The Length of Diaphyseal Contact of Tapered Fluted Stems is Highly Dependent on Canal Morphology.

BACKGROUND: Diaphyseal fixation remains the mainstay of revision THA. The stability of diaphyseal fixation can be quantified by the extent of contact between the stem and the endosteal cortex. This is highly affected by the morphology of the proximal femur. The purpose of this study was to examine factors affecting diaphyseal contact in the revision THA and to identify preoperative predictors of adequate fixation. METHODS: Three-dimensional femur models were created from CT scans of 33 Dorr B and C femora. The proximal 120 mm of the femur was omitted to mimic proximal bone deficiency. A tapered fluted stem (3 degrees, 150 mm) model was virtually implanted after reaming of the medullary canal. The contact length between stem and endosteal cortex was measured, in addition to other variables. The relationship between variables was evaluated using Spearman's correlation, and logistic regression analysis was used to identify predictors of the contact length (P < .05). RESULTS: The contact length varied widely between specimens (66.5 ± 16.6 mm, range: 21-98 mm). Contact increased with the depth of the isthmus below the lesser trochanter (range: 55-155 mm; r2 = 0.473, P = .005) and the distance between the isthmus and the distal edge of the damage zone (range: -9 to 96 mm; r2 = 0.508, P = .002). Stepwise regression identified the reaming length, distance between fracture and the isthmus, and isthmus diameter as independent predictors of contact length (r = 0.643). CONCLUSIONS: Contact is limited in specimens where the isthmus is more proximally located. In these cases, supplementary fixation using plating and/or longer, curved prosthesis may be considered.

Metal concentrations in the blood and tissues after implantation of titanium growth guidance sliding instrumentation.

BACKGROUND: Growth guidance sliding treatment devices, such as Shilla (Medtronic, Minneapolis, MN USA) or LSZ-4D (CONMET, Moscow, Russia), used for the treatment of scoliosis in children who have high growth potential have unlocked fixtures that allow rods to slide during growth of the spine, which avoids periodical extensions. However, the probability of clinical complications associated with metallosis after implantation of such devices is poorly understood. The content of metal ions in the blood and tissues of pediatric patients treated for scoliosis using fusionless growth guidance sliding instrumentation has not yet been investigated. PURPOSE: The aim of the present study was to measure the content of metal ions in the blood and tissues surrounding the implanted growth guidance sliding LSZ-4D devices made of titanium alloy (Ti6Al4V), and to identify the incidence of metallosis-associated clinical complications in some patients with these devices. STUDY DESIGN: This is a one-center, case-control retrospective study. PATIENTS SAMPLE: The study group included 25 patients with high growth potential (22 females, 3 males; average age at primary surgery for scoliosis treatment is 11.4±1.2 years old) who had sliding growth guidance instrumentation LSZ-4D (CONMET) implanted on 13 (range: 10-16) spine levels for 6±2 years. The LSZ-4D device was made from titanium alloy Ti6Al4V and consisted of two rectangular section rods and fixture elements. Locked fixtures were used on one spinal level, whereas the others were unlocked (sliding). The control group consisted of 13 patients (12 females and 1 male; 11±1.2 years old) without any implanted devices. OUTCOME MEASURES: The content of Ti, Al, and V metal ions in the whole blood and tissues around the implanted device was measured. The incidences of metallosis-associated complications in the study group were recorded. METHODS: Metal ion content was measured by the inductively coupled mass spectrometry method on quadrupolar NexION 300D (PerkinElmer Inc, Shelton, CT, USA). RESULTS: Five of 25 patients in the study group developed metallosis-associated complications (two sinuses and three seroma in the lumbar part of the spine). Revisions were carried out in two of these patients. Ninety percent of the patients in the study group had increased content of Ti and V ions in the blood (2.8 and 4 times, respectively). Median content of Ti ions in soft tissues adjacentto implanted sliding device was more than 1,500-fold higher than that of the control group. These levels are much higher than previously reported for spinal instrumentation. CONCLUSIONS: Increased content of Ti and V ions in the blood and especially in tissues around the titanium growth guidance sliding device LSZ-4D accompanied by clinical manifestations (seroma and sinuses) indicates the importance of improving wear resistance of such instrumentation with the coatings and the necessity to exchange sliding instrumentation once the child is fully grown.

Analysis of retrieved growth guidance sliding LSZ-4D devices for early onset scoliosis and investigation of the use of nitinol rods for this system.

STUDY DESIGN: Analysis of volumetric wear loss of retrieved growth guidance sliding devices LSZ-4D for treatment of early onset scoliosis and laboratory in vitro wear test for comparison of wear resistance of alloys Nitinol, Ti, and cobalt chromium (CoCr). OBJECTIVE: To evaluate quantitatively the amount of wear debris from the sliding LSZ-4D device and to investigate the potential of using Nitinol for replacing Ti alloys in spinal instrumentation. To do that, wear resistance of Nitinol, Ti, and CoCr was compared. SUMMARY OF BACKGROUND DATA: There are little data regarding the amount of wear debris associated with growth guidance sliding devices for patients with early onset scoliosis and the wear resistance of superelastic Nitinol compared with Ti and CoCr. METHODS: Volumetric wear loss was measured on LSZ-4D devices made from titanium alloy Ti6Al4V and each consisted of 2 rectangular section (6 × 4 mm) rods and 40 ± 8 fixture elements (20 ± 4 hooks and 20 ± 4 clips) retrieved from 3 patients (implantation period, 3.5-5.8 yr). Images of wear scars were taken on Bruker interferometer microscope and incorporated into MATLAB software. Wear resistance of Nitinol, Ti, and CoCr was studied using reciprocation pin-on-disk wear test in bovine serum at 37°C ± 1°C. RESULTS: The volume wear rate of LSZ-4D device was found to be 12.5 mm per year from which 5 mm³ per year is the wear debris of the rod and 7.5 mm per year is the contribution of fixtures. Wear resistance of Nitinol is 100 times higher than that of Ti and comparable with that of CoCr. CONCLUSION: Application of wear-resistant coatings on Ti components in growth guidance sliding devices for the treatment of early onset scoliosis will be useful. High wear resistance of Nitinol combined with its superelastic and shape memory properties could make application of Nitinol rods for spinal instrumentation beneficial.