Enhanced Durability and Antireflective Performance of Ag-Based Transparent Conductors Achieved via Controlled N-Doping.

Ag-based transparent conductors (TCs) are often proposed as an alternative to ITO coatings. However, while their performance has been widely demonstrated, their environmental durability is frequently overlooked or addressed with the use of highly specific encapsulating layers. In this work, the durability and antireflective performance of Ag-based TCs are simultaneously enhanced. To do so, a transfer matrix modeling approach is used to determine the general requirements for high performance antireflective properties as a function of Ag thickness and dielectric refractive indices, offering more widely applicable insight into stack optimization. Coating durability is investigated as a function of the Ag microstructure, which is modified by altering the N2 concentration used for doping of the Ag layer and the selection of the seed layer. Increasing N2 concentration during Ag deposition was found to decrease grain size and durability of Ag coatings deposited on Si3N4 whereas all coatings on ZnO(Al) showed higher stability. Significantly higher durability is found when specifically combining intermediate N2 concentrations in the sputtering gas mixture (Ag(N):5%, compared to 0% and 50%) and a ZnO(Al) seed layer, and a mechanism accounting for this increased durability is proposed. The addition of NiCrNx protective coatings increases the system durability without altering these trends. These findings are combined to fabricate a highly performant Ag-based TC (TV = 89.2%, RVFS = 0.23%, 21.4 Ω), which shows minimal property changes following corrosion testing by immersion in a heated and highly concentrated aqueous NaCl solution (200 g/L, 50 °C).

Spectral effects and enhancement quantification in healthy human saliva with surface-enhanced Raman spectroscopy using silver nanopillar substrates.

OBJECTIVES: Raman spectroscopy as a diagnostic tool for biofluid applications is limited by low inelastic scattering contributions compared to the fluorescence background from biomolecules. Surface-enhanced Raman spectroscopy (SERS) can increase Raman scattering signals, thereby offering the potential to reduce imaging times. We aimed to evaluate the enhancement related to the plasmonic effect and quantify the improvements in terms of spectral quality associated with SERS measurements in human saliva. METHODS: Dried human saliva was characterized using spontaneous Raman spectroscopy and SERS. A fabrication protocol was implemented leading to the production of silver (Ag) nanopillar substrates by glancing angle deposition. Two different imaging systems were used to interrogate saliva from 161 healthy donors: a custom single-point macroscopic system and a Raman micro-spectroscopy instrument. Quantitative metrics were established to compare spontaneous RS and SERS measurements: the Raman spectroscopy quality factor (QF), the photonic count rate (PR), the signal-to-background ratio (SBR). RESULTS: SERS measurements acquired with an excitation energy four times smaller than with spontaneous RS resulted in improved QF, PR values an order of magnitude larger and a SBR twice as large. The SERS enhancement reached 100×, depending on which Raman bands were considered. CONCLUSIONS: Single-point measurement of dried saliva with silver nanopillars substrates led to reproducible SERS measurements, paving the way to real-time tools of diagnosis in human biofluids.

Fabrication of Plasmonic Indium Tin Oxide Nanoparticles by Means of a Gas Aggregation Cluster Source.

In this work, we demonstrate, for the first time, the possibility to fabricate indium tin oxide nanoparticles (ITO NPs) using a gas aggregation cluster source. A stable and reproducible deposition rate of ITO NPs has been achieved using magnetron sputtering of an In2O3/SnO2 target (90/10 wt %) at an elevated pressure of argon. Remarkably, most of the generated NPs possess a crystalline structure identical to the original target material, which, in combination with their average size of 17 nm, resulted in a localized surface plasmon resonance peak at 1580 nm in the near-infrared region.

Optical and tribomechanical stability of optically variable interference security devices prepared by dual ion beam sputtering.

Optical security devices applied to banknotes and other documents are exposed to different types of harsh environments involving the cycling of temperature, humidity, chemical agents, and tribomechanical intrusion. In the present work, we study the stability of optically variable devices, namely metameric interference filters, prepared by dual ion beam sputtering onto polycarbonate and glass substrates. Specifically, we assess the color difference as well as the changes in the mechanical properties and integrity of all-dielectric and metal-dielectric systems due to exposure to bleach, detergent and acetone agents, and heat and humidity. The results underline a significant role of the substrate material, of the interfaces, and of the nature and microstructure of the deposited films in long term stability under everyday application conditions.

Mechanical and thermoelastic characteristics of optical thin films deposited by dual ion beam sputtering.

