Effects of Gas Layer Thickness on Capillary Interactions at Superhydrophobic Surfaces.

Strongly attractive forces act between superhydrophobic surfaces across water due to the formation of a bridging gas capillary. Upon separation, the attraction can range up to tens of micrometers as the gas capillary grows, while gas molecules accumulate in the capillary. We argue that most of these molecules come from the pre-existing gaseous layer found at and within the superhydrophobic coating. In this study, we investigate how the capillary size and the resulting capillary forces are affected by the thickness of the gaseous layer. To this end, we prepared superhydrophobic coatings with different thicknesses by utilizing different numbers of coating cycles of a liquid flame spraying technique. Laser scanning confocal microscopy confirmed an increase in gas layer thickness with an increasing number of coating cycles. Force measurements between such coatings and a hydrophobic colloidal probe revealed attractive forces caused by bridging gas capillaries, and both the capillary size and the range of attraction increased with increasing thickness of the pre-existing gas layer. Hence, our data suggest that the amount of available gas at and in the superhydrophobic coating determines the force range and capillary growth.

Calcite Surfaces Modified with Carboxylic Acids (C2 to C18): Layer Organization, Wettability, Stability, and Molecular Structural Properties.

A fundamental understanding of the interactions between mineral surfaces and amphiphilic surface modification agents is needed for better control over the production and uses of mineral fillers. Here, we controlled the carboxylic acid layer formation conditions on calcite surfaces with high precision via vapor deposition. The properties of the resulting carboxylic acid layers were analyzed using surface-sensitive techniques, such as atomic force microscopy (AFM), contact angle measurements, angle resolved X-ray photoelectron spectroscopy (XPS), and vibrational sum-frequency spectroscopy. A low wettability was achieved with long hydrocarbon chain carboxylic acids such as stearic acid. The stearic acid layer formed by vapor deposition is initially patchy, but with increasing vapor exposure time, the patches grow and condense into a homogeneous layer with a thickness close to that expected for a monolayer as evaluated by AFM and XPS. The build-up process of the layer occurs more rapidly at higher temperatures due to the higher vapor pressure. The stability of the deposited fatty acid layer in the presence of a water droplet increases with the chain length and packing density in the adsorbed layer. Vibrational sum frequency spectroscopy data demonstrate that the stearic acid monolayers on calcite have their alkyl chains in an all-trans conformation and are anisotropically distributed on the plane of the surface, forming epitaxial monolayers. Vibrational spectra also show that the stearic acid molecules interact with the calcite surface through the carboxylic acid headgroup in both its protonated and deprotonated forms. The results presented provide new molecular insights into the properties of adsorbed carboxylic acid layers on calcite.

Effects of liquid surface tension on gas capillaries and capillary forces at superamphiphobic surfaces.

The formation of a bridging gas capillary between superhydrophobic surfaces in water gives rise to strongly attractive interactions ranging up to several micrometers on separation. However, most liquids used in materials research are oil-based or contain surfactants. Superamphiphobic surfaces repel both water and low-surface-tension liquids. To control the interactions between a superamphiphobic surface and a particle, it needs to be resolved whether and how gas capillaries form in non-polar and low-surface-tension liquids. Such insight will aid advanced functional materials development. Here, we combine laser scanning confocal imaging and colloidal probe atomic force microscopy to elucidate the interaction between a superamphiphobic surface and a hydrophobic microparticle in three liquids with different surface tensions: water (73 mN m-1), ethylene glycol (48 mN m-1) and hexadecane (27 mN m-1). We show that bridging gas capillaries are formed in all three liquids. Force-distance curves between the superamphiphobic surface and the particle reveal strong attractive interactions, where the range and magnitude decrease with liquid surface tension. Comparison of free energy calculations based on the capillary menisci shapes and the force measurements suggest that under our dynamic measurements the gas pressure in the capillary is slightly below ambient.

A rubberized impact absorbing pavement can reduce the head injury risk in vulnerable road users: A bicycle and a pedestrian accident case study.

