Comparison of metal versus absorbable implants in tension-band wiring: a preliminary study.

The strength of tension-band wiring using bioabsorbable materials versus metal implants was assessed with a rabbit knee fusion model. Ten rabbit knees were osteotomized and rigidly fixed using a tension-band technique: five with metal implants (2 pins and 24-gauge wire) and five with absorbable implants (2-mm pins [Bionx, Blue Bell, Pa] and 1 Maxon [Davis and Geck, Danbury, Conn]). Biomechanical testing of the fixation strength was completed using a servohydraulic mechanical testing machine and a specifically designed four-point bending jig. The parameters assessed were maximal load, relative stiffness, displacement, and bending moment of the constructs. Results of the biomechanical testing showed no statistical difference between the constructs on any of the parameters assessed.

Mechanical comparison of two external fixator clamp designs.

OBJECTIVE: To compare two external fixation clamp designs for their ability to resist movement of a fixation pin in relation to the connecting rod. STUDY DESIGN: Two designs of external fixator clamps were attached to connecting rods mounted on a jig for mechanical testing. Fixator pins were placed perpendicular to the connecting rod. A mechanical testing machine was used to deflect each 3.2-mm pin at a distance that was 25 mm from the center of the clamp bolt. Both clamp designs were tightened to 4.4, 6.1, and 7.8 newton-meters (N x m) torque, and loads were applied in a position ramp through 4 mm and resisting loads were measured. Two clamp orientations were used during load application, such that the deflection of the pin tended to tighten the clamp bolt or tended to loosen the clamp bolt. The tests were videotaped to determine mode of failure. Comparisons of the load/displacement curves for the two external fixator clamp designs were made using nonlinear equational curve fitting methods. The resultant plateau and rise coefficients were compared using analysis of variance. RESULTS: Slippage of the pin in relation to the clamp occurred with the Kirschner-Ehmer clamp tightened to 4.4, 6.1, and 7.8 N x m, and slipping of the pin in relation to the clamp occurred with the experimental clamp design tightened to 4.4 and 6.1 N x m but not to 7.8 N m. At 7.8 N x m, the 3.2-mm pin deformed plastically with the experimental clamp design. Increasing the torque of the clamp bolt resulted in superior plateau coefficients for both clamp designs. At each level of tightness and in each clamp orientation to applied pin load, the experimental clamp design provided greater plateau coefficients than did the Kirschner-Ehmer clamp design. At 7.8 N x m of tightness, the Kirschner-Ehmer clamp and bolt bent, whereas only slight plastic deformation of the experimental clamp design occurred. CONCLUSIONS: The experimental external fixator clamp was more secure in resisting fixator pin movement at all levels of tightening compared with the Kirschner-Ehmer-type external fixator clamp. At 7.8 N x m of tightening, the new clamp design did not allow slippage of the pin within the clamp. CLINICAL SIGNIFICANCE: The experimental external fixator clamp should result in greater rigidity of fixator configurations, in addition to providing design features that allow addition of a clamp between two installed clamps, sleeved predrilling of pilot holes for all pins, measurement of pin depth, and placement of positive profile pins at all sites.

Type-II external fixation, using new clamps and positive-profile threaded pins, for treatment of fractures of the radius and tibia in dogs.

A new external fixation system for repair of fractures of the radius and tibia was developed that uses positive-profile threaded pins. This system allows for addition of a fixation clamp between 2 installed clamps, predrilling of pin holes through a drill sleeve, use of positive-profile threaded pins in all locations, and easier application of full pins. Type-II external fixators were applied, using this system, to fractures in 10 client-owned dogs, and outcome was evaluated. All fractures healed without complications. Duration of surgery, mean time until radiographic evidence of a bridging callus, and mean time until removal of the external fixator were shorter, and frequency of pin loosening were less than with other techniques. Pin loosening was uncommon. This system provides an important improvement in external skeletal fixation.