Investigation on the Deformation and Surface Quality of a Bearing Outer Ring during Grinding Processing.

Thin-walled bearings are widely used owing to the advantages of their light structure, high hardness, and strong load-carrying capacity. However, thin-walled bearings are often prone to deformation during the machining process, which can seriously affect the performance of the bearings. In addition, the machining deformation and quality of bearings are difficult to balance. To address the above issues, this paper investigates the effects of the machining parameters on the machining deformation, surface quality, and machining efficiency of a thin-walled bearing during the roughing stage. The dynamic balance between deformation inhibition and high quality in rough grinding was studied, and the optimal parameters for thin-walled bearing outer ring grinding were obtained. The deformation mechanism of thin-walled bearings caused by grinding was revealed through simulation and experimental analysis. The results show that the machining deformation and quality reach a balance when the workpiece speed is 55 r/min, the grinding wheel rotational speed is 2000 r/min, and the feed rate is 0.1 mm/min. Deformation increases with the increase in workpiece speed and grinding wheel speed. At the same time, the surface roughness increases with the increase in the workpiece speed, but the increase in the wheel speed will improve the surface roughness. As the workpiece speed increases, the surface topography shows a more pronounced stockpile of material, which is ameliorated by an increase in grinding wheel speed. As the rotational speed of the workpiece increases, the number of abrasive grains involved in the process per unit of time decreases, and the surface removal of the workpiece is less effective, while the increase in the rotational speed of the grinding wheel has the opposite effect. The grinding deformation of thin-walled bearings is mainly induced by machining heat and stress. As the rotational speed increases, the heat flux in the grinding zone increases. More heat flux flows into the surface of the workpiece, causing an increase in thermal stresses on the inner surface of the bearing collar, leading to greater deformation. The temperature in the grinding area can be reduced during machining, realizing a reduction in deformation. The research content contributes to the balance between high quality and low distortion in machining processes.

An Automatic 3-D Ultrasound and Photoacoustic Combined Imaging System for Human Inflammatory Arthritis.

Aiming at a point-of-care device for rheumatology clinics, we developed an automatic 3-D imaging system combining the emerging photoacoustic (PA) imaging with conventional Doppler ultrasound (US) for detecting human inflammatory arthritis. This system is based on a commercial-grade GE HealthCare (GEHC, Chicago, IL, USA) Vivid E95 US machine and a Universal Robot UR3 robotic arm. This system automatically locates the patient's finger joints from a photograph taken by an overhead camera powered by an automatic hand joint identification method, followed by the robotic arm moving the imaging probe to the targeted joint to scan and obtain 3-D PA and Doppler US images. The GEHC US machine was modified to enable high-speed, high-resolution PA imaging while maintaining the features available on the system. The commercial-grade image quality and the high sensitivity in detecting inflammation in peripheral joints via PA technology hold great potential to significantly benefit clinical care of inflammatory arthritis in a novel way.

Defect and strain engineered MoS2/graphene catalyst for an enhanced hydrogen evolution reaction.

Molybdenum disulfide (MoS2) has been demonstrated as a promising non-precious metal electrocatalyst for the hydrogen evolution reaction (HER). However the efficiency of the HER falls short of expectations due to the large inert basal plane and poor electrical conductivity. In order to activate the MoS2 basal plane and enhance the hydrogen evolution reaction (HER) activity, two strategies on the hybrid MoS2/graphene, including intrinsic defects and simultaneous strain engineering, have been systematically investigated based on density functional theory calculations. We firstly investigated the HER activity of a MoS2/graphene hybrid material with seven types of point defect sites, V S, VS2, V Mo, V MoS3, V MoS6, MoS2 and S2Mo. Using the hydrogen adsorption free energy (ΔG H) as the descriptor, results demonstrate that four of these seven defects (V S, V S2, MoS2, V MoS3) act as a catalytic active site for the HER and exhibited superior electrocatalytic activity. More importantly, we found that ΔG H can be further tuned to an ideal value (0 eV) with proper tensile strain, which effectively optimizes and boosts the HER activity, especially for the V S, V S2, V MoS3 defects and MoS2 antisite defects. Our results demonstrated that a proper combination of tensile strain and defect structure is an effective approach to achieve more catalytic active sites and further tune and boost the intrinsic activity of the active sites for HER performance. Furthermore, the emendatory d-band center of metal proves to be an excellent descriptor for determining H adsorption strength on defective MoS2/graphene hybrid material under different strain conditions. In addition, the low kinetic barrier of H2 evolution indicated that the defective MoS2/graphene system exhibited favorable kinetic activity in both the Volmer-Heyrovsky and the Volmer-Tafel mechanism. These results may pave a new way to design novel ultrahigh-performance MoS2-based HER catalysts.

The Synergistic Antibacterial Mechanism of Gentamicin-Loaded CaCO 3 Nanoparticles.

In the present study, we used CaCO3 nanoparticles (CCNPs) as carriers to assess the physicochemical characteristics and antibacterial effect of gentamicin sulfate (GS)-loaded CCNPs (CGPs). The results indicated that CCNPs had relatively regular chain-like structure, and the size of the crystallites was around 62.5 nm. FT-IR analysis indicated that the GS could effectively load onto CCNPs. Meanwhile, the dosage of CCNPs would affect the drug loading and entrapment efficiency of GS. CCNPs could prolong the release of GS, and the complete release of GS from CCNPs was extended up to 24 h. Additionally, CCNPs could obviously increase the antibacterial effect of GS. The zeta potential analysis and microscopic investigations indicated that the adsorbed CCNPs could increase the damage level of bacterial cell wall and enhance the permeability of cell membranes, leading to increased bacterial death.