Calibration Strategies for FT-IR and Other Isotope Ratio Infrared Spectrometer Instruments for Accurate δ13C and δ18O Measurements of CO2 in Air.

This paper describes calibration strategies in laboratory conditions that can be applied to ensure accurate measurements of the isotopic composition of the CO2 in ultradry air, expressed as δ13C and δ18O on the VPDB scale, with either FT-IR (in this case a Vertex 70 V (Bruker)) or an isotope ratio infrared spectrometer (IRIS) (in this case a Delta Ray (Thermo Fisher Scientific)). In the case of FT-IR a novel methodology using only two standards of CO2 in air with different mole fractions but identical isotopic composition was demonstrated to be highly accurate for measurements of δ13C and δ18O with standard uncertainties of 0.09‰ and 1.03‰, respectively, at a nominal CO2 mole fraction of 400 µmol mol-1 in air. In the case of the IRIS system, we demonstrate that the use of two standards of CO2 in air of known but differing δ13C and δ18O isotopic composition allows standard uncertainties of 0.18‰ and 0.48‰ to be achieved for δ13C and δ18O measurements, respectively. The calibration strategies were validated using a set of five traceable primary reference gas mixtures. These standards, produced with whole air or synthetic air covered the mole fraction range of (378-420) µmol mol-1 and were prepared and/or value assigned either by the National Institute of Standards and Technology (NIST) or the National Physical Laboratory (NPL). The standards were prepared using pure CO2 obtained from different sources, namely, combustion; Northern Continental and Southern Oceanic Air and a gas well source, with δ13C values ranging between -35‰ and -1‰. The isotopic composition of all standards was value assigned at the Max Planck Institute for Biogeochemistry Jena (MPI-Jena).

Methane standards made in whole and synthetic air compared by cavity ring down spectroscopy and gas chromatography with flame ionization detection for atmospheric monitoring applications.

There is evidence that the use of whole air versus synthetic air can bias measurement results when analyzing atmospheric samples for methane (CH4) and carbon dioxide (CO2). Gas chromatography with flame ionization detection (GC-FID) and wavelength scanned-cavity ring down spectroscopy (WS-CRDS) were used to compare CH4 standards produced with whole air or synthetic air as the matrix over the mole fraction range of 1600-2100 nmol mol(-1). GC-FID measurements were performed by including ratios to a stable control cylinder, obtaining a typical relative standard measurement uncertainty of 0.025%. CRDS measurements were performed using the same protocol and also with no interruption for a limited time period without use of a control cylinder, obtaining relative standard uncertainties of 0.031% and 0.015%, respectively. This measurement procedure was subsequently used for an international comparison, in which three pairs of whole air standards were compared with five pairs of synthetic air standards (two each from eight different laboratories). The variation from the reference value for the whole air standards was determined to be 2.07 nmol mol(-1) (average standard deviation) and that of synthetic air standards was 1.37 nmol mol(-1) (average standard deviation). All but one standard agreed with the reference value within the stated uncertainty. No significant difference in performance was observed between standards made from synthetic air or whole air, and the accuracy of both types of standards was limited only by the ability to measure trace CH4 levels in the matrix gases used to produce the standards.

Normal phase-liquid chromatography-tandem mass spectrometry with atmospheric pressure photoionization for the purity assessment of 17ß-estradiol.

A normal phase-liquid chromatography-hybrid tandem mass spectrometry (NP-LC-MS/MS) method utilizing atmospheric pressure photoionization (APPI) without dopant has been developed and implemented for the simultaneous determination of several estrogenic steroid hormones. The combination of both NP-LC and APPI-MS/MS tolerates the use of solvents that have the advantages of being self-doping for APPI and, at the same time, inhibit the in situ formation of estrogen dimers as frequently observed for conventional reversed phase (RP)-LC methods. The NP-LC-APPI-MS/MS method has been validated in-house, and its performance characteristics (linearity, repeatability, limits of detection, etc.) were assessed for use in the quantification of estrogens. Moreover, the method was used to characterize and determine the inherent related structure impurities in batches of ß-estradiol, required for the establishment of reference measurement systems for clinical chemistry and laboratory medicine, which served as candidate reference material for an organic purity assessment interlaboratory study (CCQM-K55.a) organized by the International Bureau of Weights and Measures (BIPM) Chemistry Department and carried out within the framework of the Organic Analysis Working Group (OAWG) of the Consultative Committee for Amount of Substance-Metrology in Chemistry (CCQM).

Accurate Fourier transform infrared (FT-IR) spectroscopy measurements of nitrogen dioxide (NO2) and nitric acid (HNO3) calibrated with synthetic spectra.

