Impact dynamics of granular debris flows based on a small-scale physical model.

The peak pressure of a granular debris flow at low Froude conditions can be calculated with knowledge of the stress anisotropy and the bulk density as well as the run-up height at impact. Based on a small-scale physical model, measurements of stress anisotropy and flow density values at impact are presented and applied to existing run-up prediction models, and further compared with back-calculated run-up coefficients from measured maximum impact pressures. For this purpose, we conducted 17 experiments with impact measurements and six experiments without impact measurements at Froude numbers, ranging from 0.84 to 2.41. Our results indicate that run-up heights are best reproduced by predictive models, either based on energy or mass and moment conservation, when anisotropic stress conditions, found in this study to range from 1.2 to 5.0, and bulk density variations due to impact, ranging in this study from 0.8 to 2.3, are considered. The influence of stress anisotropy and density variation on the run-up prediction differs, depending on the modelling approach. For the calculation of run-up heights based on the energy conservation concept, the influence of stress anisotropy becomes more significant with increasing Froude number, whereas for models based on mass and momentum conservation, bulk density variations have a greater influence on the estimation of the potential run-up.

Use of Alkaline-Activated Energy Waste Raw Materials in Geopolymer Concrete.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geopolymer concretes. The compressive strength, water absorption, and bulk density results, along with SEM photos showing the structure of the obtained composite, were obtained. Tests conducted on the specifications of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. A statistical analysis of the experimental data, which investigated the influence of three key variables on the compressive strength, water absorption, and bulk density of lightweight geopolymer concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72%, and a bulk density of 1486.6 kg per cubic meter (kg/m³). These findings underscore the importance of alkali content, curing temperature, and alkali concentration in tailoring the properties of lightweight geopolymer concrete to meet specific performance requirements.

On the detailed mapping of peat (raised bogs) using airborne radiometric data.

This study concerns the applied use of the natural radioactivity in soils. The relevance of airborne radiometric (gamma ray) survey data to peat mapping is now well established and such data have been used in a stand-alone sense and as covariates in machine learning algorithms. Here we present a method to use these data to accurately map the boundaries of peat (raised bogs). This has the potential to assist with the estimation of carbon stocks using a property-based assessment of soil. The significance of such regionally-uniform survey data lies in the subsurface information carried by the measurement which contrasts with the surficial nature of many other covariates. Soils attenuate radiometric flux by virtue of their bulk density (and associated carbon content) and water saturation level. The high attenuation levels in low density, wet peat materials give rise to a distinctive soil response. Here an entirely physics-based assessment of flux attenuation is carried out both theoretically and empirically. Radiometric data from the ongoing Tellus airborne survey of Ireland are used. The study area is characterised by an extensive assemblage of discrete raised peat bogs in a framework of largely mineral soils. Peat is detected by a property contrast with adjacent soils and so we consider all soils within the study area. The relatively low lateral resolution of the airborne data is demonstrated by modelling and we examine the behaviour of a combined spatial derivative of the data. The procedure allows the identification of the edges of the 128 peat polygons considered and indicates other additional potential areas of subsurface peat. The data appear to resolve the differences that exist across three available soil/peat databases that are used for the validation of the results obtained.

Effect of Biostimulant, Manure Stabilizer, and Manure on Soil Physical Properties and Vegetation Status.

Food production sustainability is one of contemporary agriculture's fundamental challenges. Farmers are currently facing high input prices in crop production and declining organic matter in the soil. For this reason, a field experiment was established to assess the effect of the biostimulant NeOsol (NS), the manure stabilizer Z'fix (ZF), farmyard manure (FM), and their combination in farm practice. In situ measurements provided information on the change in bulk density (BD), unit draft (UD), saturated hydraulic conductivity (SHC), and cone index (CI). Furthermore, the vegetation status was investigated via vegetation indices, and the yield and quality parameters were assessed. Management of the experimental field resulted in an overall decrease in BD over time for the treated variants compared to the control (CL). The decrease with time was also verified in the case of UD and CI at the depth zone of 10-20 cm. Variants FM (by 8.0%), FM_NS (by 7.3%), and FM_ZF_NS (by 3.8%) proved to have lower UD values than CL. An overall increase in SHC and in yield was observed over time. Concerning SHC, only FM (by 58.5%) proved different from CL. The yield of all the treated variants, i.e., NS (by 8.2%), FM (by 10.8%), FM_NS (by 14.1%), FM_ZF (by 17.8%), and FM_ZF_NS (by 20.1%), surpassed CL. Simultaneously, none of the examined treatments proved to have any adverse effect either on soil or on plant-related variables.

