Luminescence and Formation of Cubic and Hexagonal (K,Rb)2SiF6:Mn4.

The efficient red-emitting phosphor K2SiF6:Mn4+ (KSF) is widely used for low-power LED applications. The saturated red color and sharp line emission are ideal for application in backlight LEDs for displays. However, the long excited state lifetime lowers the external quantum yield (EQY) at high photon flux, limiting the application in (higher power density) lighting. Here, we report the synthesis of a new crystalline phase: hexagonal (K,Rb)SiF6:Mn4+ (h-KRSF). Due to the lower local symmetry, the Mn4+ emission in this new host material shows a pronounced zero phonon line, which is different from Mn4+ in the cubic KSF. The lower symmetry reduces the excited state lifetime, and thus, the loss of EQY under high photon fluxes, and the spectral change also increases the lumen/W output. Temperature-dependent emission and lifetime measurements reveal a high luminescence quenching temperature of ∼500 K, similar to that of KSF. The formation mechanism of h-KRSF was studied in situ by measuring the emission spectra of the precipitate in solution over time. Initially, nanocrystalline cubic KRSF (c-KRSF) is formed, which transforms into a microcrystalline hexagonal precipitate with a surprising exponential increase in the transformation rate with time. The stability of the new phase was studied by temperature-dependent XRD, and an irreversible transition back to the cubic phase was seen upon heating to temperatures above 200 °C.

Understanding and tuning blue-to-near-infrared photon cutting by the Tm3+/Yb3+ couple.

Lanthanide-based photon-cutting phosphors absorb high-energy photons and 'cut' them into multiple smaller excitation quanta. These quanta are subsequently emitted, resulting in photon-conversion efficiencies exceeding unity. The photon-cutting process relies on energy transfer between optically active lanthanide ions doped in the phosphor. However, it is not always easy to determine, let alone predict, which energy-transfer mechanisms are operative in a particular phosphor. This makes the identification and design of new promising photon-cutting phosphors difficult. Here we unravel the possibility of using the Tm3+/Yb3+ lanthanide couple for photon cutting. We compare the performance of this couple in four different host materials. Cooperative energy transfer from Tm3+ to Yb3+ would enable blue-to-near-infrared conversion with 200% efficiency. However, we identify phonon-assisted cross-relaxation as the dominant Tm3+-to-Yb3+ energy-transfer mechanism in YBO3, YAG, and Y2O3. In NaYF4, in contrast, the low maximum phonon energy renders phonon-assisted cross-relaxation impossible, making the desired cooperative mechanism the dominant energy-transfer pathway. Our work demonstrates that previous claims of high photon-cutting efficiencies obtained with the Tm3+/Yb3+ couple must be interpreted with care. Nevertheless, the Tm3+/Yb3+ couple is potentially promising, but the host material-more specifically, its maximum phonon energy-has a critical effect on the energy-transfer mechanisms and thereby on the photon-cutting performance.

Single Au Atom Doping of Silver Nanoclusters.

Ag29 nanoclusters capped with lipoic acid (LA) can be doped with Au. The doped clusters show enhanced stability and increased luminescence efficiency. We attribute the higher quantum yield to an increase in the rate of radiative decay. With mass spectrometry, the Au-doped clusters were found to consist predominantly of Au1Ag28(LA)123-. The clusters were characterized using X-ray absorption spectroscopy at the Au L3-edge. Both the extended absorption fine structure (EXAFS) and the near edge structure (XANES) in combination with electronic structure calculations confirm that the Au dopant is preferentially located in the center of the cluster. A useful XANES spectrum can be recorded for lower concentrations, or in shorter time, than the more commonly used EXAFS. This makes XANES a valuable tool for structural characterization.

Insights into the Synthesis Mechanism of Ag29 Nanoclusters.

The current understanding of the synthesis mechanisms of noble metal clusters is limited, in particular for Ag clusters. Here, we present a detailed investigation into the synthesis process of atomically monodisperse Ag29 clusters, prepared via reduction of AgNO3 in the presence of dithiolate ligands. Using optical spectroscopy, mass spectrometry, and X-ray spectroscopy, it was determined that the synthesis involves a rapid nucleation and growth to species with up to a few hundred Ag atoms. From these larger species, Ag29 clusters are formed and their concentration increases steadily over time. Oxygen plays an important role in the etching of large particles to Ag29. No other stable Ag cluster species are observed at any point during the synthesis.

Characterisation, degradation and regeneration of luminescent Ag29 clusters in solution.

Luminescent Ag clusters are prepared with lipoic acid (LA) as the ligand. Using a combination of mass spectrometry, optical spectroscopy and analytical ultracentrifugation, the clusters are found to be highly monodisperse with mass 5.6 kDa. We assign the chemical composition [Ag29(LA)12]3- to the clusters, where LA likely binds in a bidentate fashion. The Ag29 clusters show slow degradation, retaining their deep red emission for at least 18 months if stored in the dark. Purification or exposure to light results in faster degradation. No other cluster species are observed during the degradation process. Once degraded, the clusters could easily be regenerated using NaBH4, which is not usually observed for thiolate-capped Ag clusters.

Structure sensitivity of Cu and CuZn catalysts relevant to industrial methanol synthesis.

For decades it has been debated whether the conversion of synthesis gas to methanol over copper catalysts is sensitive or insensitive to the structure of the copper surface. Here we have systematically investigated the effect of the copper particle size in the range where changes in surface structure occur, that is, below 10 nm, for catalysts with and without zinc promotor at industrially relevant conditions for methanol synthesis. Regardless of the presence or absence of a zinc promotor in the form of zinc oxide or zinc silicate, the surface-specific activity decreases significantly for copper particles smaller than 8 nm, thus revealing structure sensitivity. In view of recent theoretical studies we propose that the methanol synthesis reaction takes place at copper surface sites with a unique configuration of atoms such as step-edge sites, which smaller particles cannot accommodate.