Corrosion Behavior of CMT Cladding Layer of AZ91 Magnesium Alloy Subjected to Friction Stir Processing.

Friction stir processing (FSP) was performed on an AZ91 magnesium alloy cladding layer fabricated by a cold metal transfer (CMT) technique. Electrochemical properties and immersion corrosion behavior of the cladding layer before and after FSP in 3.5 wt.% NaCl solution were investigated. After applying the FSP, the corrosion potential and corrosion current density of the cladding layer increased from -1.455 V to -1.397 V and decreased from 4.135 µA/cm2 to 1.275 µA/cm2, respectively. The results of OM and SEM displayed the refinement of grains and the dispersion of ß-Mg17Al12 second phase in the friction stir processed (FSPed) cladding layer and more severe corrosion of the unprocessed sample. The corrosion rate of the FSPed cladding layer was lower, and a more compact corrosion product film was formed on the surface of the FSPed cladding layer. EDS results and XRD patterns showed that the corrosion products was mainly composed of Mg(OH)2. The increase in Al content in the α-Mg matrix, grain refinement, and fragmentation and dispersion of the ß-Mg17Al12 second phase induced by FSP were the main factors that led to the improvement in corrosion resistance of the cladding layer of the AZ91 magnesium alloy fabricated by CMT.

A Compact MIMO Antenna Based on Modal Analysis for 5G Wireless Applications.

This article presents a planar, non-angular, series-fed, dual-element dipole array MIMO antenna operating at 28 GHz with the metasurface-based isolation improvement technique. The initial design is a single-element antenna with a dual dipole array which is series-fed. These dipole elements are non-uniform in shape and distance. This dipole antenna results in end-fire radiation. The dipole antenna excites the J1 mode for its operation. Further, with the view to improve channel capacity, the dipole array expands the antenna to a three-element MIMO antenna. In the MIMO antenna structure, the sum of the J1, J2, and J3 modes is excited, causing resonance at 28 GHz. This article also proposes a metasurface structure with wide stopband characteristics at 28 GHz for isolation improvement. The metasurface is composed of rectangle-shaped structures. The defected ground and metasurface structure combination suppresses the surface wave coupling among the MIMO elements. The proposed antenna results in a bandwidth ranging from 26.7 to 29.6 GHz with isolation improvement greater than 21 dB and a gain of 6.3 dBi. The antenna is validated with the diversity parameters of envelope correlation coefficient, diversity gain, and channel capacity loss.

Use of NaF and FDG PET/CT Scan for the Assessment of Charcot Joint in Charcot-Marie-Tooth Disease: All That Glitters is Gold?

Increasingly Charcot neuroarthropathy (CN) is being recognized in patients with Charcot-Marie-Tooth (CMT) disease. In this report, we describe a case of CN in a CMT patient, adding to the very scarce literature describing this association. We additionally report his unique evaluation with fluorodeoxyglucose (FDG) and sodium fluoride (NaF) positron emission tomography/computed tomography (PET/CT) scanning, the study of which is limited in CN despite its promising role. A 54-year-old known case of CMT, presented with left foot pain, and swelling for 4 months. Weakness and sensory deficits as a result of CMT were evident in both lower and upper limbs. His x-ray was suggestive of CN. Both FDG and NaF PET/CT scanning demonstrated increased tracer uptake in the first tarsometatarsal joint (TMTJ), in keeping with CN. Recognition of the association of CMT with CN is of vital importance as early diagnosis relies on high clinical suspicion. Characterizing risk factors of CN in CMT patients is still under study. Moreover, there is lack of data evaluating the role of PET/CT in CN and specifically in the context of CMT.

Genetic Landscape of SH3TC2 variants in Russian patients with Charcot-Marie-Tooth disease.

Introduction: Charcot-Marie-Tooth disease type 4C (CMT4C) OMIM#601596 stands out as one of the most prevalent forms of recessive motor sensory neuropathy worldwide. This disorder results from biallelic pathogenic variants in the SH3TC2 gene. Methods: Within a cohort comprising 700 unrelated Russian patients diagnosed with Charcot-Marie-Tooth disease, we conducted a gene panel analysis encompassing 21 genes associated with hereditary neuropathies. Among the cohort, 394 individuals exhibited demyelinating motor and sensory neuropathy. Results and discussion: Notably, 10 cases of CMT4C were identified within this cohort. The prevalence of CMT4C among Russian demyelinating CMT patients lacking the PMP22 duplication is estimated at 2.5%, significantly differing from observations in European populations. In total, 4 novel and 9 previously reported variants in the SH3TC2 gene were identified. No accumulation of a major variant was detected. Three previously reported variants, c.2860C>T p. (Arg954*), p. (Arg658Cys) and c.279G>A p. (Lys93Lys), recurrently detected in unrelated families. Nucleotide alteration p. (Arg954*) is present in most of our patients (30%).

