The Highly Sensitive Refractive Index Sensing of Seawater Based on a Large Lateral Offset Mach-Zehnder Interferometer.

A novel fiber sensor for the refractive index sensing of seawater based on a Mach-Zehnder interferometer has been demonstrated. The sensor consisted of a single-mode fiber (SMF)-no-core fiber (NCF)-single-mode fiber structure (shortened to an SNS structure) with a large lateral offset spliced between the two sections of a multimode fiber (MMF). Optimization studies of the multimode fiber length, offset SNS length, and vertical axial offset distance were performed to improve the coupling efficiency of interference light and achieve the best extinction ratio. In the experiment, a large lateral offset sensor was prepared to detect the refractive index of various ratios of saltwater, which were used to simulate seawater environments. The sensor's sensitivity was up to -13,703.63 nm/RIU and -13,160 nm/RIU in the refractive index range of 1.3370 to 1.3410 based on the shift of the interference spectrum. Moreover, the sensor showed a good linear response and high stability, with an RSD of only 0.0089% for the trough of the interference in air over 1 h.

Nd:YVO4/YVO4 cascaded Raman laser pumped dual-wavelength signal wave MgO:PPLN-OPO with wide range adjustable wavelength interval.

This article presents a dual-wavelength signal wave output system capable of generating a broad range of adjustable wavelength intervals. The setup involved the creation of a dual-wavelength cascaded Raman laser featuring composite cavities operating at 1176 nm and 1313 nm. Experimental investigations were carried out on an external cavity MgO:PPLN-OPO driven by the cascaded Raman laser. By setting the crystal polarization period to 27.6-34.4 µm and the temperature to 50-130°C, adjustable tunable output of dual-wavelength signal wave at 1176 nm-MgO:PPLN-OPO (1550-2294 nm) and 1313 nm-MgO:PPLN-OPO (1768-2189 nm) was achieved with a wavelength interval of 0-218 nm. Under the conditions of a period of 34.4 µm, temperature of 90°C, and an incident Raman power of 2.6 W, the highest conversion efficiency of Raman to dual-wavelength signal wave (2212, 2182 nm) was 34.2%. Furthermore, the maximum output power of dual-wavelength signal wave was recorded at 1.02 W with an incident Raman power of 3.33 W.

Tunable metasurfaces for implementing terahertz controllable NOT logic gate functions.

Compared with traditional electrical logic gates, optical or terahertz (THz) computing logic gates have faster computing speeds and lower power consumption, and can better meet the huge data computing needs. However, there are limitations inherent in existing optical logic gates, such as single input/output channels and susceptibility to interference. Here, we proposed a new approach utilizing polarization-sensitive graphene-vanadium dioxide metasurface THz logic gates. Benefitting from two actively tunable materials, the proposed controlled-NOT logic gate(CNOT LG) enables versatile functionality through a dual-parameter control system. This system allows for the realization of multiple output states under diverse polarized illuminating conditions, aligning with the expected input-output logic relationship of the CNOT LG. Furthermore, to demonstrate the robustness of the designed THz CNOT LG metasurface, we designed an imaging array harnessing the dynamic control capabilities of tunable meta-atoms, facilitating clear near-field imaging. This research is promising for advancing CNOT LG applications in the THz spectrum. It has potential applications in telecommunications, sensing, and imaging.

High-sensitivity THz-ATR imaging of cerebral ischemia in a rat model.

The fast label-free detection of the extent and degree of cerebral ischemia has been the difficulty and hotspot for precise and accurate neurosurgery. We experimentally demonstrated that the fresh cerebral tissues at different ischemic stages within 24 hours can be well distinguished from the normal tissues using terahertz (THz) attenuated total reflection (ATR) imaging system. It was indicated that the total reflectivity of THz wave for ischemic cerebral tissues was lower than that for normal tissues. Especially, compared to the images stained with 2,3,5-triphenyl tetrazolium chloride (TTC), the ischemic tissues can be detected using THz wave with high sensitivity as early as the ischemic time of 2.5 hours, where THz images showed the ischemic areas became larger and diffused as the ischemic time increasing. Furthermore, the THz spectroscopy of cerebral ischemic tissues at different ischemic times was obtained in the range of 0.5-2.0 THz. The absorption coefficient of ischemic tissue increased with the increase of ischemic time, whereas the refractive index decreased with prolonging the ischemic time. Additionally, it was found from hematoxylin and eosin (H&E) staining microscopic images that, with the ischemic time increasing, the cell size and cell density of the ischemic tissues decreased, whereas the intercellular substance of the ischemic tissues increased. The result showed that THz recognition mechanism of the ischemia is mainly based on the increase of intercellular substance, especially water content, which has a stronger impact on absorption of THz wave than that of cell density. Thus, THz imaging has great potential for recognition of cerebral ischemia and it may become a new method for intraoperative real-time guidance, recognition in situ, and precise excision.

