RESUMO
Self-powered photodetectors (PD) based on ferroelectric materials have gained huge attention because of the spontaneous polarization and unique photovoltaic effect. However, the low photocurrent values and switch ratio of the ferroelectric materials limit their further practical applications in a wide temperature range. In this study, the self-powered ZnO nanofiber array/BaTiO3 (ZnO-NFA/BTO) PD was fabricated by high-ordered ZnO-NFA via electrospinning method deposited on a 300 nm BTO film synthesized using sol-gel method. The electrospinning can prepare ZnO-NFAs with a controllable diameter (100 nm) and orientation and is directly deposited on the quartz at a large scale, which simplifies the fabrication process. This device possesses a greater on/off ratio of 2357 at zero bias than that of BTO PD (3.33) and the ZnO-NFA PD (125) at 0.2 V. The highest responsivity and specific detectivity are 1.41 mA W-1 and 1.48 × 109 Jones at 368 nm under 0 V bias, respectively, which is enhanced about three magnitudes than the pristine BTO PD (1.21 µA W-1 and 1.02 × 109 Jones). The photocurrent of the ZnO-NFA/BTO PD strongly depends on the temperature. After the cooling system and prepolarization processing are both introduced, the largest light current (475 nA) and photovoltaic plateaus (585 nA) are enhanced by about 4417 and 4278% under 368 nm at a power intensity of 4.46 mW cm-2 at 0 °C, respectively. The enhancement of photocurrent is associated with a ferro-pyro-phototronic effect, evidenced by enhanced ferroelectric polarization. The ZnO-NFA/BTO PD can detect weak signals at low power intensity with a wide temperature range of 0-100 °C under 0 V bias. The self-powered ZnO-NFA/BTO PD provides a new and promising way to fabricate high-performance and low-cost photodetectors from inorganic perovskite materials.
RESUMO
Higher pressure die casting (HPDC) AM series (Mg-Al-Mn) Mg alloys have wide application potential in the automobile industry. To promote its application, systematic investigation on the corrosion performance and corrosion residual strength of HPDC AM50+1Ce and AM60 was carried out. The corrosion of HPDC AM50+1Ce was more uniform, while the pitting corrosion of AM60 was more severe, and the mechanical properties of HPDC AM60 was more sensitive to corrosion. The residual strength of AM50+1Ce and AM60 after corrosion of 648 h was 199 MPa and 183 MPa, respectively. The findings can contribute to a better understanding of the corrosion and residual strength of HPDC AM series Mg alloys.
RESUMO
A newly developed Mg-2Gd-0.5Zr-xZn (x = 0.5, 1.0, 2.0, 3.0 wt %) alloy system exhibits significant strengthening by doping with Zn. In order to understand the strengthening mechanism, the microstructure, texture evolution, and mechanical properties of ultrahigh ductility Mg-2Gd-0.5Zr alloys with a Zn addition were systematically investigated. The addition of Zn results in the formation of Mg-Gd-Zn intermetallic compounds along grain boundaries, which encourages grain refinement during hot extrusion via the particle stimulated nucleation (PSN) mechanism. Furthermore, during texture sharpening the pole changes from <20 2 ¯ 1> to <01 1 ¯ 0>, which also occurred in the extruded alloys with Zn addition, which is unfavorable for the basal slip and tensile twinning. Mg-2Gd-0.5Zr-3Zn shows well-balanced strength and ductility with a tensile yield strength (YS) and ultimate tensile strength (UTS) of 285 and 314 MPa, accompanied by a high tensile elongation of 24%. They are superior to those of commercial AZ31. The enhanced strength is attributed to grain refinement, precipitation strengthening, and texture sharpening induced by alloying with Zn. The research result is also of great value to the development of low rare-earth, high strength, and high room temperature ductility magnesium alloy.
RESUMO
Nine kinds of rare-earth free Mg-Al-Sn-Mn magnesium alloys were designed by orthogonal method. Scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and tension tests were carried out to investigate the microstructures and mechanical properties. As-cast Mg-Al-Sn-Mn alloys have an obvious dendritic structure that is composed of α-Mg, Mg17Al12, and Mg2Sn phases. After hot extrusion, the cast dendrite structure changed into a recrystallized equiaxed grain. Mg17Al12 dissolved completely into a matrix, and only α-Mg, Mg2Sn, and a few Al-Mn phases could be observed. The influence of three alloy elements (Al, Sn, and Mn) on grain size, texture intensity, ultimate tensile strength (UTS), tensile yield strength (TYS), and elongation (EL) were studied by extreme difference analysis method. The content of Mn had the greatest influence on grain size. The AT61-0.2Mn and AT73-0.2Mn alloys had the smallest grain, reaching 6.8 µm. The content of Al had the greatest influence on the strength; therefore, the AT73-0.2Mn alloy had the highest UTS, 322 MPa, and TYS, 202 MPa. The content of Sn had the greatest influence on elongation. The AT52-0.4Mn alloy had the highest elongation in theory, but it was not included in the nine designed kinds of alloys yet. AT52-0.2Mn alloy had the highest elongation in the nine alloys (28.4%).
RESUMO
A hydrophobic coating was fabricated on the surface of magnesium alloy using a simple one-step hydrothermal method with the use of environmentally friendly agent. Scanning electron microscopy, energy-dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and contact angle test were used to characterize the surfaces. Corrosion behavior in a 3.5wt.% NaCl solution was evaluated using OCP time curves test, potentiodynamic polarization test and EIS analysis. The findings show that the substrate is covered by the coating of magnesium hydroxide and magnesium stearate, reaching a contact angle of around 146°. Corrosion behavior show huge improvement, the progress with increase of treatment time could be related to the increased growth rate of coating.