TRPV4 neuromuscular disease registry highlights bulbar, skeletal and proximal limb manifestations.

Dominant missense mutations of the calcium-permeable cation channel TRPV4 cause Charcot-Marie-Tooth disease (CMT) type 2C and two forms of distal spinal muscular atrophy. These conditions are collectively referred to as TRPV4-related neuromuscular disease and share features of motor greater than sensory dysfunction and frequent vocal fold weakness. Pathogenic variants lead to gain of ion channel function that can be rescued by TRPV4 antagonists in cellular and animal models. As small molecule TRPV4 antagonists have proven safe in trials for other disease indications, channel inhibition is a promising therapeutic strategy for TRPV4 patients. However, the current knowledge of the clinical features and natural history of TRPV4-related neuromuscular disease is insufficient to enable rational clinical trial design. To address these issues, we developed a TRPV4 patient database and administered a TRPV4-specific patient questionnaire. Here, we report demographic and clinical information, including CMT examination scores (CMTES), from 68 patients with known pathogenic TRPV4 variants, 40 of whom also completed the TRPV4 patient questionnaire. TRPV4 patients showed a bimodal age of onset, with the largest peak occurring in the first 2 years of life. Compared to CMT1A patients, TRPV4 patients showed distinct symptoms and signs, manifesting more ambulatory difficulties and more frequent involvement of proximal arm and leg muscles. Although patients reported fewer sensory symptoms, sensory dysfunction was often detected clinically. Many patients were affected by vocal fold weakness (55%) and shortness of breath (55%), and 11% required ventilatory support. Skeletal abnormalities were common, including scoliosis (64%), arthrogryposis (33%), and foot deformities. Strikingly, patients with infantile onset of disease showed less sensory involvement and less progression of symptoms. These results highlight distinctive clinical features in TRPV4 patients, including motor-predominant disease, proximal arm and leg weakness, severe ambulatory difficulties, vocal fold weakness, respiratory dysfunction, and skeletal involvement. In addition, patients with infantile onset of disease appeared to have a distinct phenotype with less apparent disease progression based on CMTES. These collective observations indicate that clinical trial design for TRPV4-related neuromuscular disease should include outcome measures that reliably capture non-length dependent motor dysfunction, vocal fold weakness, and respiratory disease.

Compound Heterozygous Mutations of SACS in a Korean Cohort Study of Charcot-Marie-Tooth Disease Concurrent Cerebellar Ataxia and Spasticity.

Mutations in the SACS gene are associated with autosomal recessive spastic ataxia of Charlevoix-Saguenay disease (ARSACS) or complex clinical phenotypes of Charcot-Marie-Tooth disease (CMT). This study aimed to identify SACS mutations in a Korean CMT cohort with cerebellar ataxia and spasticity by whole exome sequencing (WES). As a result, eight pathogenic SACS mutations in four families were identified as the underlying causes of these complex phenotypes. The prevalence of CMT families with SACS mutations was determined to be 0.3%. All the patients showed sensory, motor, and gait disturbances with increased deep tendon reflexes. Lower limb magnetic resonance imaging (MRI) was performed in four patients and all had fatty replacements. Of note, they all had similar fatty infiltrations between the proximal and distal lower limb muscles, different from the neuromuscular imaging feature in most CMT patients without SACS mutations who had distal dominant fatty involvement. Therefore, these findings were considered a characteristic feature in CMT patients with SACS mutations. Although further studies with more cases are needed, our results highlight lower extremity MRI findings in CMT patients with SACS mutations and broaden the clinical spectrum. We suggest screening for SACS in recessive CMT patients with complex phenotypes of ataxia and spasticity.

AGR2-mediated unconventional secretion of 14-3-3ε and α-actinin-4, responsive to ER stress and autophagy, drives chemotaxis in canine mammary tumor cells.