Interdisciplinary analysis and optimization of digital photonic devices for meta-photonics.

With the continuous integration and development of AI and natural sciences, we have been diligently exploring a computational analysis framework for digital photonic devices. Here, We have overcome the challenge of limited datasets through the use of Generative Adversarial Network networks and transfer learning, providing AI feedback that aligns with human knowledge systems. Furthermore, we have introduced knowledge from disciplines such as image denoising, multi-agent modeling of Physarum polycephalum, percolation theory, wave function collapse algorithms, and others to analyze this new design system. It represents an accomplishment unattainable within the framework of classical photonics theory and significantly improves the performance of the designed devices. Notably, we present theoretical analyses for the drastic changes in device performance and the enhancement of device robustness, which have not been reported in previous research. The proposed concept of meta-photonics transcends the conventional boundaries of disciplinary silos, demonstrating the transformative potential of interdisciplinary fusion.

All-Silicon Polarization-Insensitive Metamaterial Absorber in the Terahertz Range.

All-silicon terahertz absorbers have attracted considerable interest. We present a design and numerical study of an all-silicon polarization-insensitive terahertz metamaterial absorber. The meta-atoms of the metamaterial absorber are square silicon rings which can be viewed as gratings. By properly optimizing the structure of the meta-atom, we achieve a broadband absorptivity that is above 90% ranging from 0.77 THz to 2.53 THz, with a relative bandwidth of 106.7%. Impedance matching reduces the reflection of the terahertz waves and the (0, ±1)-order diffraction induce the strong absorption. The absorption of this absorber is insensitive to the polarization of the terahertz wave and has a large incident angle tolerance of up to 60 degrees. The all-silicon metamaterial absorber proposed here provides an effective way to obtain broadband absorption in the terahertz regime. Metamaterial absorbers have outstanding applications in terahertz communication and imaging.

High responsivity photodetector based on MEH-PPV/CsPbBr3heterojunction.

Perovskite quantum dots (QDs) and organic materials have great research potential in the field of optoelectronic devices. In this paper, MEH-PPV/CsPbBr3heterojunction photodetectors (PDs) are prepared by spin coating method based on the good photoelectric properties of CsPbBr3perovskite QDs and MEH-PPV. The MEH-PPV/CsPbBr3heterojunction improves the energy level arrangement, and CsPbBr3QDs can passivate the surface defects of MEH-PPV films to achieve effective charge separation and transfer, thus inhibiting the dark current and improving the photoelectric performance of the device. Under 532 nm laser irradiation, the responsivity (R) of MEH-PPV/CsPbBr3heterojunction PD is 11.98 A W-1, the specific detectivity (D*) is 6.98 × 1011Jones, and the response time is 15/16 ms. This work provides experience for the study of perovskite QDs and organic materials heterojunction optoelectronic devices.

Wavelength division multiplexing based on the coupling effect of helical edge states in two-dimensional dielectric photonic crystals.

Photonic topological insulators with topologically protected edge states featuring one-way, robustness and backscattering-immunity possess extraordinary abilities to steer and manipulate light. In this work, we construct a topological heterostructure (TH) consisting of a domain of nontrivial pseudospin-type topological photonic crystals (PCs) sandwiched between two domains of trivial PCs based on two-dimensional all-dielectric core-shell PCs in triangle lattice. We consider three THs with different number of layers in the middle nontrivial domain (i.e., one-layer, two-layer, three-layer) and demonstrate that the projected band diagrams of the three THs host interesting topological waveguide states (TWSs) with properties of one-way, large-area, broad-bandwidth and robustness due to coupling effect of the helical edge states associated with the two domain-wall interfaces. Moreover, taking advantage of the tunable bandgap between the TWSs by the layer number of the middle domain due to the coupling effect, a topological Y-splitter with functionality of wavelength division multiplexing is explicitly demonstrated exploiting the unique feature of the dispersion curves of TWSs in the three THs. Our work not only offers a new method to realize pseudospin-polarized large-area TWSs with tunable mode-width, but also could provide new opportunities for practical applications in on-chip multifunctional (i.e., wavelength division multiplexing) photonic devices with topological protection and information processing with pseudospin-dependent transport.

