Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 2 de 2
Filtrar
Mais filtros










Base de dados
Intervalo de ano de publicação
1.
Materials (Basel) ; 17(11)2024 May 24.
Artigo em Inglês | MEDLINE | ID: mdl-38893808

RESUMO

Due to the volume expansion effect during charge and discharge processes, the application of transition metal oxide anode materials in lithium-ion batteries is limited. Composite materials and carbon coating are often considered feasible improvement methods. In this study, three types of TiO2@Fe3O4@C microspheres with a core-double-shell structure, namely TFCS (TiO2@Fe3O4@C with 0.0119 g PVP), TFCM (TiO2@Fe3O4@C with 0.0238 g PVP), and TFCL (TiO2@Fe3O4@C with 0.0476 g PVP), were prepared using PVP (polyvinylpyrrolidone) as the carbon source through homogeneous precipitation and high-temperature carbonization methods. After 500 cycles at a current density of 2 C, the specific capacities of these three microspheres are all higher than that of TiO2@Fe2O3 with significantly improved cycling stability. Among them, TFCM exhibits the highest specific capacity of 328.3 mAh·g-1, which was attributed to the amorphous carbon layer effectively mitigating the capacity decay caused by the volume expansion of iron oxide during charge and discharge processes. Additionally, the carbon coating layer enhances the electrical conductivity of the TiO2@Fe3O4@C materials, thereby improving their rate performance. Within the range of 100 to 1600 mA·g-1, the capacity retention rates for TiO2@Fe2O3, TFCS, TFCM, and TFCL are 27.2%, 35.2%, 35.9%, and 36.9%, respectively. This study provides insights into the development of new lithium-ion battery anode materials based on Ti and Fe oxides with the abundance and environmental friendliness of iron, titanium, and carbon resources in TiO2@Fe3O4@C microsphere anode materials, making this strategy potentially applicable.

2.
Materials (Basel) ; 17(7)2024 Mar 26.
Artigo em Inglês | MEDLINE | ID: mdl-38612025

RESUMO

This study combined inorganic α-hemihydrate gypsum (α-HHG) with organic polyacrylamide (PAM) hydrogel to create a novel α-HHG/PAM composite material. Through this facile composite strategy, this fabricated material exhibited a significantly longer initial setting time and higher mechanical strength compared to α-HHG. The effects of the addition amount and the concentration of PAM precursor solution on the flowability of the α-HHG/PAM composite material slurry, initial setting time, and mechanical properties of the hardened specimens were investigated. The structural characteristics of the composite material were examined using XRD, FE-SEM, and TGA. The results showed that the initial setting time of the α-HHG/PAM composite material was 25.7 min, which is an extension of 127.43% compared to that of α-HHG. The flexural strength and compressive strength of the oven-dried specimens were 23.4 MPa and 58.6 MPa, respectively, representing increases of 34.73% and 84.86% over values for α-HHG. The XRD, FE-SEM, and TGA results all indicated that the hydration of α-HHG in the composite material was incomplete. The incompleteness is caused by the competition between the hydration process of inorganic α-HHG and the gelation process of the acrylamide molecules for water, which hinders some α-HHG from entirely reacting with water. The enhanced mechanical strength of the α-HHG/PAM composite material results from the tight interweaving and integrating of organic and inorganic networks. This study provides a concise and efficient approach to the modification research of hemihydrate gypsum.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA
...