BACKGROUND: Canine mammary tumors (CMTs) in intact female dogs provide a natural model for investigating metastatic human cancers. Our prior research identified elevated expression of Anterior Gradient 2 (AGR2), a protein disulfide isomerase (PDI) primarily found in the endoplasmic reticulum (ER), in CMT tissues, highly associated with CMT progression. We further demonstrated that increased AGR2 expression actively influences the extracellular microenvironment, promoting chemotaxis in CMT cells. Unraveling the underlying mechanisms is crucial for assessing the potential of therapeutically targeting AGR2 as a strategy to inhibit a pro-metastatic microenvironment and impede tumor metastasis. METHODS: To identify the AGR2-modulated secretome, we employed proteomics analysis of the conditioned media (CM) from two CMT cell lines ectopically expressing AGR2, compared with corresponding vector-expressing controls. AGR2-regulated release of 14-3-3ε (gene: YWHAE) and α-actinin 4 (gene: ACTN4) was validated through ectopic expression, knockdown, and knockout of the AGR2 gene in CMT cells. Extracellular vesicles derived from CMT cells were isolated using either differential ultracentrifugation or size exclusion chromatography. The roles of 14-3-3ε and α-actinin 4 in the chemotaxis driven by the AGR2-modulated CM were investigated through gene knockdown, antibody-mediated interference, and recombinant protein supplement. Furthermore, the clinical relevance of the release of 14-3-3ε and α-actinin 4 was assessed using CMT tissue-immersed saline and sera from CMT-afflicted dogs. RESULTS: Proteomics analysis of the AGR2-modulated secretome revealed increased abundance in 14-3-3ε and α-actinin 4. Ectopic expression of AGR2 significantly increased the release of 14-3-3ε and α-actinin 4 in the CM. Conversely, knockdown or knockout of AGR2 expression remarkably reduced their release. Silencing 14-3-3ε or α-actinin 4 expression diminished the chemotaxis driven by AGR2-modulated CM. Furthermore, AGR2 controls the release of 14-3-3ε and α-actinin 4 primarily via non-vesicular routes, responding to the endoplasmic reticulum (ER) stress and autophagy activation. Knockout of AGR2 resulted in increased α-actinin 4 accumulation and impaired 14-3-3ε translocation in autophagosomes. Depletion of extracellular 14-3-3ε or α-actinin 4 reduced the chemotaxis driven by AGR2-modulated CM, whereas supplement with recombinant 14-3-3ε in the CM enhanced the CM-driven chemotaxis. Notably, elevated levels of 14-3-3ε or α-actinin 4 were observed in CMT tissue-immersed saline compared with paired non-tumor samples and in the sera of CMT dogs compared with healthy dogs. CONCLUSION: This study elucidates AGR2's pivotal role in orchestrating unconventional secretion of 14-3-3ε and α-actinin 4 from CMT cells, thereby contributing to paracrine-mediated chemotaxis. The insight into the intricate interplay between AGR2-involved ER stress, autophagy, and unconventional secretion provides a foundation for refining strategies aimed at impeding metastasis in both canine mammary tumors and potentially human cancers.

Genotype-phenotype correlations of AR-CMT2S in a cohort of axonal Charcot-Marie-Tooth patients from Central South China.

BACKGROUND AND AIMS: This study aimed to report nine Charcot-Marie-Tooth disease (CMT) families with six novel IGHMBP2 mutations in our CMT2 cohort and to summarize the genetic and clinical features of all AR-CMT2S patients reported worldwide. METHODS: General information, clinical and neurophysiological data of 275 axonal CMT families were collected. Genetic screening was performed by inherited peripheral neuropathy related genes panel or whole exome sequencing. The published papers reporting AR-CMT2S from 2014 to 2023 were searched in Pubmed and Wanfang databases. RESULTS: In our CMT2 cohort, we detected 17 AR-CMT2S families carrying IGHMBP2 mutations and eight were published previously. Among these, c.743 T > A (p.Val248Glu), c.884A > G (p.Asp295Gly), c.1256C > A (p.Ser419*), c.2598_2599delGA (p.Lys868Sfs*16), c.1694_1696delATG (p.Asp565del) and c.2509A > T (p.Arg837*) were firstly reported. These patients prominently presented with early-onset typical axonal neuropathy and without respiratory dysfunction. So far, 56 AR-CMT2S patients and 57 different mutations coming from 43 families have been reported in the world. Twenty-nine of 32 missense mutations were clustered in helicase domain and ATPase region. The age at onset ranged from 0.11to 20 years (Mean ± SD: 3.43 ± 3.88 years) and the majority was infantile-onset (<2 years). The initial symptoms included weakness of limbs (19, 29.7%), delayed milestones (12, 18.8%), gait disturbance (11, 17.2%), feet deformity (8, 12.5%), feet drop (8, 12.5%), etc. INTERPRETATION: AR-CMT2S accounted for 6.2% in our CMT2 cohort. We firstly reported six novel IGHMBP2 mutations which expanded the genotypic spectrum of AR-CMT2S. Furthermore, 17 AR-CMT2S families could provide more resources for natural history study, drug research and development.