Mechanical and thermoelastic properties of optical films are very important to ensure the performance of optical interference filters and optical coating systems. We systematically study the growth and the mechanical and thermoelastic characteristics of niobium oxide (Nb(2)O(5)), tantalum oxide (Ta(2)O(5)), and silicon dioxide (SiO(2)) thin films prepared by dual ion beam sputtering. First, we investigate the stress (sigma), hardness (H), reduced Young's modulus (E(r)), and scratch resistance. Second, we focus on the methodology and assessment of the coefficient of thermal expansion (CTE) and Poisson's ratio (nu) using the two-substrate method. For the high refractive index films, namely, Nb(2)O(5) (n at 550 nm=2.30) and Ta(2)O(5) (n at 550 nm=2.13), we obtained H approximately 6 GPa, E(r) approximately 125 GPa, CTE=4.9x10(-6) degrees C(-1), nu=0.22, and H approximately 7 GPa, E(r) approximately 133 GPa, CTE=4.4x10(-6) degrees C(-1), and nu=0.27, respectively. In comparison, for SiO(2) (n at 550 nm=1.48), these values are H approximately 9.5 GPa, E(r) approximately 87 GPa, CTE=2.1x10(-6) degrees C(-1), and nu=0.11. Correlations between the growth conditions (secondary beam ion energy and ion current), the microstructure, and the film properties are discussed.

Solid emulsion gel as a novel construct for topical applications: synthesis, morphology and mechanical properties.

A series of the solid emulsion gels with the oil volume fraction in the range of 0-50% were synthesized through a polycondensation reaction between activated p-nitrophenyl carbonate poly(ethylene glycol) and protein-stabilized oil-in-water emulsions. The resultant structures were investigated in terms of swelling behavior, composition, morphology, mechanical and skin hydration properties. Solid emulsions gels share the properties of both hydrogel and emulsion. Similar to the classical hydrogel, the SEG swells in water up to equilibrium swelling degree, which decreases as the oil volume fraction increases, and comprises immobilized drops of protein-stabilized oil. The impregnation of the oil phase is found to reduce tensile stiffness of the material, but improves material's extensibility. The mechanical properties of the constructs (Young moduli in the range of 9-15 kPa and the elongation at break of 120-220%) are interpreted according to the "rule of elasticity mixture" that considers the elasticity of the composite material to be a sum of the contributions from individual components, i.e. hydrogel and dispersed oil drops. An idealized model that takes into account the history of the material preparation has been proposed to explain the improved extensibility of the constructs. The results of the mechanical tests, equilibrium swelling, and the skin hydration effect of the solid emulsion gels in vivo are discussed from the perspective of the biomedical applications of the solid emulsion gels, in particular, for the transdermal delivery of hydrophilic and lipophilic drugs.

Mechanical and microstructural properties of hybrid poly(ethylene glycol)-soy protein hydrogels for wound dressing applications.

Biomimetic hydrogel made of poly(ethylene glycol) and soy protein with a water content of 96% has been developed for moist wound dressing applications. In this study, such hybrid hydrogels were investigated by both tensile and unconfined compression measurements in order to understand the relationships between structural parameters of the network, its mechanical properties and protein absorption in vitro. Elastic moduli were found to vary from 1 to 17 kPa depending on the composition, while the Poisson's ratio (approximately 0.18) and deformation at break (approximately 300%) showed no dependence on this parameter. Further calculations yielded the crosslinking concentration, the average molecular weight between crosslinks (M(C)) and the mesh size. The results show that reactions between PEG and protein create polymeric chains comprising molecules of PEG and protein fragments between crosslinks. M(C) is three times higher than that expected for a "theoretical network." On the basis of this data, we propose a model for the 3D network of the hydrogel, which is found to be useful for understanding drug release properties and biomedical potential of the studied material.

Single-material inhomogeneous optical filters based on microstructural gradients in plasma-deposited silicon nitride.

Transparent hydrogenated amorphous silicon nitride (SiNx:H) coatings were prepared by dual-mode microwave-radio-frequency plasma-enhanced chemical vapor deposition. By controlling the effects of plasma density and ion energy on the film growth, it was possible to modify the microstructure of the coatings and hence the refractive index n. Using this method, we were able to vary n from 1.6 to 2.0, at 550 nm, by adjusting the power levels of the radio-frequency and microwave components while keeping the gas composition (SiH4, N2) and pressure constant. An inhomogeneous bandpass filter with a controlled refractive-index depth profile was fabricated, and its optical performance was compared with that of its multilayer counterpart. Besides the attractive optical features of such single-material rugate filters, we found that the mechanical resistance of inhomogeneous films is superior to that of multilayer systems.