Dynamics of soil penetration resistance, moisture depletion pattern and crop productivity determined by mechanized cultivation and lifesaving irrigation in zero till blackgram.

Rice fallow black gram is grown under the residual moisture situation as a relay crop in heavy texture montmorillonite clay soil under zero till condition. Since the crop is raised during post monsoon season, the crop often experiences terminal stress due to limited water availability and no rainfall. Surface irrigation in montmorillonite clay soil is determent to pulse crop as inundation causes wilting. Therefore, zero tilled rice fallow black gram has to be supplemented with micro irrigation at flowering stage (35 days after sowing) to alleviate moisture stress and to increase the productivity as well. Hence micro farm pond in a corner of one ha field was created to harvest the rain water during monsoon season and the same was utilized to supplement the crop with lifesaving irrigation through mobile sprinkler at flowering stage for the crop grown under conservation agriculture. Soil cracking is also the common phenomena of montmorillonite clay soil where evaporations losses would be more through crack surfaces. The present study was therefore conducted to study the changes in the soil physical properties, crop establishment and productivity in conjunction with mechanized sowing and harvest and supplemental mobile sprinkler irrigation. Sowing of black gram by broadcasting 10 days prior to the manual harvest of rice, manual drawn single row seed drill after the machine harvest of rice and sowing by broadcasting at 4 days prior to machine harvest of rice was experimented separately and in combination with lifesaving irrigation. Results indicated that the number of wheel passes and lifesaving irrigation had a very strong impact on soil penetration resistance and soil moisture. Combined harvester followed by no till seed drill increased the soil penetration resistance in all the layers (0-5 cm, 5-10 cm and 10-15 cm). Two passes of wheel increased the mean soil penetration resistance from 407 KPa to 502 KPa. The soil penetration resistance (0-5 cm) at harvest shown that black gram sown by manual broadcasting 10 days prior to manual harvest of paddy supplemented with life irrigation on 30 DAS reduced the soil penetration resistance from 690 Kpa to 500 Kpa, 740 Kpa to 600 Kpa and 760 Kpa to 620 Kpa respectively at 0-5 cm, 5-10 cm and 10-15 cm layer. In general, moisture depletion rate was rapid in the surface layer of 0-5 cm as compared to other layers of 5-10 cm and 10-15 cm up to 30 DAS (Flowering stage). The moisture content and the soil penetration resistance had an inverse relationship. The soil penetration resistance also had an inverse relationship with the root length in which the root length lowers as the soil penetration resistance increases. The soil crack measured at 60 DAS was deeper with no till seed drill (width of 3.94 cm and depth of 13.67 cm) which was mainly due to surface layer compaction. The relative water content, specific leaf weight and chlorophyll content were significantly improved through the supplemental irrigation given on 30 DAS irrespective of crop establishment methods. The results further indicated that compaction of ploughed layer in the moist soil due to combined harvester and no till seed drill had a negative impact on yield (457 kg ha-1), which was improved by 19.03 per cent due to increased soil moisture with supplemental irrigation. The mean yield increase across different treatments due to supplemental lifesaving irrigation through mobile sprinkler was 20.4 per cent.

Carbon content and other soil properties of near-surface peats before and after peatland restoration.