Investigating the Forming Characteristics of 316 Stainless Steel Fabricated through Cold Metal Transfer (CMT) Wire and Arc Additive Manufacturing.

Wire and arc additive manufacturing (WAAM), recognized for its capability to fabricate large-scale, complex parts, stands out due to its significant deposition rates and cost-effectiveness, positioning it as a forward-looking manufacturing method. In this research, we employed two welding currents to produce samples of 316 austenitic stainless steel utilizing the Cold Metal Transfer wire arc additive manufacturing process (CMT-WAAM). This study initially evaluated the maximum allowable arc travel speed (MAWFS) and the formation characteristics of the deposition bead, considering deposition currents that vary between 100 A and175 A in both CMT and CMT pulse(CMT+P) modes. Thereafter, the effect of the CMT+P mode arc on the microstructure evolution was analyzed using the EBSD technique. The findings indicate that the arc travel speed and deposition current significantly affect the deposition bead's dimensions. Specifically, an increase in travel speed or a reduction in current results in reduced bead width and height. Moreover, the employment of the CMT+P arc mode led to a reduction in the average grain size in the mid-section of the sample fabricated by CMT arc and wire additive manufacturing, from 13.426 µm to 9.429 µm. Therefore, the components of 316 stainless steel produced through the CMT+P-WAAM method are considered fit for industrial applications.

AZ91 Magnesium Alloy CMT Cladding Layer Processed Using Friction Stir Processing: Effect of Traverse Speed on Microstructure and Mechanical Properties.

Friction stir processing (FSP) is a solid-state treating method to enhance the mechanical properties of materials by altering their microstructure. In this study, FSP was applied to the AZ91 magnesium alloy cladding layer prepared using cold metal transition (CMT) technology, and the purpose was to investigate the effect of the traverse speed of the H13 steel stirring head under a constant rotation speed on the microstructure and mechanical properties of the cladding layer. The results demonstrated that FSP could effectively decrease the grain size of the cladding layer and lead to the dispersion and dissolution of the coarse ß-Mg17Al12 second phase into the α-Mg matrix. The mechanical characteristics of the processed cladding layer were significantly enhanced compared to the unprocessed cladding layer due to the grain refinement and second-phase strengthening induced by FSP. When the stirring head rotation speed was set at 300 r/min, the average microhardness and tensile properties of the specimens showed a tendency of initially increasing and then dropping as the traverse speed increased. The cladding layer, obtained at a traverse speed of 60 mm/min, displayed optimal mechanical properties with an average microhardness, tensile strength, and elongation of 85.6 HV0.1, 278.5 MPa, and 13.4%, respectively.

PMP22 duplication dysregulates lipid homeostasis and plasma membrane organization in developing human Schwann cells.

Charcot-Marie-Tooth disease type 1A (CMT1A) is the most common inherited peripheral neuropathy caused by a 1.5 megabase tandem duplication of chromosome 17 harboring the PMP22 gene. This dose-dependent overexpression of PMP22 results in disrupted Schwann cell myelination of peripheral nerves. To get better insights into the underlying pathogenic mechanisms in CMT1A, we investigated the role of PMP22 duplication on cellular homeostasis in CMT1A mouse models and in patient-derived induced pluripotent stem cells differentiated into Schwann cell precursors (iPSC-SCPs). We performed lipidomic profiling and bulk RNA sequencing on sciatic nerves of two developing CMT1A mouse models and on CMT1A patient derived iPSC-SCPs. For the sciatic nerves of the CMT1A mice, cholesterol and lipid metabolism was dose-dependently downregulated throughout development. For the CMT1A iPSC-SCPs, transcriptional analysis unveiled a strong suppression of genes related to autophagy and lipid metabolism. Gene ontology enrichment analysis identified disturbances in pathways related to plasma membrane components and cell receptor signaling. Lipidomic analysis confirmed the severe dysregulation in plasma membrane lipids, particularly sphingolipids, in CMT1A iPSC-SCPs. Furthermore, we identified reduced lipid raft dynamics, disturbed plasma membrane fluidity, and impaired cholesterol incorporation and storage, all of which could result from altered lipid storage homeostasis in the patient-derived CMT1A iPSC-SCPs. Importantly, this phenotype could be rescued by stimulating autophagy and lipolysis. We conclude that PMP22 duplication disturbs intracellular lipid storage and leads to a more disordered plasma membrane due to an alteration in the lipid composition, which ultimately may lead to impaired axo-glial interactions. Moreover, targeting lipid handling and metabolism could hold promise for the treatment of CMT1A patients.