OBJECTIVE: Vulnerable Road Users (VRU), including pedestrians and cyclists, are generally the least protected road users and are frequently missed in the planning process of preventive measures. Rubberized asphalt mixtures were originally developed as a possible environmentally friendly solution to recycle the End-of-Life Tires while making the pavements more durable. The objective of the current study was to explore the effects of increasing the rubber content of the common rubberized asphalt mixtures in reducing the head injuries risk for VRUs. METHOD: To achieve this purpose, four different sample series with 0, 14, 28, and 33 weight percent rubber in each were tested. A compressive test without permanent deformation and one with failure were performed on each sample series. The mechanical behavior of each set was modeled using a MAT_SIMPLIFIED_RUBBER material model in LS-Dyna and validated against a standard Head Injury Criterion (HIC) drop test. Ultimately, previously low-speed accident reconstructed cases, a bicycle and a pedestrian one, were used to assess the effect of varying the rubber content on reducing the head injury risk. RESULTS: In the bicycle accident case, the risk of skull fracture was reduced from 0.99 to 0.29 when comparing the non-rubberized asphalt mixture with the 33% rubber mixture. In the same accident case, the risk of concussion, evaluated using the logistic regression method, was reduced from 0.97 in the non-rubberized mixture to 0.81 in the 33% rubber mixture. The initial conditions, linear and rotational velocities, were lower for the pedestrian case compared to the bicycle case (the bicycle case was more severe compared to the pedestrian case), which led to lower strains in the pedestrian case. In the pedestrian accident case, the risk of skull fracture was reduced from 1.00 in the non-rubberized mixture to 0.63 in the 33% rubber mixture, while the risk of concussion was reduced from 0.64 to 0.07. CONCLUSION: The rubberized asphalt mixtures could reduce the head injury risk for the studied cases when the rubber content in the asphalt mixture increases.

Surface-Modified and Unmodified Calcite: Effects of Water and Saturated Aqueous Octanoic Acid Droplets on Stability and Saturated Fatty Acid Layer Organization.

A profound understanding of the properties of unmodified and saturated fatty acid-modified calcite surfaces is essential for elucidating their resistance and stability in the presence of water droplets. Additional insights can be obtained by also studying the effects of carboxylic acid-saturated aqueous solutions. We elucidate surface wettability, structure, and nanomechanical properties beneath and at the edge of a deposited droplet after its evaporation. When calcite was coated by a highly packed monolayer of stearic acid, a hydrophilic region was found at the three-phase contact line. In atomic force microscopy mapping, this region is characterized by low adhesion and a topographical hillock. The surface that previously was covered by the droplet demonstrated a patchy structure of about 6 nm height, implying stearic acid reorganization into a patchy bilayer-like structure. Our data suggest that during droplet reverse dispensing and droplet evaporation, pinning of the three-phase contact line leads to the transport of dissolved fatty carboxylic acid and possibly calcium bicarbonate Ca(HCO3)2 molecules to the contact line boundary. Compared to the surface of intrinsically hydrophobic materials, such as polystyrene, the changes in contact angle and base diameter during droplet evaporation on stearic acid-modified calcite are strikingly different. This difference is due to stearic acid reorganization on the surface and transport to the water-air interface of the droplet. An effect of the evaporating droplet is also observed on unmodified calcite due to dissolution and recrystallization of the calcite surface in the presence of water. In the case where a water droplet saturated with octanoic acid is used instead of water, the stearic acid-coated calcite remains considerably more stable. Our findings are discussed in terms of the coffee-ring effect.

Nanoscale Wear and Mechanical Properties of Calcite: Effects of Stearic Acid Modification and Water Vapor.

