Environmental decontamination of a hospital isolation room using high-intensity narrow-spectrum light.

The performance of a new decontamination technology, referred to as 'high-intensity narrow-spectrum light environmental decontamination system' (HINS-light EDS) was evaluated by a series of three studies carried out in a hospital isolation room used to treat burns patients. The ceiling-mounted HINS-light EDS emits high-intensity 405nm light which, although bactericidal, is harmless to patients and staff thereby permitting continuous environmental disinfection throughout the day. Performance efficacy was assessed by contact agar plate sampling and enumeration of staphylococcal bacteria on environmental surfaces within the room before, during and after HINS-light EDS treatment. When the room was unoccupied, use of HINS-light EDS resulted in ∼90% reduction of surface bacterial levels and when the room was occupied by an MRSA-infected burns patient, reductions between 56% and 86% were achieved, with the highest reduction (86%) measured following an extended period of HINS-light EDS operation. In an on/off intervention study, surface bacterial levels were reduced by 62% by HINS-light EDS treatment and returned to normal contamination levels two days after the system was switched off. These reductions of staphylococci, including Staphylococcus aureus and meticillin-resistant S. aureus, by HINS-light EDS treatment were greater than the reductions achieved by normal infection control and cleaning activities alone. The findings provide strong evidence that HINS-light EDS, used as a supplementary procedure, can make a significant contribution to bacterial decontamination in clinical environments.

The role of oxygen in the visible-light inactivation of Staphylococcus aureus.

Exposure to visible-light causes the photoinactivation of certain bacteria by a process that is believed to involve the photo-stimulation of endogenous intracellular porphyrins. Studies with some bacterial species have reported that this process is oxygen-dependent. This study examines the role of oxygen in the visible-light inactivation of Staphylococcus aureus. Suspensions of S. aureus were exposed to broadband visible-light under both oxygen depletion and oxygen enhancement conditions to determine whether these environmental modifications had any effect on the staphylococcal inactivation rate. Oxygen enhancement was achieved by flowing oxygen over the surface of the bacterial sample during light inactivation and results demonstrated an increased rate of staphylococcal inactivation, with approximately 3.5 times less specific dose being required for inactivation compared to that for a non-enhanced control. Oxygen depletion, achieved through the addition of oxygen scavengers to the S. aureus suspension, further demonstrated the essential role of oxygen in the light inactivation process, with significantly reduced staphylococcal inactivation being observed in the presence of oxygen scavengers. The results of the present study demonstrate that the presence of oxygen is important for the visible-light inactivation of S. aureus, thus providing supporting evidence that the nature of the mechanism occurring within the visible-light-exposed staphylococci is photodynamic inactivation through the photo-excitation of intracellular porphyrins.

Pulsed ultra-violet inactivation spectrum of Escherichia coli.

Inactivation of Escherichia coli is examined using ultra-violet (UV) radiation from a pulsed xenon flashlamp. The light from the discharge has a broadband emission spectrum extending from the UV to the infrared region with a rich UV content. The flashlamp provides high-energy UV output using a small number of short-duration pulses (30 micros). The flashlamp is used with a monochromator to investigate the wavelength sensitivity of E. coli to inactivation by the pulsed UV light. Using 8 nm wide pulses of UV radiation, the most efficient inactivation is found to occur at around 270 nm and no inactivation is observed above 300 nm. A pyroelectric detector allows the energy dose to be determined at each wavelength, and a peak value for E. coli population reduction of 0.43 log per mJ/cm(2) is measured at 270 nm. The results are compared with the published data available for continuous UV light sources.

Optical fiber sensor for electric field and electric charge using low-coherence, Fabry-Perot interferometry.

An optical fiber sensor for electric field and electric charge, based on the deflection of a small cantilever, has been developed. When the sensor head is placed in an electric field, induced charging produces deflection of the cantilever, which is measured using low-coherence, Fabry-Perot interferometry. The sensor has been used to measure the electric field in the vicinity of a Van de Graaff generator, in the range 135-650 V/cm. The measured deflections are in good agreement with the predictions of a simple model equating the electrostatic and mechanical forces acting on the cantilever.

Characterization and use of an optical fiber interferometer for measurement of the electric wind.

An optical fiber interferometer of the Mach-Zehnder type has proved to be a convenient and accurate method for measuring the electric wind in the active region of a corona discharge. The technique relies on the cooling effect of the wind on a small heated region of one arm of the interferometer, which has been remotely heated with an infrared CO(2) laser beam. Wind speeds of up to 5.5 m s(-1) have been measured near the generation region, and by the use of a mesh electrode, the wind has been detected on the axis up to 0.5 m away from the gap. A number of characterization experiments that show the interferometer to be a useful diagnostic tool in the quantitative analysis of the CO(2) laser beam have also been carried out, and good agreement between experimental results and theoretical calculations based on a simple heat-power balance equation for the fiber exists.

Versatile polarization interferometer.

A new form of polarizing interferometer has been assembled from six calcite-glass prisms and two halfwave plates. The interferometer has the large shear and long beam path capabilities needed for the examination of large objects and is capable of providing a stable interference pattern even when the two ends of the interferometer are supported independently. Lenses can be conveniently added to the system either to facilitate alignment or to extend its useful length.

Integration over cylindrical luminous volumes using a calibrated piston source.

A method is described for measuring the absolute light output from a gas or liquid in a cylindrical tube. The apparatus used is simple to build and use. The technique results in measurements of unusually high accuracy and sensitivity. The volume integration, often done with the aid of a mathematical model, is replaced by the physical measurement made by moving a calibrated luminous disk along the axis of the empty cylindrical tube.