Distal hereditary motor neuropathies.

Distal hereditary motor neuropathies (dHMN) are a group of heterogeneous hereditary disorders characterized by a slowly progressive distal pure motor neuropathy. Electrophysiology, with normal motor and sensory conduction velocities, can suggest the diagnosis of dHMN and guide the genetic study. More than thirty genes are currently associated with HMNs, but around 60 to 70% of cases of dHMN remain uncharacterized genetically. Recent cohort studies showed that HSPB1, GARS, BICB2 and DNAJB2 are among the most frequent dHMN genes and that the prevalence of the disease was calculated as 2.14 and 2.3 per 100,000. The determination of the different genes involved in dHMNs made it possible to observe a genotypic overlap with some other neurogenetic disorders and other hereditary neuropathies such as CMT2, mainly with the HSPB1, HSPB8, BICD2 and TRPV4 genes of AD-inherited transmission and recently observed with SORD gene of AR transmission which seems relatively frequent and potentially curable. Distal hereditary motor neuropathy that predominates in the upper limbs is linked mainly to three genes: GARS, BSCL2 and REEP1, whereas dHMN with vocal cord palsy is associated with SLC5A7, DCTN1 and TRPV4 genes. Among the rare AR forms of dHMN like IGHMBP2 and DNAJB2, the SIGMAR1 gene mutations as well as VRK1 variants are associated with a motor neuropathy phenotype often associated with upper motoneuron involvement. The differential diagnosis of these latter arises with juvenile forms of amyotrophic lateral sclerosis, that could be caused also by variations of these genes, as well as hereditary spastic paraplegia. A differential diagnosis of dHMN related to Brown Vialetto Van Laere syndrome due to riboflavin transporter deficiency is important to consider because of the therapeutic possibility.

A study concept of expeditious clinical enrollment for genetic modifier studies in Charcot-Marie-Tooth neuropathy 1A.

BACKGROUND: Caused by duplications of the gene encoding peripheral myelin protein 22 (PMP22), Charcot-Marie-Tooth disease type 1A (CMT1A) is the most common hereditary neuropathy. Despite this shared genetic origin, there is considerable variability in clinical severity. It is hypothesized that genetic modifiers contribute to this heterogeneity, the identification of which may reveal novel therapeutic targets. In this study, we present a comprehensive analysis of clinical examination results from 1564 CMT1A patients sourced from a prospective natural history study conducted by the RDCRN-INC (Inherited Neuropathy Consortium). Our primary objective is to delineate extreme phenotype profiles (mild and severe) within this patient cohort, thereby enhancing our ability to detect genetic modifiers with large effects. METHODS: We have conducted large-scale statistical analyses of the RDCRN-INC database to characterize CMT1A severity across multiple metrics. RESULTS: We defined patients below the 10th (mild) and above the 90th (severe) percentiles of age-normalized disease severity based on the CMT Examination Score V2 and foot dorsiflexion strength (MRC scale). Based on extreme phenotype categories, we defined a statistically justified recruitment strategy, which we propose to use in future modifier studies. INTERPRETATION: Leveraging whole genome sequencing with base pair resolution, a future genetic modifier evaluation will include single nucleotide association, gene burden tests, and structural variant analysis. The present work not only provides insight into the severity and course of CMT1A, but also elucidates the statistical foundation and practical considerations for a cost-efficient and straightforward patient enrollment strategy that we intend to conduct on additional patients recruited globally.

DNA methylation remodeling and the functional implication during male gametogenesis in rice.