Understanding the wear of mineral fillers is crucial for controlling industrial processes, and in the present work, we examine the wear resistance and nanomechanical properties of bare calcite and stearic acid-modified calcite surfaces under dry and humid conditions at the nanoscale. Measurements under different loads allow us to probe the situation in the absence and presence of abrasive wear. The sliding motion is in general characterized by irregular stick-slip events that at higher loads lead to abrasion of the brittle calcite surface. Bare calcite is hydrophilic, and under humid conditions, a thin water layer is present on the surface. This water layer does not affect the friction force. However, it slightly decreases the wear depth and strongly influences the distribution of wear particles. In contrast, stearic acid-modified surfaces are hydrophobic. Nevertheless, humidity affects the wear characteristics by decreasing the binding strength of stearic acid at higher humidity. A complete monolayer coverage of calcite by stearic acid results in a significant reduction in wear but only a moderate reduction in friction forces at low humidity and no reduction at 75% relative humidity (RH). Thus, our data suggest that the wear reduction does not result from a lowering of the friction force but rather from an increased ductility of the surface region as offered by the stearic acid layer. An incomplete monolayer of stearic acid on the calcite surface provides no reduction in wear regardless of the RH investigated. Clearly, the wear properties of modified calcite surfaces depend crucially on the packing density of the surface modifier and also on the air humidity.

Wetting Transition on Liquid-Repellent Surfaces Probed by Surface Force Measurements and Confocal Imaging.

Superhydrophobic surfaces in the Cassie-Baxter wetting state retain an air layer at the surface which prevents liquid water from reaching into the porous surface structure. In this work we explore how addition of ethanol, which reduces the surface tension, influences the wetting properties of superhydrophobic and smooth hydrophobic surfaces. Wetting properties are measured by dynamic contact angles, and the air layer at the superhydrophobic surface is visualized by laser scanning confocal microscopy. Colloidal probe atomic force microscopy measurements between a hydrophobic microsphere and the macroscopic surfaces showed that the presence of ethanol strongly affects the interaction forces. When the macroscopic surface is superhydrophobic, attractive forces extending up to a few micrometers are observed on retraction in water and in 20 vol % ethanol, signifying the presence of a large and growing gas capillary. Submicrometer attractive forces are observed between the probe particle and a smooth hydrophobic surface, and in this case a smaller gas capillary is formed. Addition of ethanol results in markedly different effects between superhydrophobic and hydrophobic surfaces. In particular, we show that the receding contact angle on the superhydrophobic surface is of paramount importance for describing the interaction forces.

Direct Observation of Gas Meniscus Formation on a Superhydrophobic Surface.

The formation of a bridging gas meniscus via cavitation or nanobubbles is considered the most likely origin of the submicrometer long-range attractive forces measured between hydrophobic surfaces in aqueous solution. However, the dynamics of the formation and evolution of the gas meniscus is still under debate, in particular, in the presence of a thin air layer on a superhydrophobic surface. On superhydrophobic surfaces the range can even exceed 10 µm. Here, we report microscopic images of the formation and growth of a gas meniscus during force measurements between a superhydrophobic surface and a hydrophobic microsphere immersed in water. This is achieved by combining laser scanning confocal microscopy and colloidal probe atomic force microscopy. The configuration allows determination of the volume and shape of the meniscus, together with direct calculation of the Young-Laplace capillary pressure. The long-range attractive interactions acting on separation are due to meniscus formation and volume growth as air is transported from the surface layer.

Iceland spar calcite: Humidity and time effects on surface properties and their reversibility.

Understanding the complex and dynamic nature of calcite surfaces under ambient conditions is important for optimizing industrial applications. It is essential to identify processes, their reversibility, and the relevant properties of CaCO3 solid-liquid and solid-gas interfaces under different environmental conditions, such as at increased relative humidity (RH). This work elucidates changes in surface properties on freshly cleaved calcite (topography, wettability and surface forces) as a function of time (≤28 h) at controlled humidity (≤3-95 %RH) and temperature (25.5 °C), evaluated with atomic force microscopy (AFM) and contact angle techniques. In the presence of humidity, the wettability decreased, liquid water capillary forces dominated over van der Waals forces, and surface domains, such as hillocks, height about 7.0 Å, and trenches, depth about -3.5 Å, appeared and grew primarily in lateral dimensions. Hillocks demonstrated lower adhesion and higher deformation in AFM experiments. We propose that the growing surface domains were formed by ion dissolution and diffusion followed by formation of hydrated salt of CaCO3. Upon drying, the height of the hillocks decreased by about 50% suggesting their alteration into dehydrated or less hydrated CaCO3. However, the process was not entirely reversible and crystallization of new domains continued at a reduced rate.

Nanomechanical properties of human skin and introduction of a novel hair indenter.