High performance CsBi3I10/PCBM bulk heterojunction perovskite photodetector.

Lead halide perovskites (LHPs) have been extensively studied due to their remarkable optoelectronic performance. However, the toxicity of a lead ion to humans and its instability under ambient conditions render lead-based halide perovskite an unsuitable material for commercialization. Meanwhile, lead-free halide perovskite (LFHP) devices generally exhibit poor performance. Therefore, enhancing photoelectric conversion capacity is the most important issue that needs to be addressed. Here, we propose a photodetector (PD) fabricated using C s B i 3 I 10/p h e n y l-C 61-butyric acid methyl ester (PCBM) bulk heterojunction as the active layer. The PD illuminated under 532 nm can reach a high responsivity (1.54 A/W) at -2V bias, while at 2 V bias, the PD reaches a higher responsivity (224.40 A/W). All of those results suggest that C s B i 3 I 10/P C B M bulk heterojunctions hold enormous potential in substituting for LHPs in optoelectronic devices.

MAPbI3perovskite photodetectors for high-performance optical wireless communication.

High-sensitivity and fast-response photodetectors (PDs) are vital part of optical wireless communication (OWC) system. In this work, we develop an organic-inorganic hybrid perovskite material (MAPbI3) based p-i-n structured PD. By optimizing the precursor solution concertation, the PD showed a high responsivity of 0.98 A W-1, a fast response timetrise/tfallof 12/12.5 µs, a specific detectivity of 2.62 × 1013Jones, and the f-3dBof 24 kHz under the 532 nm laser and -0.2 V bias voltage. Furthermore, we designed an OWC system based on the prepared PD. With the baud rate of 19200 bps, the system exhibits a bit error rate less than 10-6, and it can realize 9.63 m long-distance communication and quick transmission applications such as strings, texts, photos, and audios. Our work demonstrates the great application potential of perovskite PDs in the field of optical communication.

Investigation of unidirectional coupling of dipole emitters in valley photonic heterostructure waveguides.

Photonic heterostructure has recently become a promising platform to study topological photonics with the introduction of mode width degree of freedom (DOF). However, there is still a lack of comprehensive analysis on the coupling of dipole emitters in photonic heterostructures, which constrains the development of on-chip quantum optics based on chiral dipole sources. We systematically analyze the unidirectional coupling mechanism between dipole emitters and valley photonic heterostructure waveguides (VPHWs). With the eigenmode calculations and full-wave simulations, the Stokes parameters are obtained to compare the coupling performance of two types of valley-interface VPHWs. Simulation results show that compared to the zigzag interface with inversion symmetry, the strategy of bearded interface with glide symmetry is easier to realize high-efficiency coupling. By adjusting the position and chirality of dipole emitters in VPHWs, the transmission of light reverses with guided modes coupled to different directions. Furthermore, a topological beam modulator is realized based on VPHWs, which maintains the robustness to large-area potential barriers and sharp corners. Our work supplies a powerful guide for chiral light-matter interaction, which is expected to be applied to increasingly compact and efficient on-chip optical platforms in the future.

All-Dielectric Integrated Meta-Antenna Operating in 6G Terahertz Communication Window.

Efficient transceivers and antennas at terahertz frequencies are leading the development of 6G terahertz communication systems. The antenna design for high-resolution terahertz spatial sensing and communication remains challenging, while emergent metallic metasurface antennas can address this issue but often suffer from low efficiency and complex manufacturing. Here, an all-dielectric integrated meta-antenna operating in 6G terahertz communication window for high-efficiency beam focusing in the sub-wavelength scale is reported. With the antenna surface functionalized by metagrating arrays with asymmetric scattering patterns, the design and optimization methods are demonstrated with a physical size constraint. The highest manipulation and diffraction efficiencies achieve 84.1% and 48.1%. The commercially accessible fabrication method with low cost and easy to implement has been demonstrated for the meta-antenna by photocuring 3D printing. A filamentous focal spot is measured as 0.86λ with a long depth of focus of 25.3λ. Its application for integrated imaging and communication has been demonstrated. The proposed technical roadmap provides a general pathway for creating high-efficiency integrated meta-antennas with great potential in high-resolution 6G terahertz spatial sensing and communication applications.

