Magnetic Chitosan for the Removal of Sulfamethoxazole from Tertiary Wastewaters.

Magnetic chitosan nanoparticles, synthesized by in situ precipitation, have been used as adsorbents to remove sulfamethoxazole (SMX), a sulfonamide antibiotic dangerous due to its capacity to enter ecosystems. The adsorption of SMX has been carried out in the presence of tertiary wastewaters from a depuration plant to obtain more realistic results. The effect of pH on the adsorption capacity significantly changed when carrying out the experiments in the presence of wastewater. This change has been explained while taking into account the charge properties of both the antibiotic and the magnetic chitosan. The composition of wastewaters has been characterized and discussed as regards its effect on the adsorption capacity of the magnetic chitosan. The models of Elovich and Freundlich have been selected to describe the adsorption kinetics and the adsorption isotherms, respectively. The analysis of these models has suggested that the adsorption mechanism is based on strong chemical interactions between the SMX and the magnetic chitosan, leading to the formation of an SMX multilayer.

Biogas production from anaerobic co-digestion using kitchen waste and poultry manure as substrate-part 1: substrate ratio and effect of temperature.

The rapidly declining fossil fuels are no longer able to meet the ever-increasing energy demand. Moreover, they are considered responsible for greenhouse gas (GHG) emission, contributing to the global warming. On the other hand, organic wastes, such as kitchen waste (KW) and poultry manure (PM), represent considerable pollution threat to the environment, if not properly managed. Therefore, anaerobic co-digestion of KW and PM could be a sustainable way of producing clean and renewable energy in the form of biogas while minimizing environmental impact. In this study, the anaerobic co-digestion of KW with PM was studied to assess the rate of cumulative biogas (CBG) production and methane percentage in four digester setups (D1, D2, D3, and D4) operated in batch mode. Each digester setup consisted of five parallelly connected laboratory-scale digesters having a capacity of 1 L each. The digester setups were fed with KW and PM at ratios of 1:0 (D1), 1:1 (D2), 2:1 (D3), and 3:1 (D4) at a constant loading rate of 300 mg/L with 50 gm cow manure (CM) as inoculum and were studied at both room temperature (28 °C) and mesophilic temperature (37 °C) over 24 days. The co-digestion of KW with PM demonstrated a synergistic effect which was evidenced by a 16% and 74% increase in CBG production and methane content, respectively, in D2 over D1. The D3 with 66.7% KW and 33.3% PM produced the highest CBG and methane percentage (396 ± 8 mL and 36%) at room temperature. At mesophilic condition, all the digesters showed better performance, and the highest CBG (920 ± 11 mL) and methane content (48%) were observed in D3. The study suggests that co-digestion of KW and PM at mesophilic condition might be a promising way to increase the production of biogas with better methane composition by ensuring nutrient balance, buffering capacity, and stability of the digester.

Impact of temperature, inoculum flow pattern, inoculum type, and their ratio on dry anaerobic digestion for biogas production.

This study is aimed to apply dry anaerobic digestion (DAD) for methane (CH4) enriched biogas production from unsorted organic municipal solid waste (MSW). Cumulative biogas production was monitored for 35 days of operation in batch digesters at fixed feedstock to inoculum (F/I) ratio 2. Anaerobic sludge (AS) and cow manure (CM) were used as inoculum in single and mixed modes. Several process parameters such as inoculum flow pattern (single layer, multilayer, and spiral), digestion temperature (25 to 40 °C), inoculation modes (single and mixed mode), and inoculation proportion (AS:CM = 1:1, 1:2, 1:3, and 2:1) were investigated to determine the optimum DAD conditions to maximize the CH4 laden biogas yield. The study of inoculum flow pattern showed that digester with multilayer inoculum configuration generated the maximum 555 mL cumulative biogas with the production rate of 195 mL/day (at 25 °C). Biogas production rate and cumulative biogas production were found to increase with a rise in temperature and the maximum values of 380 mL/day and 1515 mL respectively were observed at 37 °C. The mixed mode of inoculation containing AS and CM augmented the biogas yield at previously optimized conditions. Final results showed that digester with multilayer inoculum flow pattern at 37 °C produced 1850 mL cumulative biogas with 1256.58 mL CH4/kg volatile solid (VS) when the mixed inoculum was used at the AS:CM-1:2 ratio. Biogas production with this significant amount of CH4 justifies the use of the DAD process for energy (biogas) generation from widely available biomass feedstock (MSW), offering various advantages to the environment.