A novel method for determining the accuracy of laboratory-based measurements of nitrogen dioxide (NO2) and nitric acid (HNO3) mole fractions using Fourier transform infrared (FT-IR) spectroscopy 1 cm(-1) resolution instruments calibrated with synthetic spectra has been developed. The traceability of these measurement results is to the reference line strength data contained within the high-resolution transmission molecular absorption (HITRAN) database. Incorporating a proper estimate of the uncertainty of this data into the measurement results will ensure that the SI traceable values are encompassed within the uncertainty of the measurement results. The major contributors to the uncertainties of the results are, in descending order of importance, the uncertainty in the line strength values (HITRAN 2004), the uncertainty attributed to the generation of reference spectra (including knowledge of the optical path length of the FT-IR gas cell), and temperature measurements of the gas. The stability of the FT-IR instrument itself is only a minor contributor to the overall uncertainty of the measurements. FT-IR measurements of NO2 mole fractions at nominal values of 10 µmol mol(-1) calibrated with synthetic spectra lead to standard uncertainties of 0.34 µmol mol(-1) (3.4% relative). In contrast, calibration of the FT-IR instrument with SI traceable gas standards generated by a dynamic weighing system resulted in measurements results with standard uncertainties of 0.04 µmol mol(-1) (0.4% relative). When comparing the consistency of measurement results based on the synthetic calibration method against those obtained by calibrations with SI traceable gas standards, the existence of a potential bias of ~5% was observed, although this was within the stated uncertainties of the results. The FT-IR measurements of HNO3 mole fractions at nominal values of 200 nmol mol(-1) calibrated with synthetic spectra resulted in values with standard uncertainties of 23 nmol mol(-1) (11% relative) with the dominating uncertainty in this case arising from the stabilization of the mole fraction value within the FT-IR gas cell.

Mass balance method for the SI value assignment of the purity of organic compounds.

A mass balance method is described for determining the mass fraction of the main component of a high purity organic material. The resulting assigned value is established to be traceable to the SI and can be determined with a small associated measurement uncertainty. Pure organic materials with values and uncertainties determined in this way are necessary as primary calibrators of reference measurement systems in order to underpin the metrological traceability of routine measurement results. The method has been applied to materials in which the main components were respectively theophylline, digoxin, 17ß-estradiol, and aldrin. Its performance has been validated in international comparisons coordinated by the BIPM and is in principle applicable to a wide structural range of stable, nonvolatile organic compounds. It has been successfully applied to mass fraction assignments when the main component is present in the range of (950-1000) mg/g and can achieve associated standard uncertainties ranging from 0.5 mg/g (for high purity materials or those containing well-characterized, stable minor components) to 2 mg/g (materials with a significant number or variety of impurities). It is in principle equally applicable to materials with a smaller mass fraction content of the main component.

Highly accurate nitrogen dioxide (NO2) in nitrogen standards based on permeation.

The development and operation of a highly accurate primary gas facility for the dynamic production of mixtures of nitrogen dioxide (NO(2)) in nitrogen (N(2)) based on continuous weighing of a permeation tube and accurate impurity quantification and correction of the gas mixtures using Fourier transform infrared spectroscopy (FT-IR) is described. NO(2) gas mixtures in the range of 5 µmol mol(-1) to 15 µmol mol(-1) with a standard relative uncertainty of 0.4% can be produced with this facility. To achieve an uncertainty at this level, significant efforts were made to reduce, identify and quantify potential impurities present in the gas mixtures, such as nitric acid (HNO(3)). A complete uncertainty budget, based on the analysis of the performance of the facility, including the use of a FT-IR spectrometer and a nondispersive UV analyzer as analytical techniques, is presented in this work. The mixtures produced by this facility were validated and then selected to provide reference values for an international comparison of the Consultative Committee for Amount of Substance (CCQM), number CCQM-K74, (1) which was designed to evaluate the consistency of primary NO(2) gas standards from 17 National Metrology Institutes.

Simultaneous determination of various cardiac glycosides by liquid chromatography-hybrid mass spectrometry for the purity assessment of the therapeutic monitored drug digoxin.

A high performance liquid chromatography-hybrid tandem mass spectrometry (LC-MS(n)) method utilising electrospray ionisation has been developed and implemented for the simultaneous determination of several cardiac glycosides (CGs) as well as their corresponding aglycones formed by and extracted from herbaceous plants of the genus Digitalis. The method has been validated in-house and its performance characteristics (linearity, repeatability, limits of detection, etc.) were assessed for use in the quantification of CGs and their corresponding aglycones. LODs from 38 to 936pgg(-1) in solution, corresponding to mass fraction impurity levels from 0.0009 (or 0.00008%) to 0.019mgg(-1) (or 0.0019%) detectable in the pure materials have been realized. Moreover, the method was used to characterize and to determine the inherent CG impurities in batches of the therapeutic monitored drug digoxin which served as candidate reference material for an organic purity assessment inter-laboratory study (CCQM-P20.f) organised by the BIPM Chemistry Section and carried out within the framework of the Organic Analysis Working Group (OAWG) of the Consultative Committee for Amount of Substance - Metrology in Chemistry (CCQM). Digoxin was selected from materials required for the establishment of reference measurement systems for clinical chemistry and laboratory medicine.