Peatland restoration usually aims at restarting the peatlands' function to store carbon within peat. The soil properties of the near-surface peat can give a first understanding of this process. Therefore, we sampled pH value, total organic carbon content (TOC), total nitrogen content (TN), C/N ratio as well as dry bulk density (BD), and describe the structure of near-surface peats in six restored fens in North-East Germany before (2002-2004) and after (2019-2021) restoration. Before restoration, the study sites showed peat degradation to various extents in their near-surface peats. pH values remained relatively stable over time. Comparing the degraded peat horizons, TOC increased significantly in four study sites, ranging from 35.7% to 47.8% in 2002-2004 and from 42.5% to 54.0% in 2019-2021. TN varied from 1.5% to 3.5% in 2002-2004 and from 1.8% to 3.2% in 2019-2021, but changes were only significant in one site, showing a slight decrease. In three sites, the increase in C/N ratio was significant, indicating lower nutrient availability. BD ranged from 0.08 to 0.48 g/cm3 in 2002-2004 and from 0.10 to 0.16 g/cm3 in 2019-2021, decreasing significantly in four sites. The structure of the degraded peat horizons changed after restoration to a more homogenous, sludge mass with larger re-aggregates. In three sites, new peat moss peat layers above the degraded soil horizon were present in 2019-2021, with a mean thickness of 6.8 to 36.1 cm. The structure was comparable to typical, slightly decomposed peat moss peat. Our findings suggest that within about 17 years after fen restoration, and thereby a water table rise close to surface, TOC of the near-surface peats increased to values that are typical for undisturbed peatlands. This indicates that restoration can lead to the re-establishment of peatlands as potential carbon sinks, with TOC within the near-surface peat as one key factor in this process. Further, we assume that the decrease in nutrient availability, decrease of BD, and new, undisturbed peat layers can favor the establishment of mire-specific biodiversity and support ecosystem services similar to near-natural mires.

Dataset of physical properties of histosols topsoils effected by wildfire in Indonesia.

Physical properties of peat are widely applied to detect the quality of peatland ecosystem. A comprehensive dataset on the peat properties is the foundation for the development tool and model of peat ecosystem, especially in region with frequent wildfire. Here we established a tabular dataset for physical properties of lowland tropical peatland in Indonesia. The data were obtained in dry season 2019 and 2023, respectively, at Jambi and Central Kalimantan peatlands. The dataset comprises of 66 peat samples from two land-uses namely secondary forest and ex-burned lowly vegetation. The physical properties are bulk density, porosity, water retention at four pressures (-1, -10, -25, and -1500 kPa), and water holding capacity. In addition, a set parameter of van Genuchten for water retention curve is available. The field-observed dataset provides a solid base for a better understanding of physical peat properties and can be used as a first step to develop peat water retention database in lowland tropical peatlands.

Influence of Cement Kiln Dust on Long-Term Mechanical Behavior and Microstructure of High-Performance Concrete.

Cement production in the world market is steadily increasing. In 2000, it was 1600 million tons, while as of 2013, the annual amount exceeded 4000 million tons. The burning of cement clinker is associated with the generation of waste. It is estimated that the amount of cement kiln dust (CKD), during combustion, reaches about 15-20%, which means 700 million tons per year. However, not all types of by-products are reusable due to high alkali, sulfate, and chloride contents, which can adversely affect the environment. One environmentally friendly solution may be to use CKD in the production of high-performance concrete (HPC), as a substitute for some of the cement. This paper presents a study of the short- and long-term physical and mechanical properties of HPC with 5%, 10%, 15%, and 20% CKD additives. The experiments determined density, water absorption, porosity, splitting tensile strength, compressive strength, modulus of elasticity, ultrasonic pulse velocity, and evaluated the microstructure of the concrete. The addition of CKD up to 10% caused an increase in the 28- and 730-day compressive strengths, while the values decreased slightly when CKD concentration increased to 20%. Splitting tensile strength decreased proportionally with 5-20% amounts of CKD regardless of HPC age. Porosity, absorbability, and ultrasonic pulse velocity decreased with increasing cement dust, while the bulk density increased for HPC with CKD. Microstructure analyses showed a decrease in the content of calcium silicate hydrate (C-S-H), acceleration of setting, and formation of wider microcracks with an increase in CKD. From the results, it was shown that a 15% percentage addition of CKD can effectively replace cement in the production of HPC and contribute to reducing the amount of by-product from the burning of cement clinker.

Pyrolysis kinetics and potential utilization analysis of cereal biomass by-products; an experimental analysis for cleaner energy productions in India.

The optimal utilization of biomass relies heavily on the specific material and individual needs. Cereal biomass by-products can potentially be employed in thermochemical processes such as pyrolysis and gasification. To compare biomass sources, ultimate analysis, biochar potential, proximate analysis, thermal gravimetric analysis, price per megajoule generated heat, surface texture, and availability are used. A global survey of biomass wastes and opportunities for heat generation is presented in the current article. Here, nine different cereal-based agricultural waste products (barley, wheat, millet, oats, rice, rye straw, sorghum straw/stalk, and maize cob) are studied. Cereal wastes are compared based on calorific value, water content, volatile matter, ash content and ash chemical composition, bulk density, charring properties, availability, and transportation. According to the estimate, 156 million metric tonnes per year, or 6% of India's total emissions, could be eliminated by rice husk alone. Wheat straws, on the other hand, can cut emissions by 2%. Additionally, processing these nine feedstocks might result in the production of 40 GW of electrical energy, which would increase the installed capacity of India's national electric grid by 9%.

