Analysis of rheological properties of bone cements.

The rheological properties of three commercially available bone cements, CMW 1, Palacos R and Cemex ISOPLASTIC, were investigated. Testing was undertaken at both 25 and 37 degrees C using an oscillating parallel plate rheometer. Results showed that the three high viscosity cements exhibited distinct differences in curing rate, with CMW 1 curing in 8.7 min, Palacos R and Cemex ISOPLASTIC in 13 min at 25 degrees C. Furthermore it was found that these curing rates were strongly temperature dependent, with curing rates being halved at 37 degrees C. By monitoring the change of viscosity with time over the entire curing process, the results showed that these cements had differing viscosity profiles and hence exhibit very different handling characteristics. However, all the cements reached the same maximum viscosity of 75 x 10(3) Pa s. Also, the change in elastic/viscous moduli and tan delta with time, show the cements changing from a viscous material to an elastic solid with a clear peak in the viscous modulus during the latter stages of curing. These results give valuable information about the changes in rheological properties for each commercial bone cement, especially during the final curing process.

Reduced adherence of Candida to silane-treated silicone rubber.

Silicone rubber is widely used in the construction of medical devices that can provide an essential role in the treatment of human illness. However, subsequent microbial colonization of silicone rubber can result in clinical infection or device failure. The objective of this study was to determine the effectiveness of a novel silane-treated silicone rubber in inhibiting microbial adherence and material penetration. Test material was prepared by a combination of argon plasma discharge treatment and fluorinated silane coupling. Chemicophysical changes were then confirmed by X-ray photoelectron spectroscopy, contact-angle measurement, and atomic force microscopy. Two separate adherence assays and a material penetration assay assessed the performance of the new material against four strains of Candida species. Results showed a significant reduction (p < 0.01) of Candida albicans GDH 2346 adherence to silane-treated silicone compared with untreated controls. This reduction was still evident after the incorporation of saliva into the assay. Adherence inhibition also occurred with Candida tropicalis MMU and Candida krusei NCYC, although this was assay dependent. Reduced penetration of silane-treated silicone by Candida was evident when compared to untreated controls, plaster-processed silicone, and acrylic-processed silicone. To summarize, a novel silicone rubber material is described that inhibits both candidal adherence and material penetration. The clinical benefit and performance of this material remains to be determined.

Designing a prosthesis to simulate the elastic properties of skin.

The materials which are currently used to make maxillofacial prostheses are far from ideal and require considerable improvement with respect to their ability to mimic the properties of skin. To this aim, a novel three-layered maxillofacial prosthesis has been designed consisting of a silicone rubber base layer, an inner gel layer and an outer polymeric coating (to simulate the elastic properties of skin). The aim of the work in this study was to develop the inner silicone gel layer which displays similar properties to facial skin. Through the use of unique linear extensometry testing, in vivo measurements for the Area under the Curve (AUC), Hysteresis (viscoelastic behaviour), Fmax (maximum force), F30 and F60 (force after 30 and 60 seconds) were obtained from the facial skin of 15 volunteers. The results were used as a basis for developing silicone gel formulations for the inner layer, to closely resemble those of facial skin. Gels were made by the addition of both low and high molecular weight unreactive silicone fluids and were further tested for compression, water absorption and dehydration. Testing showed that a gel has been produced that closely simulates the elastic properties of skin when bonded to a base silicone rubber layer. Further testing will need to deduce whether these properties will be affected by the addition of the outer polymeric layer.

Surface modification of an experimental silicone rubber aimed at reducing initial candidal adhesion.

Silicone rubber, which is a widely used biomaterial, is often used to make soft liners for permanent denture. Colonization of denture soft lining materials by Candida albicans can result in clinical problems. The aim of this study was to chemically modify the surface of an experimental silicone rubber in order to produce a silicone that was less susceptible to candidal colonization. Surface modification was carried out with the use of argon-plasma bombardment followed by silane treatment, which caused the incorporation of either hydrophilic or hydrophobic functional groups onto the surface. Changes in water contact angles and chemical analysis of the materials with scanning ion mass spectroscopy confirmed surface changes. In vitro assays were carried out using C. albicans to measure levels of adherence to the surface-modified silicone after 1 h. C. albicans exhibited very low adherence to all silane-treated surfaces, whether hydrophobic or hydrophilic. This led to the conclusion that incorporated long-chain functional groups were inhibiting the adherence of the yeast, possibly by the formation of a barrier between the surface of the material and the yeast. In conclusion, silane surface treatment of an experimental silicone rubber has been successful in reducing candidal adherence.