A third-order mode high frequency biosensor with atomic resolution.

An atomic resolution ultra-high sensitivity surface acoustic wave (SAW) biosensor for DNA sequences and cells detection is proposed. Interdigitated transducers (IDTs) fabricated on LiNbO3 substrate achieve a high quality factor (Q) of over 4000 at a frequency of 6.4 GHz (third-order harmonic mode) using an optimized design and process. The biosensor shows excellent linear responses to target DNA in the range from 1 µg/ml to 1 ng/ml with a high sensitivity of 6.7 × 10(-16)g/cm(2)/Hz, hence the difference of a single hybridized DNA base can also be distinguished. With such a high mass resolution, the biosensor is capable of quantitative detection of living cancer cells. The frequency responses of single mouse mammary adenocarcinoma (EMT6) cell and mouse fibroblast (3T3) cell are studied. The interferences in the experiments show insignificant influence on the frequency shift, which verifies the high selectivity of the biosensor. The biosensor is also able to repeat the sensing ability after rough cleaning, therefore cost reduction is achieved from the recycling process in practical applications. The detection limit is defined from the noise analysis of the device, atomic resolution is realized according to the calculation, thereby initiating a potential tool for high-precision medical diagnoses and phenomena observation at the atomic-level.

An ultra-high element density pMUT array with low crosstalk for 3-D medical imaging.

A ~1 MHz piezoelectric micromachined ultrasonic transducer (pMUT) array with ultra-high element density and low crosstalk is proposed for the first time. This novel pMUT array is based on a nano-layer spin-coating lead zirconium titanium film technique and can be fabricated with high element density using a relatively simple process. Accordingly, key fabrication processes such as thick piezoelectric film deposition, low-stress Si-SOI bonding and bulk silicon removal have been successfully developed. The novel fine-pitch 6 × 6 pMUT arrays can all work at the desired frequency (~1 MHz) with good uniformity, high performance and potential IC integration compatibility. The minimum interspace is ~20 µm, the smallest that has ever been achieved to the best of our knowledge. These arrays can be potentially used to steer ultrasound beams and implement high quality 3-D medical imaging applications.

Laser directed lithography of asymmetric graphene ribbons on a polydimethylsiloxane trench structure.

Recently, manipulating heat transport by asymmetric graphene ribbons has received significant attention, in which phonons in the carbon lattice are used to carry energy. In addition to heat control, asymmetric graphene ribbons might also have broad applications in renewable energy engineering, such as thermoelectric energy harvesting. Here, we transfer a single sheet of graphene over a 5 µm trench of polydimethylsiloxane (PDMS) structure. By using a laser (1.77 mW, 1 µm diameter spot size, 517 nm wavelength) focusing on one side of the suspended graphene, a triangular shaped graphene ribbon is obtained. As the graphene has a negative thermal expansion coefficient, local laser heating could make the affected graphene area shrink and eventually break. Theoretical calculation shows that the 1.77 mW laser could create a local hot spot as high as 1462.5 °C, which could induce an asymmetric shape structure. We also find the temperature coefficient (-13.06 cm(-1) mW) of suspended graphene on PDMS trench substrate is ten times higher than that reported on SiO2/Si trench substrate. Collectively, our results raise the exciting prospect that the realization of graphene with asymmetric shape on thermally insulating substrate is technologically feasible, which may open up important applications in thermal circuits and thermal management.

A novel flexible capacitive touch pad based on graphene oxide film.

Recently, graphene oxide (GO) supercapacitors with ultra-high energy densities have received significant attention. In addition to energy storage, GO capacitors might also have broad applications in renewable energy engineering, such as vibration and sound energy harvesting. Here, we experimentally create a macroscopic flexible capacitive touch pad based on GO film. An obvious touch "ON" to "OFF" voltage ratio up to ∼60 has been observed. Moreover, we tested the capacitor structure on both flat and curved surfaces and it showed high response sensitivity under fast touch rates. Collectively, our results raise the exciting prospect that the realization of macroscopic flexible keyboards with large-area graphene based materials is technologically feasible, which may open up important applications in control and interface design for solar cells, speakers, supercapacitors, batteries and MEMS systems.