An all-silicon design of a high-efficiency broadband transmissive terahertz polarization convertor.

Polarization, a fundamental behavior of electromagnetic waves, holds immense potential across diverse domains such as environmental monitoring, biomedicine, and ocean exploration. However, achieving efficient modulation of terahertz waves with wide operational bandwidth poses significant challenges. Here, we introduce an all-silicon polarization converter designed specifically to operate in the terahertz range of the electromagnetic spectrum. Simulation results demonstrate that the average conversion efficiency of cross-linear waves exceeds 80% across a wide frequency range spanning from 1.00 to 2.32 THz, with the highest conversion efficiency peaking at an impressive 99.97%. Additionally, our proposed structure facilitates linear-to-circular polarization conversion with an ellipticity of 1 at 0.85 THz. Furthermore, by rotating the cross-shaped microstructure, active control over arbitrary polarization states can be achieved. To summarize, the proposed structure offers remarkable flexibility and ease of integration, providing a reliable and practical solution for achieving broadband and efficient polarization conversion of terahertz waves.

1.2†W single-frequency Tm3+/Ho3+ co-doped fiber oscillator at 2050†nm.

In this Letter, a watt-level single-frequency fiber oscillator at 2050 nm was demonstrated for the first time, to the best of our knowlegde, in a linear laser cavity with a piece of an un-pumped Tm3+/Ho3+ co-doped fiber serving as a saturable absorber. With delicate optimization of mode filtering effect of the dynamic gratings formed in the saturable absorber, a maximum single-frequency laser output power of 1.2 W was achieved under a total bidirectional pump power of 5.8 W at 1570 nm, and the corresponding optical efficiency is 20.7%. This is, to the best of our knowledge, the highest power of a single-frequency fiber oscillator at the wavelength above 2 µm.

Widely tunable single-frequency Er-doped ZBLAN fiber laser with emission from 3.37 to 3.72†µm.

We demonstrate a widely tunable single-frequency Er-doped ZBLAN fiber laser operating on a 4F9/2→4I9/2 transition band. An uncoated germanium (Ge) plate serves as a narrow-bandwidth etalon and is inserted in the cavity to achieve a single longitudinal mode selection. Wavelength tuning from 3373.8 nm to 3718.5 nm was demonstrated by using a blazed diffraction grating at 3.5 µm. At the emission peak of 3465.6 nm, the laser yields over 100 mW single-frequency output power, with a 3 dB linewidth <6.9 MHz, and a slope efficiency (with respect to the incident 1990 nm pump power) of 20.3%. Such a tunable mid-infrared single-frequency fiber laser may serve as a versatile laser source in spectroscopy and sensing applications.

Efficient continuous-wave Nd:YVO4/KGW intracavity Raman laser.

We demonstrate an efficient Nd:YVO4/KGW intracavity Raman laser in continuous-wave (CW) scheme. With a V-shaped fundamental laser cavity and a short Stokes cavity in it, the oscillating beam sizes are designed to alleviate the thermal effect and to enhance the Raman gain for efficient CW operation. The output power of CW Stokes wave at 1177 nm reached 9.33 W under an incident laser diode pump power of 36.65 W, with corresponding optical efficiency being 25.5%. To the best of our knowledge, these are the highest Stokes output power and conversion efficiency of CW intracavity Raman lasers.

Narrow linewidth and wideband tunable continuous-wave terahertz generator based on difference frequency generation with DAST crystal.

A narrow linewidth and wideband tunable continuous-wave terahertz generator with DAST crystal has been demonstrated in this paper. Two narrow-linewidth CW fiber lasers were used as the pump sources for difference frequency generation. The terahertz wave can be continuously tunable in the range of 1.1-3 THz. The maximum output power of 2.79nW was obtained at 2.568 THz. The linewidth of the output THz wave was estimated to be 56.5 MHz by fitting transmission spectrum of CO gas at 450 Pa pressure around 80.52 cm-1 with the Vogit gas model. Furthermore, the output spectra at room temperature and pressure was in good agreement with the air absorption lines in Hitran database. Moreover, the narrower absorption characteristic spectrum of 2-Deoxy-D-Glucose sample has been obtained through the spectrum measurements. Therefore, it could promote the practical prospect of tunable CW-THz source, which will have good potential in THz high-precision spectroscopic detection and multispectral imaging.