The importance of accounting method and sampling depth to estimate changes in soil carbon stocks.

BACKGROUND: As interest in the voluntary soil carbon market surges, carbon registries have been developing new soil carbon measurement, reporting, and verification (MRV) protocols. These protocols are inconsistent in their approaches to measuring soil organic carbon (SOC). Two areas of concern include the type of SOC stock accounting method (fixed-depth (FD) vs. equivalent soil mass (ESM)) and sampling depth requirement. Despite evidence that fixed-depth measurements can result in error because of changes in soil bulk density and that sampling to 30 cm neglects a significant portion of the soil profile's SOC stock, most MRV protocols do not specify which sampling method to use and only require sampling to 30 cm. Using data from UC Davis's Century Experiment ("Century") and UW Madison's Wisconsin Integrated Cropping Systems Trial (WICST), we quantify differences in SOC stock changes estimated by FD and ESM over 20 years, investigate how sampling at-depth (> 30 cm) affects SOC stock change estimates, and estimate how crediting outcomes taking an empirical sampling-only crediting approach differ when stocks are calculated using ESM or FD at different depths. RESULTS: We find that FD and ESM estimates of stock change can differ by over 100 percent and that, as expected, much of this difference is associated with changes in bulk density in surface soils (e.g., r = 0.90 for Century maize treatments). This led to substantial differences in crediting outcomes between ESM and FD-based stocks, although many treatments did not receive credits due to declines in SOC stocks over time. While increased variability of soils at depth makes it challenging to accurately quantify stocks across the profile, sampling to 60 cm can capture changes in bulk density, potential SOC redistribution, and a larger proportion of the overall SOC stock. CONCLUSIONS: ESM accounting and sampling to 60 cm (using multiple depth increments) should be considered best practice when quantifying change in SOC stocks in annual, row crop agroecosystems. For carbon markets, the cost of achieving an accurate estimate of SOC stocks that reflect management impacts on soils at-depth should be reflected in the price of carbon credits.

Characterization of different solid fuels from waste for an advanced online fuel control system designed for large-scale incineration plants.

Despite many years of experience in the incineration of solid fuels from waste, the heterogeneity of solid fuels and their varying properties still pose a challenge for a stable and clean combustion in large-scale incineration plants. In modern facilities such as municipal waste incineration plants there still exists a lack of knowledge on the exact amount and calorific value of waste entering onto the grate. Based on the works of Warnecke et al. and Zwiellehner et al., in our project 'AdOnFuelControl', we determined the initial bulk density at the feed hopper by measuring the weight of the waste via the crane weigher and the volume via a high-performance 3D laser scanner. With the help of the determined bulk density, the lower heating value (LHV) and the compression in the feed hopper were calculated. All this information was integrated into the combustion control system, which provided a high potential for an optimized operation of the plant. In this article, six different fuels (fresh and aged municipal solid waste, refuse-derived fuel (fluff), refuse-derived fuel (fine grain), waste wood and dried, grained sewage sludge) were examined for the elemental composition, the LHV, fuel-specific parameters and the compression behaviour. In addition, initial tests with the 3D laser scanner as well as formulas for the calculation of the density in the feed hopper were presented. Based on the results of the experiments, the chosen approach seems very promising for optimized combustion control in large-scale incineration plants. As a next step, the gained knowledge and technology should be integrated in the municipal waste incineration plant.

Temporal and vertical dynamics of carbon accumulation potential under grazing-excluded grasslands in China: The role of soil bulk density.

