Magnetic Properties of a High-Pressure Torsion Deformed Co-Zr Alloy.

Co-Zr amorphous alloys exhibit soft magnetic properties, whereas the Co-rich crystalline magnetic phases in this alloy system displayed a hard magnetic behavior. In this study, an initial two-phase Co-Zr composite with an overall composition of 75 at.% Co and 25 at.% Zr was processed by high-pressure torsion (HPT), and the effects of severe plastic deformation and subsequent thermal treatment on the composite's structural evolution and its magnetic properties were investigated. HPT processing allowed us to achieve an amorphous microstructure with low coercivity in its as-deformed state. To further tune the alloy's magnetic properties and study its crystallization behavior, various annealed states were investigated. The microstructural properties were correlated with the magnetic properties, and a decreasing coercivity with increasing annealing temperatures was observed despite the onset of crystallization in the amorphous alloy. At higher annealing temperatures, coercivity increased again. The results appear promising for obtaining tuneable rare-earth free magnetic materials by severe plastic deformation.

Exchange Bias Demonstrated in Bulk Nanocomposites Processed by High-Pressure Torsion.

Ferromagnetic (Fe or Fe20Ni80) and antiferromagnetic (NiO) phases were deformed by high-pressure torsion, a severe plastic deformation technique, to manufacture bulk-sized nanocomposites and demonstrate an exchange bias, which has been reported predominantly for bilayer thin films. High-pressure torsion deformation at elevated temperatures proved to be the key to obtaining homogeneous bulk nanocomposites. X-ray diffraction investigations detected nanocrystallinity of the ferromagnetic and antiferromagnetic phases. Furthermore, an additional phase was identified by X-ray diffraction, which formed during deformation at elevated temperatures through the reduction of NiO by Fe. Depending on the initial powder composition of Fe50NiO50 or Fe10Ni40NiO50 the new phase was magnetite or maghemite, respectively. Magnetometry measurements demonstrated an exchange bias in high-pressure torsion-processed bulk nanocomposites. Additionally, the tailoring of magnetic parameters was demonstrated by the application of different strains or post-process annealing. A correlation between the amount of applied strain and exchange bias was found. The increase of exchange bias through applied strain was related to the microstructural refinement of the nanocomposite. The nanocrystalline maghemite was considered to have a crucial impact on the observed changes of exchange bias through applied strain.

Interfacial Morphology and Effects on Device Performance of Organic Bilayer Heterojunction Solar Cells.

The effects of interface roughness between donor and acceptor in a bilayer heterojunction solar cell were investigated on a polymer-polymer system based on poly(3-hexylthiophene) (P3HT) and poly(dioctylfluorene-alt-benzothiadiazole) (F8BT). Both polymers are known to reorganize into semicrystalline structures when heated above their glass-transition temperature. Here, the bilayers were thermally annealed below glass transition of the bulk polymers (≈140 °C) at temperatures of 90, 100, and 110 °C for time periods from 2 min up to 250 min. No change of crystallinity could be observed at those temperatures. However, X-ray reflectivity and device characteristics reveal a coherent trend upon heat treatment. In X-ray reflectivity investigations, an increasing interface roughness between the two polymers is observed as a function of temperature and annealing time, up to a value of 1 nm. Simultaneously, according bilayer devices show an up to 80% increase of power conversion efficiency (PCE) for short annealing periods at any of the mentioned temperatures. Together, this is in agreement with the expectations for enlargement of the interfacial area. However, for longer annealing times, a decrease of PCE is observed, despite the ongoing increase of interface roughness. The onset of decreasing PCE shifts to shorter durations the higher the annealing temperature. Both, X-ray reflectivity and device characteristics display a significant change at temperatures below the glass transition temperatures of P3HT and F8BT.

Particular film formation of phenytoin at silica surfaces.

Given the increasing number of poorly soluble and thus poorly bioavailable active pharmaceutical materials, there is a demand for innovative formulation platforms for such molecules. Thus a focus on enhancing dissolution properties of poorly soluble drugs exists. Within this study, the spin coating of acetone solutions containing 5,5-diphenyl-2,4-imidazolidinedione (phenytoin) in various concentrations is evaluated. The results reveal strong variations of the morphology of deposited phenytoin crystals at silica surfaces. Individual separated particles are obtained on low phenytoin concentrations, and closely packed particular films form when the concentration is increased. As the material is isomorphic, these various morphologies have the same crystalline structure. Dissolution experiments reveal that both the apparent maximum solubility and as the dissolution rate are strongly enhanced compared to bulk powder, suggesting that formulation based on this preparative technique will allow overcoming the low solubility problematic for a variety of drugs.