Sandwich-Structured Mxene/Waste Polyurethane Foam Composites For Highly Efficient Electromagnetic Interference, Infrared Shielding and Joule Heating.

Electromagnetic interference (EMI) shielding and infrared (IR) stealth materials have attracted increasing attention owing to the rapid development of modern communication and military surveillance technologies. However, to realize excellent EMI shielding and IR stealth performance simultaneously remains a great challenge. Herein, a facile strategy is demonstrated to prepare high-efficiency EMI shielding and IR stealth materials of sandwich-structured MXene-based thin foam composites (M-W-M) via filtration and hot-pressing. In this composite, the conductive Ti3C2Tx MXene/cellulose nanofiber (MXene/CNF) film serves as the outer layer, which reflects electromagnetic waves and reduces the IR emissivity. Meanwhile, the middle layer is composed of a porous waste polyurethane foam (WPUF), which not only improves thermal insulation capacity but also extends electromagnetic wave propagation paths. Owing to the unique sandwich structure of "film-foam-film", the M-W-M composite exhibits a high EMI shielding effectiveness of 83.37 dB, and in the meantime extremely low emissivity (22.17%) in the wavelength range of 7-14 µm and thermal conductivity (0.19 W m-1 K-1), giving rise to impressive IR stealth performance at various surrounding temperatures. Remarkably, the M-W-M composite also shows excellent Joule heating properties, capable of maintaining the IR stealth function during Joule heating.

Facile fabrication of 3D Janus foams of electrospun cellulose nanofibers/rGO for high efficiency solar interface evaporation.

Solar-powered interfacial evaporation is one of the most efficient state-of-the-art technologies for producing clean water via desalination. Herein, we report a novel bio-based nanofibrous foam for high efficiency solar interface evaporation. To this end, a hybrid membrane of cellulose nanofibers/graphene oxide (GO) is first fabricated by electrospinning coupled with in situ layer-by-layer self-assembly technique. After that, the membrane is subjected to a foaming process in an aqueous NaBH4, which effectively transforms the 2D membrane into a 3D foam. This structure can improve the photothermal conversion efficiency and also facilitate the water transport at the gas-water interface. In the meantime, the GO is converted to the reduced GO (rGO) with a higher light absorption efficiency. Finally, one side of the foam is hydrophobically modified via spray-coating with a fluorocarbon resin (FR) to obtain the Janus type 3D foam, namely FR@EC/rGO. The resultant 3D foam combines the functions of solar energy absorption in the upper layer and water pumping capability in the lower layer. It exhibits an extraordinary solar vapor conversion efficiency of 94.2 % and a fast evaporation rate of 1.83 kg m-2 h-1, showing high potential in future seawater desalination.

Facile fabrication of three-dimensional nanofibrous foams of cellulose@g-C3N4@Cu2O with superior visible-light photocatalytic performance.

In this work, a unique three-dimensional nanofibrous foam of cellulose@g-C3N4@Cu2O was prepared via electrospinning followed by a foaming process. A cellulose solution in DMAc/LiCl containing g-C3N4 and CuSO4 was applied for electrospinning, while aqueous alkali was used as the coagulation bath. The solidification of electrospun cellulose/g-C3N4 nanofibers would be accompanied with in-situ formation of Cu(OH)2 nanoparticles. Interestingly, the hydrogen gas (H2) generated from NaBH4 could transform the two-dimensional membrane into a three-dimensional foam, leading to the increased specific surface area and porosity of the material. Meanwhile, the Cu(OH)2 nanoparticles attached on the electrospun nanofibers were reduced to Cu2O to form a p-n heterostructure between Cu2O and g-C3N4. The as-prepared cellulose@g-C3N4@Cu2O foam exhibited a high degradation efficiency (99.5 %) for the dye of Congo Red under visible light radiation. And ·O2- was discovered to be the dominant reactive species responsive for dye degradation. Moreover, the cellulose@g-C3N4@Cu2O could maintain its initial degradation efficiency even after seven cycles of reuse, suggesting the excellent stability and cycling performance.

Mechanically Strong and Electrically Conductive Polyethylene Oxide/Few-Layer Graphene/Cellulose Nanofibrils Nanocomposite Films.