Despite the progress made in understanding relevant carbon dynamics under grazing exclusion, previous studies have underestimated the role of soil bulk density (BD), and its implications for potential accumulation of soil organic carbon (SOC), especially at regional scale over long term. In this study, we first constructed a database covering a vast majority of the grasslands in northwestern China based on 131 published literatures. A synthesis was then conducted by analyzing the experimental data to comprehensively investigate the mechanisms of vegetation recovery, carbon-nitrogen coupling, and the importance of changed soil BD in evaluating SOC sequestration potential. The results showed that although the recovery of vegetation height and cover were both critical for improving vegetation biomass, vegetation height required a longer recovery period. While the SOC accumulation was found to be greater in surface layers than deeper ones, it exhibited a reduced capacity for carbon sequestration and an increased risk of SOC loss. Grazing exclusion significantly reduced soil BD across different soil profiles, with the rate of change influenced by soil depth, time, geographical and climatic conditions. The potential for SOC accumulation in the top 30 cm of soil based on data of 2003-2022 was 0.78 Mg ha-1 yr-1 without considering BD effects, which was significantly underestimated compared to that of 1.16 Mg ha-1 yr-1 when BD changes were considered properly. This suggests that the efficiency of grazing exclusion in carbon sequestration and climate mitigation may have been previously underreported. Furthermore, mean annual precipitation represented the most relevant environmental factor that positively correlated to SOC accumulation, and a wetter climate may offer greater potential for carbon accumulation. Overall, this study implies grazing exclusion may play an even more critical role in carbon sequestration and climate change mitigation over long-term than previously recognized, which provides essential scientific evidence for implementing stepwise ecological restoration in grasslands.

Practical Guide to Measuring Wetland Carbon Pools and Fluxes.

Wetlands cover a small portion of the world, but have disproportionate influence on global carbon (C) sequestration, carbon dioxide and methane emissions, and aquatic C fluxes. However, the underlying biogeochemical processes that affect wetland C pools and fluxes are complex and dynamic, making measurements of wetland C challenging. Over decades of research, many observational, experimental, and analytical approaches have been developed to understand and quantify pools and fluxes of wetland C. Sampling approaches range in their representation of wetland C from short to long timeframes and local to landscape spatial scales. This review summarizes common and cutting-edge methodological approaches for quantifying wetland C pools and fluxes. We first define each of the major C pools and fluxes and provide rationale for their importance to wetland C dynamics. For each approach, we clarify what component of wetland C is measured and its spatial and temporal representativeness and constraints. We describe practical considerations for each approach, such as where and when an approach is typically used, who can conduct the measurements (expertise, training requirements), and how approaches are conducted, including considerations on equipment complexity and costs. Finally, we review key covariates and ancillary measurements that enhance the interpretation of findings and facilitate model development. The protocols that we describe to measure soil, water, vegetation, and gases are also relevant for related disciplines such as ecology. Improved quality and consistency of data collection and reporting across studies will help reduce global uncertainties and develop management strategies to use wetlands as nature-based climate solutions. Supplementary Information: The online version contains supplementary material available at 10.1007/s13157-023-01722-2.

Preparation and Performance of Ferric-Rich Bauxite-Tailing-Based Thermal Storage Ceramics.

In recent years, regenerative thermal oxidizer (RTO) has been widely used in the petroleum industry, chemical industry, etc. The massive storage required by solid waste has become a serious problem. Due to their chemical composition, bauxite tailings as raw materials for high-temperature thermal storage ceramics show enormous potential in the fields of research and application. In this study, we propose a method for preparing ferric-rich and high specific storage capacity by adding Fe2O3 powder to bauxite tailings. Based on a 7:3 mass ratio of bauxite tailings to lepidolite, Fe2O3 powder with different mass fractions (7 wt%, 15 wt%, 20 wt%, 30 wt%, and 40 wt%) was added to the ceramic material to improve the physical properties and thermal storage capacity of thermal storage ceramics. The results showed that ferric-rich thermal storage ceramics with optimal performance were obtained by holding them at a sintering temperature of 1000 °C for 2 h. When the Fe2O3 content was 15 wt%, the bulk density of the thermal storage ceramic reached 2.53 g/cm3, the compressive strength was 120.81 MPa, and the specific heat capacity was 1.06 J/(g·K). This study has practical guidance significance in the preparation of high thermal storage ceramics at low temperatures and low costs.

Comparison of four synthetic CT generators for brain and prostate MR-only workflow in radiotherapy.