A novel solid-state thermal rectifier based on reduced graphene oxide.

Recently, manipulating heat transport by phononic devices has received significant attention, in which phonon--a heat pulse through lattice, is used to carry energy. In addition to heat control, the thermal devices might also have broad applications in the renewable energy engineering, such as thermoelectric energy harvesting. Elementary phononic devices such as diode, transistor and logic devices have been theoretically proposed. In this work, we experimentally create a macroscopic scale thermal rectifier based on reduced graphene oxide. Obvious thermal rectification ratio up to 1.21 under 12 K temperature bias has been observed. Moreover, this ratio can be enhanced further by increasing the asymmetric ratio. Collectively, our results raise the exciting prospect that the realization of macroscopic phononic device with large-area graphene based materials is technologically feasible, which may open up important applications in thermal circuits and thermal management.

Static behavior of a graphene-based sound-emitting device.

Due to the extremely high thermal conductivity and low heat capacity per unit area of graphene, it is possible to fabricate an efficient sound-emitting device based on the thermoacoustic effect with no mechanical vibration. In this paper, the fundamental performance of this new graphene sound-emitting device (G-SED) is investigated in terms of its static behavior. The sound amplitude mapping shows that the G-SED has good sound performance under 0.01 W. The sound frequency spectra measured at different distances and angles show that the G-SED has good sound directivity. It is possible to realize sound wave manipulation by using an array of G-SEDs. The relationship between the temperature of graphene and the sound frequency was investigated by a thermal imaging instrument. The fast transient sound response in real time was recorded by applying 60 µs short time multi-pulses and single-pulse. The stable sound emission at a constant sound pressure amplitude with low noise was observed for continuous operation under a fixed frequency over several hours. Such significant performances in this G-SED indicate broad applications, and shed light on the use of graphene in the field of acoustics.

Single-layer graphene sound-emitting devices: experiments and modeling.

Single-layer graphene (SLG) was demonstrated to emit sound. The sound emission from SLG had a significant flat frequency response in the wide ultrasound range from 20 kHz to 50 kHz. SLG can produce a sound pressure level (SPL) as high as 95 dB at a distance of 5 cm with a sound frequency of 20 kHz. The SPL value is among the highest reported to date for sound-emitting devices (SEDs) based on the thermoacoustic effect. A theoretical model was established to analyze the sound emission from SLG. The theoretical results are in good agreement with the experimental results. Conventional acoustic devices with a large size can be reduced to the nano-scale by using this novel SLG-SED material. It has the potential to be widely used in speakers, buzzers, earphones, ultrasonic transducer, etc.

Graphene-on-paper sound source devices.

We demonstrate an interesting phenomenon that graphene can emit sound. The application of graphene can be expanded in the acoustic field. Graphene-on-paper sound source devices are made by patterning graphene on paper substrates. Three graphene sheet samples with the thickness of 100, 60, and 20 nm were fabricated. Sound emission from graphene is measured as a function of power, distance, angle, and frequency in the far-field. The theoretical model of air/graphene/paper/PCB board multilayer structure is established to analyze the sound directivity, frequency response, and efficiency. Measured sound pressure level (SPL) and efficiency are in good agreement with theoretical results. It is found that graphene has a significant flat frequency response in the wide ultrasound range 20-50 kHz. In addition, the thinner graphene sheets can produce higher SPL due to its lower heat capacity per unit area (HCPUA). The infrared thermal images reveal that a thermoacoustic effect is the working principle. We find that the sound performance mainly depends on the HCPUA of the conductor and the thermal properties of the substrate. The paper-based graphene sound source devices have highly reliable, flexible, no mechanical vibration, simple structure and high performance characteristics. It could open wide applications in multimedia, consumer electronics, biological, medical, and many other areas.