A novel multi-phase treatment scheme for odorous rubber effluent.

Despite the great profits of rubber latex production, its preliminary processing releases a large amount of wastewater into the water bodies from several processing steps. This rubber effluent is rich in total Kjeldahl nitrogen (TKN), total dissolved solids (TDS), biological oxygen demand (BOD) and chemical oxygen demand (COD). Therefore, the study addressed a liquid phase treatment of the effluent using an Upflow Anaerobic Sludge Blanket (UASB) reactor followed by coagu-flocculation and aeration. In addition, the gas phase (containing odorous hydrogen sulphide of 10-12% by volume) from the UASB reactor was sent to a caustic scrubber where the H2S removal efficiency of 63 ± 5% was achieved. This integrated multi-phase treatment scheme proved to be an effective approach by reducing TKN, TDS, BOD and COD by 68-87%, 61-69%, 81-84% and 81-87% respectively in the final effluent.

Microbial synergistic interactions enhanced power generation in co-culture driven microbial fuel cell.

An understanding of the inter-species relationships, especially their metabolic network in a mixed-culture system, is crucial to design an effective inoculum for enhancing the power generation of wastewater fed microbial fuel cell (MFC). In the present study, the influence of microbial mutualistic interactions on the power generation of palm oil mill effluent fed MFCs has been widely investigated by designing several co-culture and mixed culture inoculums. Among the different inoculum compositions, the highest power density of 14.8 W/m3 was achieved by Pseudomonas aeruginosa and Klebsiella variicola co-culture inoculum due to their synergistic relationships which were inter-linked via fermentation-based metabolites. Besides, the interaction of K. variicola and Bacillus cereus positively influenced the power generation resulting in a maximum power density of 11.8 W/m3 whereas the antagonistic relationship between B. cereus and P. aeruginosa resulted in a lower power generation of 1.9 W/m3. The microbial mutualistic interactions were investigated with polarization, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), as well as by using metabolite and biofilm analysis. It was observed that the synergism between bacteria enhanced power generation through the production of higher electron shuttling mediators and efficient biofilm formation as evidenced by polarization, CV and EIS analysis. In contrast, the antagonistic relationship resulted in production of cell inhibiting metabolites leading to the formation of ineffective biofilm. These findings demonstrate that the synergistic interaction between or within microorganisms is emergent in designing co-culture or mixed-culture inoculum for achieving maximum power generation in MFCs.

Evaluation of adaptive low cost solar water pasteurization device for providing safe potable water in rural households.

This study was conducted to evaluate the effectiveness of a simplified, low cost, pasteurization device in inactivating the diarrheal pathogens present in pond/lake/river water in order to provide safe potable water to people living in the rural areas of low resource countries. In this process, water in polyethylene bags was exposed to sunshine, where UV radiation emissions and heat absorption from the sunshine occurs simultaneously, and maintaining the heating at <60 °C, and minimum UV radiation emissions of 996.2 W/m2 for approximately 30 minutes was found enough to inactivate diarrheal pathogens in water. The synergistic effect of heat, UV radiation emission and holding time causes the destruction of diarrheal pathogens. However, the performance of the device depends on the thickness of the insulation and the air gap between polyethylene bags. Regardless of sample sources, the highest population reduction of Escherichia coli observed in the bacterial challenge study was 6.8 ± 0.4 log CFU/ml. The physicochemical properties were found acceptable compared with USEPA potable water quality except turbidity, which is acceptable according to the BDS standard, and the shelf-life study results demonstrated that 6 months' storage of pasteurization device-treated water at room temperature is possible without compromising water quality. Therefore, this simplified pasteurization device could be useful in potable water-scarce areas of the world.