BACKGROUND: The interest in MR-only workflows is growing with the introduction of artificial intelligence in the synthetic CT generators converting MR images into CT images. The aim of this study was to evaluate several commercially available sCT generators for two anatomical localizations. METHODS: Four sCT generators were evaluated: one based on the bulk density method and three based on deep learning methods. The comparison was performed on large patient cohorts (brain: 42 patients and pelvis: 52 patients). It included geometric accuracy with the evaluation of Hounsfield Units (HU) mean error (ME) for several structures like the body, bones and soft tissues. Dose evaluation included metrics like the Dmean ME for bone structures (skull or femoral heads), PTV and soft tissues (brain or bladder or rectum). A 1%/1 mm gamma analysis was also performed. RESULTS: HU ME in the body were similar to those reported in the literature. Dmean ME were smaller than 2% for all structures. Mean gamma pass rate down to 78% were observed for the bulk density method in the brain. Performances of the bulk density generator were generally worse than the artificial intelligence generators for the brain but similar for the pelvis. None of the generators performed best in all the metrics studied. CONCLUSIONS: All four generators can be used in clinical practice to implement a MR-only workflow but the bulk density method clearly performed worst in the brain.

Effects of gravel on the evaluation of soil organic carbon density in Pinus massoniana plantations.

Gravel (>2 mm) is one of the main parameters for estimating soil carbon pool. To assess the effects of gravel on soil bulk density (BD) and organic carbon density (SOCD) in Pinus massoniana plantations, we estimated the BD and SOCD at the 0-10, 10-20 and 20-40 cm soil depths of 131 plots under two different conditions, with and without removing gravel. The BD of each soil layer after removing gravel was 0.58-1.57, 0.60-1.67, and 0.59-1.75 g·cm-3, respectively, which was significantly lower than that before removing gravel. Gravel increased the BD by 6.5%-6.8%. The SOCD of each soil layer before removing gravel was 8.93-65.97, 7.63-59.08, and 8.79-94.53 t·hm-2, respectively, which was higher than that after removing gravel. Overall, by neglecting the effect of gravel, SOCD was overestimated by 4.9%-11.8%. As gravel content increased, the relative deviation in the estimated BD and SOCD among different methods increased. When the gravel content was higher than 20%, the estimated SOCD at soil layer of 0-40 cm showed a significant difference between neglecting gravel and removing gravel, with the former being 29.7%-47.4% higher than the latter. In conclusion, gravel markedly affected the estimations of BD and SOCD. It was recommended that SOCD should be estimated by the method that not only uses the BD after removing gravel but also considers gravel as a correction factor (especially when gravel content is above 20.0%) to avoid overestimation of soil carbon pool.

Modification of Bulk Density, Flow Property and Crystallinity of Microcrystalline Cellulose Prepared from Waste Cotton.

The most affordable type of tablet is the immediately compressible tablet, which uses microcrystalline cellulose (MCC), a popular pharmaceutical excipient, as a filler or binder. To make it compatible with different active drugs and excipients, we tried to change some physical properties of the MCC. In the current study, we used a chelating agent to pretreat the waste cotton before pulping, bleaching, and finally, hydrochloric acid degradation with a concentration of 2N at 100 °C temperature for 20 min to prepare MCC. The prepared MCC was treated with different concentrations of sodium hydroxide at room temperature or at -20 °C followed by precipitation with hydrochloric acid or ethanol with complete washing with distilled water till neutralization. Evaluation of the degree of polymerization (DP) and FT-IR spectrum confirm the identity of the microcrystalline cellulose. The DP was found to be 216. The bulk density of the unmodified MCC was 0.21 while that of modified MCC varied from 0.253 to 0.594. The modified MCC powder showed good flow properties compared to the unmodified MCC as evaluated by the Hausner index, Carr's index and the angle of repose. The scanning electron microscopy (SEM) of the MCC revealed that the rod shape has been changed to an oval shape due to treatment with sodium hydroxide at -20 °C. The X-ray crystallographic (XRD) analysis indicated that the unmodified MCC and standard MCC showed the crystallinity index (CrI) value of 86.82% and 87.63%, respectively, while the value ranges from 80.18% to 60.7% among the modified MCC powder. The differences in properties of the MCC might be due to the variation of rearrangement of the cellulose chain among the MCC particles due to treatment with different concentrations of a base at different temperatures and precipitation environments. This has enabled us to prepare MCC with different properties which might be compatible with different drugs.

Effects of saline water on soil properties and red radish growth in saline soil as a function of co-applying wood chips biochar with chemical fertilizers.