In this work, a cellulose nanofibrils (CNFs)/few-layer graphene (FLG) hybrid is mechanically stripped from bamboo pulp and expanded graphene (EG) using a grinder. This strategy is scalable and environmentally friendly for high-efficiency exfoliation and dispersion of graphene in an aqueous medium. The in situ-generated CNFs play a key role in this process, acting as a "green" dispersant. Next, the obtained CNFs-FLG is used as a functional filler in a polyoxyethylene (PEO) matrix. When the composition of CNFs-FLG is 50 wt.%, the resultant PEO/CNFs-FLG nanocomposite film exhibits a Young's modulus of 1.8 GPa and a tensile strength of 25.7 MPa, showing 480% and 260% enhancement as compared to those of the pure PEO film, respectively. Remarkably, the incorporation of CNFs-FLG also provides the nanocomposite films with a stunning electrical conductivity (72.6 S/m). These attractive features make PEO/CNFs-FLG nanocomposite films a promising candidate for future electronic devices.

Polyethylenimine-Functionalized Nanofiber Nonwovens Electrospun from Cotton Cellulose for Wound Dressing with High Drug Loading and Sustained Release Properties.

Electrospun cellulose nanofiber nonwovens have shown promise in wound dressing owing to the highly interconnected pore structure, high hydrophilicity coupled with other coveted characteristics of biodegradability, biocompatibility and renewability. However, electrospun cellulose wound dressings with loaded drugs for better wound healing have been rarely reported. In this study, a novel wound dressing with a high drug loading capacity and sustained drug release properties was successfully fabricated via electropinning of cellulose followed by polyethylenimine (PEI)-functionalization. Remarkably, the grafted PEI chains on the surface of electrospun cellulose nanofibers provided numerous active amino groups, while the highly porous structure of nonwovens could be well retained after modification, which resulted in enhanced adsorption performance against the anionic drug of sodium salicylate (NaSA). More specifically, when immersed in 100 mg/L NaSA solution for 24 h, the as-prepared cellulose-PEI nonwoven displayed a multilayer adsorption behavior. And at the optimal pH of 3, a high drug loading capacity of 78 mg/g could be achieved, which was 20 times higher than that of pristine electrospun cellulose nonwoven. Furthermore, it was discovered that the NaSA-loaded cellulose-PEI could continuously release the drug for 12 h in simulated body fluid (SBF), indicating the versatility of cellulose-PEI as an advanced wound dressing with drug carrier functionalities.

One-pot superhydrophilic surface modification of waste polyurethane foams for high-efficiency oil/water separation.

Despite of the fact that polymers have brought tremendous convenience to human life, they have also inevitably caused considerable environmental pollution after their service life. Therefore, a feasible strategy that can effectively recycle waste polymers and endow them with high added value is much desired. Superwetting materials have shown great promise in oily wastewater treatment because of their high oil/water separation efficiency. However, most of these materials present some limitations, such as complex preparation procedures and poor salt tolerance, which hamper their practical applications. In this study, an iron hydroxide@polydopamine@waste polyurethane foam (Fe(OH)3@PDA@WPU) was synthesized via a facile and mild "one-pot" reaction. During this process, polymerization of dopamine and in situ growth of Fe(OH)3 were simultaneously realized, and the resultant PDA and Fe(OH)3 nanoparticles were firmly attached to the surface of WPU. Due to the abundant hydrophilic groups from PDA and Fe(OH)3 coupled with the surface roughness created by Fe(OH)3 nanoparticles, the surface properties of the foam could be changed from hydrophobic to superhydrophilic. Remarkably, the Fe(OH)3@PDA@WPU was capable of separating various oil/water mixtures even under some severe conditions (e.g. erosion in a saturated sodium chloride solution and longtime sonication), demonstrating high potential in marine oily sewage treatment. Moreover, this work also paved a new path for reducing the negative impact of waste polymer foams on our environment, and in the meantime realizing their high value utilization.

Iron-Loaded Carbon Aerogels Derived from Bamboo Cellulose Fibers as Efficient Adsorbents for Cr(VI) Removal.