BACKGROUND: Epigenetic marks are reprogrammed during sexual reproduction. In flowering plants, DNA methylation is only partially remodeled in the gametes and the zygote. However, the timing and functional significance of the remodeling during plant gametogenesis remain obscure. RESULTS: Here we show that DNA methylation remodeling starts after male meiosis in rice, with non-CG methylation, particularly at CHG sites, being first enhanced in the microspore and subsequently decreased in sperm. Functional analysis of rice CHG methyltransferase genes CMT3a and CMT3b indicates that CMT3a functions as the major CHG methyltransferase in rice meiocyte, while CMT3b is responsible for the increase of CHG methylation in microspore. The function of the two histone demethylases JMJ706 and JMJ707 that remove H3K9me2 may contribute to the decreased CHG methylation in sperm. During male gametogenesis CMT3a mainly silences TE and TE-related genes while CMT3b is required for repression of genes encoding factors involved in transcriptional and translational activities. In addition, CMT3b functions to repress zygotic gene expression in egg and participates in establishing the zygotic epigenome upon fertilization. CONCLUSION: Collectively, the results indicate that DNA methylation is dynamically remodeled during male gametogenesis, distinguish the function of CMT3a and CMT3b in sex cells, and underpin the functional significance of DNA methylation remodeling during rice reproduction.

Three-Dimensional Cultivation a Valuable Tool for Modelling Canine Mammary Gland Tumour Behaviour In Vitro.

Cell cultivation has been one of the most popular methods in research for decades. Currently, scientists routinely use two-dimensional (2D) and three-dimensional (3D) cell cultures of commercially available cell lines and primary cultures to study cellular behaviour, responses to stimuli, and interactions with their environment in a controlled laboratory setting. In recent years, 3D cultivation has gained more attention in modern biomedical research, mainly due to its numerous advantages compared to 2D cultures. One of the main goals where 3D culture models are used is the investigation of tumour diseases, in both animals and humans. The ability to simulate the tumour microenvironment and design 3D masses allows us to monitor all the processes that take place in tumour tissue created not only from cell lines but directly from the patient's tumour cells. One of the tumour types for which 3D culture methods are often used in research is the canine mammary gland tumour (CMT). The clinically similar profile of the CMT and breast tumours in humans makes the CMT a suitable model for studying the issue not only in animals but also in women.

Boosting BDNF in muscle rescues impaired axonal transport in a mouse model of DI-CMTC peripheral neuropathy.

Charcot-Marie-Tooth disease (CMT) is a genetic peripheral neuropathy caused by mutations in many functionally diverse genes. The aminoacyl-tRNA synthetase (ARS) enzymes, which transfer amino acids to partner tRNAs for protein synthesis, represent the largest protein family genetically linked to CMT aetiology, suggesting pathomechanistic commonalities. Dominant intermediate CMT type C (DI-CMTC) is caused by YARS1 mutations driving a toxic gain-of-function in the encoded tyrosyl-tRNA synthetase (TyrRS), which is mediated by exposure of consensus neomorphic surfaces through conformational changes of the mutant protein. In this study, we first showed that human DI-CMTC-causing TyrRSE196K mis-interacts with the extracellular domain of the BDNF receptor TrkB, an aberrant association we have previously characterised for several mutant glycyl-tRNA synthetases linked to CMT type 2D (CMT2D). We then performed temporal neuromuscular assessments of YarsE196K mice modelling DI-CMT. We determined that YarsE196K homozygotes display a selective, age-dependent impairment in in vivo axonal transport of neurotrophin-containing signalling endosomes, phenocopying CMT2D mice. This impairment is replicated by injection of recombinant TyrRSE196K, but not TyrRSWT, into muscles of wild-type mice. Augmenting BDNF in DI-CMTC muscles, through injection of recombinant protein or muscle-specific gene therapy, resulted in complete axonal transport correction. Therefore, this work identifies a non-cell autonomous pathomechanism common to ARS-related neuropathies, and highlights the potential of boosting BDNF levels in muscles as a therapeutic strategy.

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties.