The mechanical resistance of the stratum corneum, the outermost layer of skin, to deformation has been evaluated at different length scales using Atomic Force Microscopy. Nanomechanical surface mapping was first conducted using a sharp silicon tip and revealed that Young׳s modulus of the stratum corneum varied over the surface with a mean value of about 0.4GPa. Force indentation measurements showed permanent deformation of the skin surface only at high applied loads (above 4µN). The latter effect was further demonstrated using nanomechanical imaging in which the obtained depth profiles clearly illustrate the effects of increased normal force on the elastic/plastic surface deformation. Force measurements utilizing the single hair fiber probe supported the nanoindentation results of the stratum corneum being highly elastic at the nanoscale, but revealed that the lateral scale of the deformation determines the effective elastic modulus.This result resolves the fact that the reported values in the literature vary greatly and will help to understand the biophysics of the interaction of razor cut hairs that curl back during growth and interact with the skin.

Influence of surface topography on adhesive and long-range capillary forces between hydrophobic surfaces in water.

We report on the interactions between a hydrophobic probe particle and surfaces with nanoscopic surface features. These surfaces have been prepared by spin-coating of nanoparticles and by polishing. The surface topography was characterized by AFM, using the methods of high-resolution imaging, low-resolution imaging using the probe particle, and by the rolling ball method. The spin-coated surfaces can be characterized as nanostructured due to the high density of nanoparticles that on a short length scale provides a regular pattern of crevices and hills. On these surfaces a larger waviness is also distinguished. In contrast, the polished surfaces display sharp nanoscopic peaks and hardly any crevices. In all cases the dominant force at short separations was found to be a capillary attraction due to the formation of an air/vapor condensate. Our data show that the large-scale waviness of the surface does not significantly influence the range and magnitude of the capillary attraction, but large local variations in these quantities are found. The large variation in adhesion force corresponds to a small variation in local contact angle of the capillary condensate at the surfaces. The report discusses how the nature of the surface topographical features influences the capillary attraction by influencing the local contact angle and by pinning of the three-phase contact line. The effect is clearly dependent on whether the surface features exist in the form of crevices or as extending ridges.

Influence of wetting and dispersing agents on the interaction between talc and hydrophobic particles.

The interactions between a natural talc surface and a model hydrophobic particle have been investigated in aqueous solutions by employing the atomic force microscopy (AFM) colloidal probe technique. The results demonstrate the presence of long-range attractive forces due to bridging via preadsorbed or induced bubbles/cavities. Due to the natural heterogeneity of talc, and the stochastic nature of the bubble bridging process, the variability in the range and magnitude of the attraction is larger than that for cases when other interactions predominate or than that when only model surfaces are used. Addition of poly(acrylic acid), a common dispersing agent, did not affect the measured forces. Thus, we conclude that poly(acrylic acid) does not adsorb to the basal plane of talc. In sharp contrast, addition of Pluronic PE6400, a nonionic triblock polymer used as wetting agent, resulted in complete removal of the bubble-induced attractive force. Instead, a short-range steric repulsion is the dominating feature. Clearly, Pluronic PE6400 is able to displace air bubbles from the surface and prevent their formation when the particles come into contact. These are suggested to be important features of efficient wetting agents.

Interaction forces between talc and pitch probed by atomic force microscopy.

Colloidal wood resin components present in pulp are collectively called "pitch". The presence of pitch may cause severe problems due to deposits in and on the paper machine. There is thus a need for controlling pitch aggregation and adsorption. To be able to develop more efficient pitch control systems, one needs to develop the understanding of pitch-pitch interactions and of the interactions between pitch and other materials. With this general goal in mind, we present methods for preparing geometrically well-defined pitch particles attached to atomic force microscopy tips. This has enabled us to investigate the interactions between pitch and talc, an additive commonly used for pitch control. We have used model pitch particles consisting of one component only (abietic acid), a mixture of components (collophonium), and particles prepared from real pitch deposits. We show that the forces acting between pitch and talc are attractive and, once the initial approach is made, exert this attraction out to large distances of separation. We present evidence that the formation of bridging air bubbles or cavities is responsible for this interaction.