileum, the duodenum had the lowest expression of IGF-I and IGF-II (P<0.05) at day -4 of incubation compared to the jejunum and ileum. Focusing on differences in jejunal IGF expression among the three species, the turkey had the lowest IGF-I abundance at day -4 of incubation and highest IGF-I abundance at day of hatch (P<0.05). Transcript abundance of both IGF-II and IGF-R was highest in the turkey at day of hatch and day 1 post-hatch compared to the duck and chicken. The whole tissue versus the mucosal expression of the IGF mRNA abundance was evaluated during the post-hatch period. Duodenal, jejunal, and ileal segments had higher IGF-I transcript abundance (P<0.05) at day 1, day 3, and day of hatch, respectively. No differences were observed between segment and mucosa for IGF-II in the post-hatch period. The duodenal and jejunal mucosa IGF-R transcript abundance was greater (P<0.05) at day of hatch compared to the intestinal segment. The duck IGF mRNA in the jejunal mucosa was higher than the whole segment and decreased from day of hatch to day 3 post-hatch while the IGF mRNA abundance increased in the whole segment during the same time period. The turkey IGF-I transcript abundance decreased in both the segment and mucosa following hatch while the IGF-II mRNA expression increased by 1.5 logs from hatch to day 1 post-hatch. CONCLUSION: The transcript abundance of the IGF axis in the extra-embryonic membranes and gastrointestinal tissue of the developing chicken, duck, and turkey are influenced by embryonic age and species. A better understanding of the IGF axis in the small intestine during embryonic development may allow for increasing the optimal growth of both the gastrointestinal tract and the neonate.

Biomechanical approach to human bitemark reconstruction.

UNLABELLED: This paper investigates the changes in upper and lower dental bite records that occur when the anterior teeth occlude into a three-dimensional rather than a flat object. METHODS: anterior bite registrations were obtained from 20 volunteers with full and unrestored dentitions. As a three- dimensional, life-like bite target we cast a silicone replica from the impression of an actual arm, fitted with a rigid bony interior. Each participant was asked to bite into a single layer of softened bite registration wax wrapped around the same location on the fake arm, as well as into a flat wafer of the same material. Upper and lower bite registrations were then scanned in the same location on a flat bed scanner. We analysed the sizes of the different bite marks by means of landmark- and semi-landmark analysis to calculate Procrustes distances between tooth outlines. In order to analyse shape variation between the two types of bite registration we carried out principal components analyses on the partial warp scores. These were derived from partial Procrustes coordinates aligned by means of thin-plate spline decomposition based on a bending energy matrix. Our results show that there are significant differences in the shape of the upper or lower teeth when they occlude into a flat or three- dimensional target. We conclude that the use of a traditional flat bite registration in human bitemark reconstruction and analysis has to be seriously questioned.

Analysis of gene expression during the onset of muscle hypertrophy in callipyge lambs.

The callipyge mutation causes postnatal muscle hypertrophy in heterozygous lambs that inherit a paternal callipyge allele (+/CLPG). Our hypothesis was that the up-regulation of one or both of the affected paternally expressed genes (DLK1 or PEG11) initiates changes in biochemical and physiological pathways in skeletal muscle to induce hypertrophy. The goal of this study was to identify changes in gene expression during the onset of muscle hypertrophy to identify the pathways that are involved in the expression of the callipyge phenotype. Gene expression was analysed in longissimus dorsi total RNA from lambs at 10, 20, and 30 days of age using the Affymetrix Bovine Expression Array. An average of 40.6% of probe sets on the array was detected in sheep muscle. Data were normalized and analysed using a two-way anova for genotype and age effects with a false discovery rate of 0.10. From the anova, 13 genes were significant for the effect of genotype and 13 were significant for effect of age (P < 0.10). No significant age-by-genotype interactions were detected (P > 0.10). Of the 13 genes indicating an effect of genotype, quantitative PCR assays were developed for all of them and tested on a larger group of animals from 10 to 200 days of age. Nine genes had significantly elevated transcript levels in callipyge lambs. These genes included phosphofructokinase, a putative methyltransferase protein, a cAMP phosphodiesterase, and the transcription factor DNTTIP1.

Influence of the bonder on the adhesion of porcelain to machined titanium as determined by the strain energy release rate.

OBJECTIVE: To determine the adhesion at the titanium-porcelain interface using a fracture mechanics approach, and to investigate the bonding mechanism using SEM. METHODS: Specimens of five different titanium-porcelain and one base metal-porcelain bonding systems were prepared for a four-point bending interfacial delaminating test on a universal testing machine. The pre-cracked specimen was subjected to load and the strain energy release rate (G, J/m(2)) was calculated from the critical load to induce stable crack extension in each system. The interface for the various materials was investigated in an SEM and compared. RESULTS: The titanium-porcelain with Gold Bonder showed the highest G-value (72.39+/-13.21J/m(2)) among the groups whilst titanium-porcelain with cross-cut-bur preparation showed the lowest (5.78+/-1.39J/m(2)). The former was significantly higher than that of Wiron 99 (base-metal, BEGO, Germany) porcelain (40.01+/-6.67J/m(2)), a clinically accepted bonding system for many years. The G-values of porcelain fused to titanium-Rocatec, titanium-sandblasted and/or titanium-GC-Bonder were 10.81+/-1.49, 12.64+/-3.01 and 35.74+/-5.20J/m(2), respectively. SEM images of the interface fracture crack path for the different bonders enabled the mechanisms responsible for the differences in strain energy release rates to be appreciated. CONCLUSION: The strain energy release rate (G) of titanium-porcelain with a Gold Bonder interface layer was highest among the five different systems.