Rapid and noninvasive cell assay by microfluidic-integrated intracavity evanescent field absorption in a fiber ring laser.

BACKGROUND: Highly sensitive and rapid detection of cell concentration and interfacial molecular events is of great value for biological, biomedical, and chemical research. Most traditional biosensors require large sample volumes and complicated functional modifications of the surface. It is of great significance to develop label-free biosensor platforms with minimal sample consumption for studying cell concentration changes and interfacial molecular events without labor-intensive procedures. RESULTS: Here, a fiber-optic biosensor based on intracavity evanescent field absorption sensing is designed for sensitive and label-free cell assays for the first time. The interaction between the cells and the evanescent field is enhanced by introducing microfluidic-integrated intracavity absorption in a fiber ring laser. This strategy extends the range of targeted analytes to include quantification of a large number of targets on a surface and improves the detection sensitivity of the fiber-optic biosensor. The level of sensing resolution could be improved from 10-4 RIU to 10-7 RIU using this strategy. The stem cells were studied over a wide concentration range (from 500 to 1.2 × 105 cells/ml) and were measured sequentially. By measuring the output power of the intracavity absorption sensing system, the cell concentration can be directly determined in a label-free manner. The results show that dozens of stem cells can be sensitively detected with a sample consumption of 72 µL. The response was fast (15 s) with a low temperature cross-sensitivity of 0.031 cells·ml-1/°C. SIGNIFICANCE: The proposed method suggests its capacity for true label-free and noninvasive cell assays with a low limit of detection and small sample consumption. This has the potential to be used as a universal tool for quantitative and qualitative characterization of various cells and other biochemical analytes.

Pump quantum efficiency optimization of 3.5 µm Er-doped ZBLAN fiber laser for high-power operation.

976 nm + 1976 nm dual-wavelength pumped Er-doped ZBLAN fiber lasers are generally accepted as the preferred solution for achieving 3.5 µm lasing. However, the 2 µm band excited state absorption from the upper lasing level (4F9/2 → 4F7/2) depletes the Er ions population inversion, reducing the pump quantum efficiency and limiting the power scaling. In this work, we demonstrate that the pump quantum efficiency can be effectively improved by using a long-wavelength pump with lower excited state absorption rate. A 3.5 µm Er-doped ZBLAN fiber laser was built and its performances at different pump wavelengths were experimentally investigated in detail. A maximum output power at 3.46 µm of ~ 7.2 W with slope efficiency (with respect to absorbed 1990 nm pump power) of 41.2% was obtained with an optimized pump wavelength of 1990 nm, and the pump quantum efficiency was increased to 0.957 compared with the 0.819 for the conventional 1976 nm pumping scheme. Further power scaling was only limited by the available 1990 nm pump power. A numerical simulation was implemented to evaluate the cross section of excited state absorption via a theoretical fitting of experimental results. The potential of further power scaling was also discussed, based on the developed model.

Terahertz narrowband filter metasurfaces based on bound states in the continuum.

The electromagnetically induced transparency (EIT) effect realized by metasurfaces have potential for narrowband filtering due to their narrow bandwidth. In optics, bound states in the continuum (BIC) can produce strong localized resonances, which means that light can be trapped and stored for long periods of time to produce very high Q-factors. This has potential applications in designing highly efficient sensors and narrow bandpass filters. Here, we present two metal-flexible dielectric metasurfaces consisting of copper structures and polyimide substrates. Quasi BICs are obtained by breaking C2 symmetry of the metal structures. Resonance-captured quasi-BICs with ultra-high q-factor resonances satisfy the dark modes required to realize the EIT and couple to the bright modes in the structure to achieve narrowband filtering. The peak transmission rates are around 0.9 at 0.29 THz-0.32 THz and 0.23 THz-0.27 THz, respectively. Our results have practical implications for the realization of low-frequency terahertz communications.