RESUMO
Brillouin optical time-domain analysis requires a pulsed pump to obtain a distributed Brillouin gain spectrum (BGS) containing environmental information, whose width corresponds to spatial resolution (SR). We propose a rising edge demodulation (RED) algorithm acting on Brillouin information generated by a transient pump pulse (
RESUMO
A new technique for the fast implementation of Brillouin optical time-domain reflectometry has been proposed and demonstrated with the optical chirp chain (OCC) reference wave. By using the fixed bandpass filter and envelope detection, the spontaneous Brillouin spectrum can be online demodulated in the time domain for truly distributed, one-end access and fast measurement. The measurement time is only limited by the pulse repetition rate and averaging times. For a 400 m single-mode fiber, a 31.58Hz strain vibration on a 2 m fiber segment is measured for a wide dynamic range (â¼3200µÎµ) with an equivalent sampling rate of 200Hz when 200 times of averaging is performed. Furthermore, the performance on the measurement accuracy is investigated with different OCC frequency spans and durations.
RESUMO
A fast Brillouin optical time-domain analysis (BOTDA) sensor has been proposed and experimentally demonstrated based on the frequency-agile and compressed-sensing technique. The proposed scheme employs a data-adaptive sparse base obtained by the principle component analysis algorithm, enabling the sparse representation of Brillouin spectrum. Then, it can be reconstructed successfully with random frequency sampling and orthogonal matching-pursuit algorithms. In the experiment, the Brillouin gain spectrum (BGS) is mapped by the conventional fast BOTDA, where the frequency step and span are 4 MHz and 500 MHz, respectively. By using compressed-sensing technology, the BGS is successfully recovered with 37 random frequency samples, the number of which is only 30% of the full data. With fewer sampling frequencies, the compressed-sensing technology is able to improve the sensing performance of the conventional fast BOTDA, including a 3.3-time increase in sampling rate and 70% reduction in data storage.
RESUMO
Distributed long-range Brillouin optical time domain analysis (BOTDA) is an extremely time-consuming sensing scheme, which requires frequency mapping of the Brillouin spectrum and a large number of average times. Here, we propose a fast long-range BOTDA based on the optical chirp chain (OCC) probe wave and Brillouin loss scheme. The OCC-modulated probe wave is enabled by cascading fast-frequency-changing microwave chirp segments head-to-tail, which covers a large frequency range around the anti-Stokes frequency relative to the pump wave. The combination of the OCC technique and Brillouin loss scheme provides several advantages, i.e., fast measurement, a high Brillouin threshold, no additional amplification scheme, and freedom from the nonlocal effect. In the experiment, 6 m spatial resolution, 3.2 s measurement time, and 3 MHz measurement precision were achieved over a 150 km single-mode fiber.
RESUMO
Brillouin optical time-domain analysis (BOTDA) requires frequency mapping of the Brillouin spectrum to obtain environmental information (e.g., temperature or strain) over the length of the sensing fiber, with the finite frequency-sweeping time-limiting applications to only static or slowly varying strain or temperature environments. To solve this problem, we propose the use of an optical chirp chain probe wave to remove the requirement of frequency sweeping for the Brillouin spectrum, which enables distributed ultrafast strain measurement with a single pump pulse. The optical chirp chain is generated using a frequency-agile technique via a fast-frequency-changing microwave, which covers a larger frequency range around the Stokes frequency relative to the pump wave, so that a distributed Brillouin gain spectrum along the fiber is realized. Dynamic strain measurements for periodic mechanical vibration, mechanical shock, and a switch event are demonstrated at sampling rates of 25 kHz, 2.5 MHz and 6.25 MHz, respectively. To the best of our knowledge, this is the first demonstration of distributed Brillouin strain sensing with a wide-dynamic range at a sampling rate of up to the MHz level.
RESUMO
In distributed Brillouin optical fiber sensor when the length of the perturbation to be detected is much smaller than the spatial resolution that is defined by the pulse width, the measured Brillouin gain spectrum (BGS) experiences two or multiple peaks. In this work, we propose and demonstrate a technique using differential pulse pair Brillouin optical time-domain analysis (DPP-BOTDA) based on double-peak BGS to enhance small-scale events detection capability, where two types of single mode fiber (main fiber and secondary fiber) with 116 MHz Brillouin frequency shift (BFS) difference have been used. We have realized detection of a 5-cm hot spot at the far end of 24-km single mode fiber by employing a 50-cm spatial resolution DPP-BOTDA with only 1GS/s sampling rate (corresponding to 10 cm/point). The BFS at the far end of 24-km sensing fiber has been measured with 0.54 MHz standard deviation which corresponds to a 0.5°C temperature accuracy. This technique is simple and cost effective because it is implemented using the similar experimental setup of the standard BOTDA, however, it should be noted that the consecutive small-scale events have to be separated by a minimum length corresponding to the spatial resolution defined by the pulse width difference.
RESUMO
We present a slope-assisted BOTDA system based on the vector stimulated Brillouin scattering (SBS) and frequency-agile technique (FAT) for the wide-strain-range dynamic measurement. A dimensionless coefficient K defined as the ratio of Brillouin phase-shift to gain is employed to demodulate the strain of the fiber, and it is immune to the power fluctuation of pump pulse and has a linear relation of the frequency detuning for the continuous pump and Stokes waves. For a 30ns-square pump pulse, the available frequency span of the K spectrum can reach up to 200MHz, which is larger than fourfold of 48MHz-linewidth of Brillouin gain spectrum. For a single-slope assisted BOTDA, dynamic strain measurement with the maximum strain of 2467.4µÎµ and the vibration frequency components of 10.44Hz and 20.94Hz is obtained. For a multi-slope-assisted BOTDA, dynamic measurement with the strain variation up to 5372.9µÎµ and the vibration frequency components of 5.58Hz and 11.14Hz is achieved by using FAT to extend the strain range.
RESUMO
We propose and demonstrate a dynamic Brillouin optical fiber sensing based on the multi-slope assisted fast Brillouin optical time-domain analysis (F-BOTDA), which enables the measurement of a large strain with real-time data processing. The multi-slope assisted F-BOTDA is realized based on the double-slope demodulation and frequency-agile modulation, which significantly increases the measurement range compared with the single- or double- slope assisted F-BOTDA, while maintaining the advantage of fast data processing and being suitable for real-time on-line monitoring. A maximum strain variation up to 5000µÎµ is measured in a 32-m fiber with a spatial resolution of ~1m and a sampling rate of 1kHz. The frequency of the strain is 12.8Hz, which is limited by the rotation rate of the motor used to load the force on the fiber. Furthermore, the influence of the frequency difference between two adjacent probe tones on the measurement error is studied theoretically and experimentally for optimization. For a Brillouin gain spectrum with a 78-MHz width, the optimum frequency difference is ~40MHz. The measurement error of Brillouin frequency shift is less than 3MHz over the whole measurement range (241MHz).