BACKGROUND: Currently, using unconventional water sources in agriculture has become necessary to face overpopulation worldwide. Therefore, a pot experiment was carried out to evaluate the effects of irrigation with saline water in the presence of co-applied wood chips biochar (WCB) with chemical fertilizers on physicochemical properties and nutrient availability as well as growth parameters, and yield of red radish (Raphanus sativus L.) grown in the saline sandy soil. METHODS: The WCB was added to the saline sandy soil at levels of 0 (control), 2.5, and 5% w/w. Then, this soil was cultivated by red radish plants and irrigated with saline water (5 dS m- 1). This experiment was performed in a randomized complete block design with three replicates. RESULTS: Compared with the control treatment, WCB treatments increased significantly soil water holding capacity by 34.8% and 73.2% for levels of 2.5 and 5%, respectively. Soil pH decreased significantly in all WCB treatments. The relative increase in the total available nitrogen over the control was 30.1 and 103.5% for 2.5 and 5% wood chips biochar, respectively. Compared to the control, applying WCB at 2.5% led to an increase in the fresh root weight of red radish plants by 142.7%, while 5% caused a decrease in the fresh root weight of red radish plants by 29.4%. CONCLUSION: Recently, WCB represents an interesting approach to the rehabilitation of saline soils and the management of using saline water sources. It is recommended that combined application of WCB at a level of 2.5% with chemical fertilizers in order to improve red radish growth and nutrient retention in the saline sandy soil which preserves the ecosystem as well as increases productivity leading to the reduction of costs.

Phosphorus deficiency is the main limiting factor for re-vegetation and soil microorganisms in Mu Us Sandy Land, Northwest China.

Long-term drought induced by low rainfall leads to environmental degradation of land in arid and semi-arid regions. In past decades, re-vegetation of degraded sandy soils to prevent soil erosion has been widely employed, including in Mu Us Sandy Land, which suffers from severe soil erosion. However, it remains unclear how re-vegetation affects soil properties and soil microbes after long restoration periods. In this study, typical plots planting Artemisia ordosica and Salix psammophila were selected to investigate the influence of plant types on soil properties; an area of bare sandy land was used as a control. The results show that re-vegetation increased soil organic carbon (C), total nitrogen (N), soil microbial carbon, microbial nitrogen and soil organic acid, while decreasing soil total phosphorous (TP) content significantly, resulting in increased C/P and N/P ratios. Correlation analysis showed that TP was negatively correlated with oxalic acid (OA) and acetic acid (AA), indicating that increased AA and OA content could accelerate the active utilization of phosphorus and induced low TP in soil. Re-vegetation with A. ordosica significantly decreased the microbial diversity of topsoil. The redundancy analysis showed that TP was main index in affecting microbes. These results that lower P content, higher C/P and N/P ratio and influence of TP on microbes suggest that phosphorus is the main limiting factor for re-vegetation and growth of soil microorganisms. In the future, strategies for the development of sustainable ecosystems in regions suffers from severe soil erosion should consider phosphorus supplementation.

Detrimental Effects of Induced Soil Compaction on Morphological Adaptation and Physiological Plasticity of Selected Multipurpose Tree Species.

Soil compaction has become a global problem affecting soil worldwide. With an increased population, more demands for food and wood have resulted in intensive cultivation and increased mechanization of our farmlands and irrigated plantations. The use of heavy machinery results in soil compaction, which affects the entire soil ecosystem. This study was conducted to analyze the impact of compacted soil on germination and initial growth stages of four major agro-forest trees of central Punjab, Pakistan. Morpho-physiological traits of all selected species (Eucalyptus camaldulensis, Albizia lebbeck, Vachellia nilotica, and Zyziphus mauritiana) were measured against soil compaction. Results indicated that the root and shoot length, biomass, root-shoot ratio, diameter at root collar, no. of leaves and branches, leaf area, germination, and survival %, and physiological traits (i.e., photosynthetic rate, transpiration rate, stomatal conductance, internal CO2 concentration, and photosynthetic water use efficiency) were significantly affected by the induced soil compaction. Eucalyptus camaldulensis Dehnh. performed better and exhibited 96% germination percentage under (1.40 mg m-3) compaction level and gradually decreased by 11% with the increase of compaction level (1.80 mg m-3). It shows that the shorter roots developed due to soil compaction decreased water use efficiency, photosynthesis, and whole-plant physiological performance. The findings concluded that judicious use of machinery is highly desired for sustainable and good-quality wood production from farm trees.