Microbial lipid extraction from Lipomyces starkeyi using irreversible electroporation.

The aim of the study was to investigate the feasibility of using irreversible electroporation (EP) as a microbial cell disruption technique to extract intracellular lipid within short time and in an eco-friendly manner. An EP circuit was designed and fabricated to obtain 4 kV with frequency of 100 Hz of square waves. The yeast cells of Lipomyces starkeyi (L. starkeyi) were treated by EP for 2-10 min where the distance between electrodes was maintained at 2, 4, and 6 cm. Colony forming units (CFU) were counted to observe the cell viability under the high voltage electric field. The forces of the pulsing electric field caused significant damage to the cell wall of L. starkeyi and the disruption of microbial cells was visualized by field emission scanning electron microscopic (FESEM) image. After breaking the cell wall, lipid was extracted and measured to assess the efficiency of EP over other techniques. The extent of cell inactivation was up to 95% when the electrodes were placed at the distance of 2 cm, which provided high treatment intensity (36.7 kWh m-3 ). At this condition, maximum lipid (63 mg g-1 ) was extracted when the biomass was treated for 10 min. During the comparison, EP could extract 31.88% lipid while the amount was 11.89% for ultrasonic and 16.8% for Fenton's reagent. The results recommend that the EP is a promising technique for lowering the time and solvent usage for lipid extraction from microbial biomass. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 34:838-845, 2018.

Technical difficulties and solutions of direct transesterification process of microbial oil for biodiesel synthesis.

Microbial oils are considered as alternative to vegetable oils or animal fats as biodiesel feedstock. Microalgae and oleaginous yeast are the main candidates of microbial oil producers' community. However, biodiesel synthesis from these sources is associated with high cost and process complexity. The traditional transesterification method includes several steps such as biomass drying, cell disruption, oil extraction and solvent recovery. Therefore, direct transesterification or in situ transesterification, which combines all the steps in a single reactor, has been suggested to make the process cost effective. Nevertheless, the process is not applicable for large-scale biodiesel production having some difficulties such as high water content of biomass that makes the reaction rate slower and hurdles of cell disruption makes the efficiency of oil extraction lower. Additionally, it requires high heating energy in the solvent extraction and recovery stage. To resolve these difficulties, this review suggests the application of antimicrobial peptides and high electric fields to foster the microbial cell wall disruption.

Efficacy of Probiotics Versus Placebo in the Prevention of Necrotizing Enterocolitis in Preterm Very Low Birth Weight Infants: A Double-Blind Randomized Controlled Trial.

OBJECTIVE: To evaluate the efficacy of orally administered probiotics in preventing necrotizing enterocolitis (NEC) in preterm very low birth weight (VLBW) infants. STUDY DESIGN: Arandomized double blind controlled trial. PLACE AND DURATION OF STUDY: The Paediatrics Department of Sylhet M.A.G. Osmani Medical College Hospital, Sylhet Bangladesh, from July 2012 to June 2015. METHODOLOGY: Preterm (28 - 33 weeks gestation) VLBW (birth weight 1000 - 1499 g) neonates were enrolled. The study group was fed with probiotics once daily with breast milk from first feeding, and the control group with only breast milk without the addition of probiotics. Both the groups received other standard care. The primary outcome was the development of NEC (stage II and III), categorized by modified Bell's classification. RESULTS: In 108 neonates, development of NEC was significantly lower in the study group than that of control group [1 (1.9%) vs. 6 (11.5%); p=0.044]. Age of achievement of full oral feeding was significantly earlier in the study group than that in the control group (14.88 ±3.15 and 18.80 ±4.32 days; p < 0.001). Duration of hospital stay was significantly short in the study group compared to the control group (15.82 ±2.94 days vs. 19.57 ±4.26 days; p < 0.001). CONCLUSION: Probiotic supplementation reduces the frequency of necrotising enterocolitis in preterm neonates with very low birth weight. It is also associated with faster achievement of full oral feeding and short duration of hospital stay.

