RESUMO
Correction for 'UV and VUV-induced fragmentation of tin-oxo cage ions' by Jarich Haitjema et al., Phys. Chem. Chem. Phys., 2021, 23, 20909-20918, https://doi.org/10.1039/D1CP03148A.
RESUMO
Extreme ultraviolet (EUV) lithography uses 13.5 nm light to reach the sub-20 nm resolution. However, the process of pattern formation induced by this high-energy light is not well-understood. In this work, we provide an inorganic EUV photoresist with fluorescence properties by introducing a carbazole derivative as a ligand, and we study its effect on the patterning process. Using the fluorescence properties, changes in the emission of the material after EUV exposure could be tracked by means of spectroscopy and microscopy. The resist sensitivity was substantially reduced by the incorporation of the carbazole benzoate ligands, which is attributed to hole trapping and steric hindrance. After EUV irradiation of the resist films, infrared, UV-visible absorption, and fluorescence spectroscopies showed that the carbazole units were still mostly intact, although their fluorescence intensity was lowered. Our work shows that fluorescent labeling can provide relevant mechanistic insights in the patterning process of resists, potentially with a molecular resolution.
RESUMO
Photoresist materials are being optimized for the recently introduced Extreme Ultraviolet (EUV) photolithographic technology. Organometallic compounds are potential candidates for replacing the ubiquitous polymer-based chemically amplified resists. Tin (Sn) has a particularly large absorption cross section for EUV light (13.5 nm, 92 eV), which could lead to a lower required EUV dose for achieving the desired solubility change (improved sensitivity). However, the fundamental interaction between organometallic materials and higher energy photons is poorly understood. In this work, we exposed n-butyltin-oxo cage dications (M2+) in the gas phase to photons in the energy range 4-35 eV to explore their fundamental photoreactivity. Photoproducts were detected using mass spectrometry. Homolytic cleavage of tin-carbon bonds was observed for all photon energies above the onset of electronic absorption at â¼5 eV (â¼250 nm), leading to photoproducts which have lost one or more of the attached butyl groups (Bu). Above 12 eV (<103 nm), dissociative photoionization occurred for the dication (M2+), competing with the neutral loss channels. The photoionization threshold is lowered by approximately 2 eV when one counterion (triflate, OTf- or tosylate, OTs-) is attached to the tin-oxo cage (MOTf+ and MOTs+). This threshold is expected to be even lower if each tin-oxo cage is attached to two counterions, as is the case in a solid film of tin-oxo cages. Addition of counterions also affected the fragmentation pathways; photoexcitation of (MX)+ (X = counterion, OTf or OTs) always led to formation of (MX-2Bu)+ rather than (MX-Bu)+. MOTs+ was much more reactive than MOTf+ in terms of reaction products per absorbed photon. A possible explanation for this is proposed, which involves the counterion reacting with the initially formed tin-based radical.
RESUMO
Colloidal quantum dots have found many applications and patterning them on micro- and nanoscale would open a new dimension of tunability for the creation of smaller scale (flexible) electronics or nanophotonic structures. Here we present a simple, general, one-step top-down patterning technique for colloidal quantum dots by means of direct optical or electron beam lithography. We find that both photons and electrons can induce a solubility switch of both PbS and CdSe quantum dot films. The solubility switch can be ascribed to cross-linking of the organic ligands, which we observe from exposure with deep-UV photons (5.5 eV) to extreme-UV photons (91.9 eV), and low-energy (3-70 eV) as well as highly energetic electrons (50 keV). The required doses for patterning are relatively low and feature sizes can be as small as tens of nanometers. The luminescence properties as well as carrier lifetimes remain similar after patterning.
