Optimization of Weight Ratio for DSPE-PEG/TPGS Hybrid Micelles to Improve Drug Retention and Tumor Penetration.

PURPOSE: To enhance therapeutic efficacy and prevent phlebitis caused by Asulacrine (ASL) precipitation post intravenous injection, ASL-loaded hybrid micelles with size below 40 nm were developed to improve drug retention and tumor penetration. METHODS: ASL-micelles were prepared using different weight ratios of 1,2-distearoyl-sn-glycero-3-phosphoethanolamine-polyethyleneglycol-2000 (DSPE-PEG2000) and D-α-tocopheryl polyethylene glycol 1000 succinate (TPGS) polymers. Stability of micelles was optimized in terms of critical micelle concentration (CMC) and drug release properties. The encapsulation efficiency (EE) and drug loading were determined using an established dialysis-mathematic fitting method. Multicellular spheroids (MCTS) penetration and cytotoxicity were investigated on MCF-7 cell line. Pharmacokinetics of ASL-micelles was evaluated in rats with ASL-solution as control. RESULTS: The ASL-micelles prepared with DSPE-PEG2000 and TPGS (1:1, w/w) exhibited small size (~18.5 nm), higher EE (~94.12%), better sustained in vitro drug release with lower CMC which may be ascribed to the interaction between drug and carriers. Compared to free ASL, ASL-micelles showed better MCTS penetration capacity and more potent cytotoxicity. Pharmacokinetic studies demonstrated that the half-life and AUC values of ASL-micelles were approximately 1.37-fold and 3.49-fold greater than that of free ASL. CONCLUSIONS: The optimized DSPE-PEG2000/TPGS micelles could serve as a promising vehicle to improve drug retention and penetration in tumor.

Optimization of the formation of embedded multicellular spheroids of MCF-7 cells: How to reliably produce a biomimetic 3D model.

To obtain a multicellular MCF-7 spheroid model to mimic the three-dimensional (3D) of tumors, the microwell liquid overlay (A) and hanging-drop/agar (B) methods were first compared for their technical parameters. Then a method for embedding spheroids within collagen was optimized. For method A, centrifugation assisted cells form irregular aggregates but not spheroids. For method B, an extended sedimentation period of over 24 h for cell suspensions and increased viscosity of the culture medium using methylcellulose were necessary to harvest a dense and regular cell spheroid. When the number was less than 5000 cells/drop, embedded spheroids showed no tight cores and higher viability than the unembedded. However, above 5000 cells/drop, cellular viability of embedded spheroids was not significantly different from unembedded spheroids and cells invading through the collagen were in a sun-burst pattern with tight cores. Propidium Iodide staining indicated that spheroids had necrotic cores. The doxorubicin cytotoxicity demonstrated that spheroids were less susceptible to DOX than their monolayer cells. A reliable and reproducible method for embedding spheroids using the hanging-drop/agarose method within collagen is described herein. The cell culture model can be used to guide experimental manipulation of 3D cell cultures and to evaluate anticancer drug efficacy.

In vitro release of cupric ion from intrauterine devices: influence of frame, shape, copper surface area and indomethacin.

The release of cupric ion from copper intrauterine device (Cu-IUD) in human uterus is essential for contraception. However, excessive cupric ion will cause cytotoxic effect. In this paper, we investigated the influence of device characteristics (frame, copper surface area, shape, copper type and indomethacin) on copper release for the efficacy and adverse effects vary with IUD types which may correlate to their different release behaviors. Nine types of Cu-IUDs were selected and incubated in simulated uterine fluid. They were paired for comparison based on the device properties and the release of cupric ion was determined by flame atomic absorption spectrometer for about 160 days. The result showed that there was a burst release during the first month and the release rate tends to slow down and become steady afterwards. In addition, the copper release was mainly influenced by frame, indomethacin and copper type (copper wire and copper sleeve) while the shape variation had little effect on copper release throughout the experiment. Moreover, the influence of copper surface area was only noticeable during the first month. These findings were seldom reported before and may provide some useful information for the design of Cu-IUDs.