Biodiesel from lignocellulosic biomass--prospects and challenges.

Biodiesel can be a potential alternative to petroleum diesel, but its high production cost has impeded its commercialization in most parts of the world. One of the main drivers for the generation and use of biodiesel is energy security, because this fuel can be produced from locally available resources, thereby reducing the dependence on imported oil. Many countries are now trying to produce biodiesel from plant or vegetable oils. However, the consumption of large amounts of vegetable oils for biodiesel production could result in a shortage in edible oils and cause food prices to soar. Alternatively, the use of animal fat, used frying oils, and waste oils from restaurants as feedstock could be a good strategy to reduce the cost. However, these limited resources might not meet the increasing demand for clean, renewable fuels. Therefore, recent research has been focused the use of residual materials as renewable feedstock in order to lower the cost of producing biodiesel. Microbial oils or single cell oils (SCOs), produced by oleaginous microorganisms have been studied as promising alternatives to vegetable or seed oils. Various types of agro-industrial residues have been suggested as prospective nutritional sources for microbial cultures. Since the most abundant residue from agricultural crops is lignocellulosic biomass (LCB), this byproduct has been given top-priority consideration as a source of biomass for producing biodiesel. But the biological transformation of lignocellulosic materials is complicated due to their crystalline structure. So, pretreatment is required before they can be converted into fermentable sugar. This article compares and scrutinizes the extent to which various microbes can accumulate high levels of lipids as functions of the starting materials and the fermentation conditions. Also, the obstacles associated with the use of LCB are described, along with a potentially viable approach for overcoming the obstacles that currently preclude the commercial production of biodiesel from agricultural biomass.

Remediation of waters contaminated with MCPA by the yeasts Lipomyces starkeyi entrapped in a sol-gel zirconia matrix.

A single-stage sol-gel route was set to entrap yeast cells of Lipomyces starkeyi in a zirconia (ZrO(2)) matrix, and the remediation ability of the resulting catalyst toward a phenoxy acid herbicide, 4-chloro-2-methylphenoxyacetic acid (MCPA), was studied. It was found that the experimental procedure allowed a high dispersion of the microorganisms into the zirconia gel matrix; the ZrO(2) matrix exhibited a significant sorption capacity of the herbicide, and the entrapped cells showed a degradative activity toward MCPA. The combination of these effects leads to a nearly total removal efficiency (>97%) of the herbicide at 30 °C within 1 h incubation time from a solution containing a very high concentration of MCPA (200 mg L(-1)). On the basis of the experimental evidence, a removal mechanism was proposed involving in the first step the sorption of the herbicide molecules on the ZrO(2) matrix, followed by the microbial degradation operated by the entrapped yeasts, the metabolic activity of which appear enhanced under the microenvironmental conditions established within the zirconia matrix. Repeated batch tests of sorption/degradation of entrapped Lipomyces showed that the removal efficiency retained almost the same value of 97.3% after 3 batch tests, with only a subsequent slight decrease, probably due to the progressive saturation of the zirconia matrix.

Microbial conversion of olive oil mill wastewaters into lipids suitable for biodiesel production.

Lipomyces starkey were able to survive and proliferate in the presence of olive oil mill wastewaters (OMW), a medium difficult to process by biological treatments, due to the antimicrobial activities of their phenolic components. The microorganisms were grown in the presence of undiluted OMW, without external organic supplements, producing a significant reduction of both the total organic carbon (TOC) and the total phenols content. The OMW treated by L. starkey showed a significant increase of the germination index. The preliminary dilution of OMW enhanced the reduction of polluting components of OMW, leading to a complete TOC removal, as well as to lower levels of residual phenols. The activities of extracellular lipases and esterases significantly increased in the course of the OMW fermentation. A significant increase in lipid yield was observed in L. starkey in the course of the OMW treatment, particularly enhanced when the feedstock was preliminarily diluted. The fatty acid distribution showed a prevalence of oleic acid, demonstrating the potential of L. starkeyi as a source of lipids to be used as a feedstock for the synthesis of II generation biodiesel.