Elastic properties of thin poly(vinyl alcohol)-cellulose nanocrystal membranes.

In spite of extensive studies on the preparation and characterization of nanocomposite materials, the correlation of their properties at the nanoscale with those in bulk is a relatively unexplored area. This is of great importance, especially for materials with potential biomedical applications, where surface properties are as important in determining their applicability as bulk characteristics. In this study, the nanomechanical characteristics of thin poly(vinyl alcohol) (PVOH)-poly(acrylic acid) (PAA)-cellulose nanocrystal (CNC) membranes were studied using the nanoindentation module in an atomic force microscope (AFM) and the properties were compared with the macro-scale properties obtained by tensile tests. In general, the elastic properties measured by nanoindentation followed the same trend as macro-scale tensile tests except for the PVOH 85-PAA 0-CNC 15 sample. In comparison to the macro-scale elastic properties, the measured elastic moduli with AFM were higher. Macro-scale tensile test results indicated that, in the presence of PAA, incorporation of CNCs up to 20 wt% improved the elastic modulus of PVOH, but when no PAA was added, increasing the CNC content above 10 wt% resulted in their agglomeration and degradation in mechanical properties of PVOH. The discrepancy between macro-scale tensile tests and nanoindentation in the PVOH 85-PAA 0-CNC 15 sample was correlated to the high degree of inhomogeneity of CNC dispersion in the matrix. It was found that the composites reinforced with cellulose nanocrystals had smaller indentation imprints and the pile-up effect increased with the increase of cellulose nanocrystal content.

In situ observation of size-scale effects on the mechanical properties of ZnO nanowires.

In this investigation, the size-scale in mechanical properties of individual [0001] ZnO nanowires and the correlation with atomic-scale arrangements were explored via in situ high-resolution transmission electron microscopy (TEM) equipped with atomic force microscopy (AFM) and nanoindentation (NI) systems. The Young's modulus was determined to be size-scale-dependent for nanowires with diameter, d, in the range of 40 nm ≤ d ≤ 110 nm, and reached the maximum of ∼ 249 GPa for d = 40 nm. However, this phenomenon was not observed for nanowires in the range of 200 nm ≤ d ≤ 400 nm, where an average constant Young's modulus of ∼ 147.3 GPa was detected, close to the modulus value of bulk ZnO. A size-scale dependence in the failure of nanowires was also observed. The thick ZnO nanowires (d ≥ 200 nm) were brittle, while the thin nanowires (d ≤ 110 nm) were highly flexible. The diameter effect and enhanced Young's modulus observed in thin ZnO nanowires are due to the combined effects of surface relaxation and long-range interactions present in ionic crystals, which leads to much stiffer surfaces than bulk wires. The brittle failure in thicker ZnO wires was initiated from the outermost layer, where the maximum tensile stress operates and propagates along the (0001) planes. After a number of loading and unloading cycles, the highly compressed region of the thinner nanowires was transformed from a crystalline to an amorphous phase, and the region near the neutral zone was converted into a mixture of disordered atomic planes and bent lattice fringes as revealed by high-resolution images.

Revealing the 3D internal structure of natural polymer microcomposites using X-ray ultra microtomography.

Properties of composite materials are directly affected by the spatial arrangement of reinforcement and matrix. In this research, partially hydrolysed cellulose microcrystals were used to fabricate polycaprolactone microcomposites. The spatial distribution of cellulose microcrystals was characterized by a newly developed technique of X-ray ultra microscopy and microtomography. The phase and absorption contrast imaging of X-ray ultra microscopy revealed two-dimensional and three-dimensional information on CMC distribution in polymer matrices. The highest contrast and flux (signal-to-noise ratio) were obtained using vanadium foil targets with the accelerating voltage of 30 keV and beam current of >200 nA. The spatial distribution of cellulose microcrystals was correlated to the mechanical properties of the microcomposites. It was observed that heterogeneous distribution and clustering of cellulose microcrystals resulted in degradation of tensile strength and elastic modulus of composites. The utilization of X-ray ultra microscopy can open up new opportunities for composite researchers to explore the internal structure of microcomposites. X-ray ultra microscopy sample preparation is relatively simple in comparison to transmission electron microscopy and the spatial information is gathered at much larger scale.