Microstructural evaluation and recommendations for face masks in community use to reduce the transmission of respiratory infectious diseases.

BACKGROUND AND OBJECTIVE: Recommendations for the use of face masks to prevent and protect against the aerosols (≤5µm) and respiratory droplet particles (≥5µm), which can carry and transmit respiratory infections including severe acute respiratory syndrome coronavirus (SARS-CoV-2), have been in effect since the early stages of the coronavirus disease 2019 (COVID-19). The particle filtration efficiency (PFE) and air permeability are the most crucial factors affecting the level of pathogen transmission and breathability, i.e. wearer comfort, which should be investigated in detail. METHODS: In this context, this article presents a novel assessment framework for face masks combining X-ray microtomography and computational fluid dynamics simulations. In consideration to their widespread public use, two types of face masks were assessed: (I) two layer non-woven face masks and (II) the surgical masks (made out of a melt-blown fabric layer covered with two non-woven fabric layers). RESULTS: The results demonstrate that the surgical masks provide PFEs over 75% for particles with diameter over 0.1µm while two layer face masks are found out to have insufficient PFEs, even for the particles with diameter over 2µm (corresponding PFE is computed as 47.2%). Thus, existence of both the non-woven fabric layers for mechanical filtration and insertion of melt-blown fabric layer(s) for electrostatic filtration in the face masks were found to be highly critical to prevent the airborne pathogen transmission. CONCLUSIONS: The present framework would assist in computational assessment of commonly used face mask types based on their microstructural characteristics including fiber diameter, orientation distributions and fiber network density. Therefore, it would be also possible to provide new yet feasible design routes for face masks to ensure reliable personal protection and optimal breathability.

Unsupervised Learning in RSS-Based DFLT Using an EM Algorithm.

Received signal strength (RSS) changes of static wireless nodes can be used for device-free localization and tracking (DFLT). Most RSS-based DFLT systems require access to calibration data, either RSS measurements from a time period when the area was not occupied by people, or measurements while a person stands in known locations. Such calibration periods can be very expensive in terms of time and effort, making system deployment and maintenance challenging. This paper develops an Expectation-Maximization (EM) algorithm based on Gaussian smoothing for estimating the unknown RSS model parameters, liberating the system from supervised training and calibration periods. To fully use the EM algorithm's potential, a novel localization-and-tracking system is presented to estimate a target's arbitrary trajectory. To demonstrate the effectiveness of the proposed approach, it is shown that: (i) the system requires no calibration period; (ii) the EM algorithm improves the accuracy of existing DFLT methods; (iii) it is computationally very efficient; and (iv) the system outperforms a state-of-the-art adaptive DFLT system in terms of tracking accuracy.

Ultra-Low-Power Wide Range Backscatter Communication Using Cellular Generated Carrier.

With the popularization of Internet-of-things (IoT) and wireless communication systems, a diverse set of applications in smart cities are emerging to improve the city-life. These applications usually require a large coverage area and minimal operation and maintenance cost. To this end, the recently emerging backscatter communication (BC) is gaining interest in both industry and academia as a new communication paradigm that provides high energy efficient communications that may even work in a battery-less mode and, thus, it is well suited for smart city applications. However, the coverage of BC in urban area deployments is not available, and the feasibility of its utilization for smart city applications is not known. In this article, we present a comprehensive coverage study of a practical cellular carrier-based BC system for indoor and outdoor scenarios in a downtown area of a Helsinki city. In particular, we evaluate the coverage outage performance of different low-power and wide area technologies, i.e., long range (LoRa) backscatter, arrow band-Internet of Things (NB-IoT), and Bluetooth low energy (BLE) based BC at different frequencies of operation. To do so, we carry out a comprehensive campaign of simulations while using a sophisticated three-dimensional (3D) ray tracing (RT) tool, ITU outdoor model, and 3rd generation partnership project (3GPP) indoor hotspot model. This study also covers the energy harvesting aspects of backscatter device, and it highlights the importance of future backscatter devices with high energy harvesting efficiency. The simulation results and discussion provided in this article will be helpful in understanding the coverage aspects of practical backscatter communication system in a smart city environment.