A unique iron/carbon aerogel (Fe/CA) was prepared via pyrolysis using ferric nitrate and bamboo cellulose fibers as the precursors, which could be used for high-efficiency removal of toxic Cr(VI) from wastewaters. Its composition and crystalline structures were characterized by FTIR, XPS, and XRD. In SEM images, the aerogel was highly porous with abundant interconnected pores, and its carbon-fiber skeleton was evenly covered by iron particles. Such structures greatly promoted both adsorption and redox reaction of Cr(VI) and endowed Fe/CA with a superb adsorption capacity of Cr(VI) (182 mg/g) with a fast adsorption rate (only 8 min to reach adsorption equilibrium), which outperformed many other adsorbents. Furthermore, the adsorption kinetics and isotherms were also investigated. The experiment data could be much better fitted by the pseudo-second-order kinetics model with a high correlating coefficient, suggesting that the Cr(VI) adsorption of Fe/CA was a chemical adsorption process. Meanwhile, the Langmuir model was found to better describe the isotherm curves, which implied the possible monolayer adsorption mechanism. It is noteworthy that the aerogel adsorbent as a bulk material could be easily separated from the water after adsorption, showing high potential in real-world water treatment.

A TiO2 Coated Carbon Aerogel Derived from Bamboo Pulp Fibers for Enhanced Visible Light Photo-Catalytic Degradation of Methylene Blue.

Carbon aerogels (CA) derived from bamboo cellulose fibers were coupled with TiO2 to form CA/TiO2 hybrids, which exhibited extraordinary performance on the photo-catalytic degradation of methylene blue (MB). The structure and morphology of CA/TiO2 were characterized by field emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and Raman spectrum. The CA displayed a highly porous and interconnected three-dimensional framework structure, while introducing the catalytic active sites of TiO2 onto the aerogel scaffold could remarkably enhance its photo-catalytic activity. The adsorption and photo-catalytic degradation of MB by the CA/TiO2 hybrid were investigated. The maximum adsorption capacity of CA/TiO2 for MB was 18.5 mg/g, which outperformed many similar materials reported in the literature. In addition, compared with other photo-catalysts, the present CA/TiO2 demonstrated superior photo-catalytic performance. Almost 85% of MB in 50 mL solution with a MB concentration of 10 mg/L could be effectively degraded by 15 mg CA/TiO2 in 300 min.

Biodegradable all-cellulose composite membranes for simultaneous oil/water separation and dye removal from water.

While of enormous scientific interests, the super-wetting materials capable of one-step separation of oils and dyes from water are rare on the market. Besides, the disposal of the used materials themselves is still a challenge, mainly ascribed to their non-biodegradation. Herein, we report an all-cellulose composite membrane that can simultaneously remove oil and dye from water. The membrane was fabricated via a simple dip-coating process during which the filter paper was coated by a cellulose hydrogel layer. This cellulose hydrogel coating was discovered to play an essential role in the separation of oil/water emulsion. Meanwhile, the incorporation of citric acid remarkably improved the mechanical and adsorption properties of the membrane as it served as both the crosslinking agent and the active species for methylene blue adsorption. This work demonstrated a new strategy on the development of fully biodegradable materials for both high-efficiency oil/water separation and dye removal.

Honeycomb-structured carbon aerogels from nanocellulose and skin secretion of Andrias davidianus for highly compressible binder-free supercapacitors.

Nanocellulose-derived carbon is a promising material in energy storage because of its sustainability, low environmental impact, and large specific surface area. Herein, the skin secretion of Andrias davidianus (SSAD) is applied for the first time as the bio-nitrogen source to dope carbon aerogels from nanocellulose. Cellulose nanocrystal (CNC) is discovered to be very effective to address the dispersion problem of SSAD in water. After being homogeneously mixed with cellulose nanofiber (CNF), honeycomb-structured nanofibrous carbon aerogels are obtained via unidirectional freeze-drying of the SSAD/CNC/CNF mixture followed by high-temperature carbonization. Impressively, unlike those fragile carbon aerogels in many early works, the present ones exhibit outstanding elasticity in repeated compression and release tests. Moreover, a symmetric binder-free supercapacitor is assembled from the carbon aerogels, which exhibits improved electrochemical capacitive properties and cycling stability. And even after 500 compression and release cycles, the supercapacitor can still maintain high capacitive performance, indicating its superiorities in durability and electrochemical stability.