The titanium alloy components utilized in the aviation field are typically large in size and possess complex structures. By utilizing multiple additive manufacturing processes, the precision and efficiency requirements of production can be met. We investigated the hybrid additive manufacturing of Ti-6Al-4V using a combination of cold metal transfer additive manufacturing (CMTAM) and laser metal deposition (LMD), as well as the feasibility of using the CMT-LMD hybrid additive manufacturing process for fabricating Ti-6Al-4V components. Microstructural examinations, tensile testing coupled with digital image correlation and dynamic compressive experiments (by the split Hopkinson pressure bar (SHPB) system) were employed to assess the parts. The results indicate that the interface of the LMD and CMTAM zone formed a compact metallurgical bonding. In the CMTAM and LMD zone, the prior-ß grains exhibit epitaxial growth, forming columnar prior-ß grains. Due to laser remelting, the CMT-LMD hybrid additive zone experiences grain refinement, resulting in equiaxed prior-ß grains at the interface with an average grain size smaller than that of the CMTAM and LMD regions. The microstructures reveal significant differences in grain orientation and morphology among the zones, with distinct textures forming in each zone. In the CMT-LMD hybrid zone, due to interfacial strengthening, strain concentration occurs in the arc additive zone during tensile testing, leading to fracture on the CMTAM zone. Under high-strain-rate dynamic impact conditions, the LMD region exhibits ductile fracture, while the CMTAM zone demonstrates brittle fracture. The hybrid zone combines ductile and brittle fracture modes, and the CMT-LMD hybrid material exhibits superior dynamic impact performance compared to the single deposition zone.

Boosting BDNF in muscle rescues impaired axonal transport in a mouse model of DI-CMTC peripheral neuropathy.

Charcot-Marie-Tooth disease (CMT) is a genetic peripheral neuropathy caused by mutations in many functionally diverse genes. The aminoacyl-tRNA synthetase (ARS) enzymes, which transfer amino acids to partner tRNAs for protein synthesis, represent the largest protein family genetically linked to CMT aetiology, suggesting pathomechanistic commonalities. Dominant intermediate CMT type C (DI-CMTC) is caused by YARS1 mutations driving a toxic gain-of-function in the encoded tyrosyl-tRNA synthetase (TyrRS), which is mediated by exposure of consensus neomorphic surfaces through conformational changes of the mutant protein. In this study, we first showed that human DI-CMTC-causing TyrRSE196K mis-interacts with the extracellular domain of the BDNF receptor TrkB, an aberrant association we have previously characterised for several mutant glycyl-tRNA synthetases linked to CMT type 2D (CMT2D). We then performed temporal neuromuscular assessments of YarsE196K mice modelling DI-CMT. We determined that YarsE196K homozygotes display a selective, age-dependent impairment in in vivo axonal transport of neurotrophin-containing signalling endosomes, phenocopying CMT2D mice. This impairment is replicated by injection of recombinant TyrRSE196K, but not TyrRSWT, into muscles of wild-type mice. Augmenting BDNF in DI-CMTC muscles, through injection of recombinant protein or muscle-specific gene therapy, resulted in complete axonal transport correction. Therefore, this work identifies a non-cell autonomous pathomechanism common to ARS-related neuropathies, and highlights the potential of boosting BDNF levels in muscles as a therapeutic strategy.

The Hexokinase 1 5'-UTR Mutation in Charcot-Marie-Tooth 4G Disease Alters Hexokinase 1 Binding to Voltage-Dependent Anion Channel-1 and Leads to Dysfunctional Mitochondrial Calcium Buffering.

Demyelinating Charcot-Marie-Tooth 4G (CMT4G) results from a recessive mutation in the 5'UTR region of the Hexokinase 1 (HK1) gene. HK participates in mitochondrial calcium homeostasis by binding to the Voltage-Dependent Anion Channel (VDAC), through its N-terminal porin-binding domain. Our hypothesis is that CMT4G mutation results in a broken interaction between mutant HK1 and VDAC, disturbing mitochondrial calcium homeostasis. We studied a cohort of 25 CMT4G patients recruited in the French gypsy population. The disease was characterized by a childhood onset, an intermediate demyelinating pattern, and a significant phenotype leading to becoming wheelchair-bound by the fifth decade of life. Co-IP and PLA studies indicated a strong decreased interaction between VDAC and HK1 in the patients' PBMCs and sural nerve. We observed that either wild-type HK1 expression or a peptide comprising the 15 aa of the N-terminal wild-type HK1 administration decreased mitochondrial calcium release in HEK293 cells. However, mutated CMT4G HK1 or the 15 aa of the mutated HK1 was unable to block mitochondrial calcium release. Taken together, these data show that the CMT4G-induced modification of the HK1 N-terminus disrupts HK1-VDAC interaction. This alters mitochondrial calcium buffering that has been shown to be critical for myelin sheath maintenance.