RESUMO
The aim of this study was to explore the thermal properties of epoxy-acrylate blends for the liquid crystal display (LCD) 3D printing technique. Starting from an epoxy-acrylate blend with a ratio of epoxy to acrylate of 50:50, the effect of adding a reactive monofunctional epoxy diluent was evaluated. The diluent was a resin composed by oxirane, mono[(C12-14 alkyl) methyl] derivatives selected for its low viscosity (i.e., 1.8 Poise) at room temperature and its reactivity. The diluent content varied from 15 to 25 wt% and, for all the formulation, double curing cycles, where thermal curing followed photocuring, were studied. The effect of different curing temperatures was also evaluated. The control of the diluent content and of the curing temperature allowed tailoring of the thermomechanical resin properties while improving the resin's processability. The glass transition ranged from 115.4 °C to 90.8 °C depending on the combination of diluent content and post-curing temperature. The resin developed displayed a faster processing time tested on a reference part with printing time of 4 h and 20 min that was much lower than the printing times (7 and 16 h) observed for the starting formulations.
RESUMO
In this work, a highly branched polyurea (HBP-NH2) similar to urea structure was introduced to phenol-formaldehyde (PF) resin to accelerate itscuring speed The results of gel time and bonding strength were combined to obtain a good modified additional stage and amount of HBP-NH2. The relative molar mass changes of HBP-NH2-modified PF resin were investigated by gel permeation chromatography (GPC). The effects of HBP-NH2 on the curing of PF resin were investigated by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The effect of HBP-NH2 on the structure of PF resin was also investigated by nuclear magnetic resonance carbon spectroscopy (13C-NMR). The test results show that the gel time of the modified PF resin was reduced by 32% and 51% at 110 °C and 130 °C, respectively. Meanwhile, the addition of HBP-NH2 increased the relative molar mass of PF resin. The bonding strength test showed that the bonding strength of modified PF resin increased by 22% after soaking in boiling water (93 °C ± 2) for 3 h. The DSC and DMA analysis indicated that the curing peak temperature decreased from 137 °C to 102 °C, and the curing rate of the modified PF resin was also faster than that of the pure PF resin. The 13C-NMR results showed that HBP-NH2 in the PF resin reacted to produce a co-condensation structure. Finally, the possible reaction mechanism of HBP-NH2 for the modification of PF resin was given.
RESUMO
Abstract The aim in this study was to evaluate the influence of different ratio of camphorquinone/tertiary amine concentration on the flexural strength (FS), elastic modulus (EM), degree of conversion (DC), yellowing (YL), water sorption (WS) and water solubility (WSL) of experimental composites. Thus, acrylate blends were prepared with different camphorquinone (CQ) and amine (DABE) concentrations and ratios by weight: (CQ/DABE%): 0.4/0.4% (C1), 0.4/0.8% (C2), 0.6/0.6% (C3), 0.6/1.2% (C4), 0.8/0.8% (C5), 0.8/1.6% (C6), 1.0/1.0% (C7), 1.0/2.0% (C8), 1.5/1.5% (C9), 1.5/3.0% (C10). For the FS and EM, rectangular specimens (7x2x1 mm, n=10) were photo-activated by single-peak LED for 20 s and tested at Instron (0.5 mm/min). Then, the same specimens were evaluated by FTIR for DC measurement. For YL, disks (5x2 mm, n=10) were prepared, light-cured for 20 s and evaluated in spectrophotometer using the b aspect of the CIEL*a*b* system. For WS and WSL, the volume of the samples was calculated (mm³). For WS and WSL, composites disks (5x0.5 mm, n=5) were prepared. After desiccation, the specimens were stored in distilled water for 7 days and again desiccated, in order to measure the WS and WSL. Data were submitted to one-way ANOVA and Tukey's test (5%). The groups C8, C9 and C10 showed higher DC, EM and YL means, compared to other composites. Therefore, the FS and WS values were similar among all groups. Also, C1, C2 and C3 presented higher WSL in 7 days, compared to other composites. In general, higher concentrations of camphorquinone promoted higher physical-mechanical properties; however, inducing higher yellowing effect for the experimental composites
Resumo O objetivo foi avaliar a influência da concentração e proporção de canforoquinona (CQ)/amina terciária (DABE) na resistência à flexão (RF), módulo flexural (MF), grau de conversão (GC), amarelamento (AM), sorpção (SA) e solubilidade em água (SL) de compósitos experimentais. Blendas acrilatas foram preparadas com diferentes concentrações e proporções de CQ/DABE em peso, como segue: (CQ/DABE%): 0,4/0,4% (C1); 0,4/0,8% (C2); 0,6/0,6% (C3); 0,6/1,2% (C4); 0,8/0,8% (C5); 0,8/1,6% (C6); 1,0/1,0% (C7); 1,0/2,0% (C8); 1,5/1,5% (C9); 1,5/3,0% (C10). Para RF e MF, espécimes retangulares (7x2x1 mm, n=10) foram fotoativados com LED de pico único (Radii Cal) por 20 s e testados em máquina Instron (0,5 mm/min). Após, o GC dos mesmos espécimes (fragmentos) foi mensurado por FTIR. Para AM, discos de compósito (5x2 mm, n=10) foram preparados, fotoativados por 20 s e imediatamente avaliados em espectrofotômetro, considerando o aspecto b do sistema CIEL*a*b*. Para SA e SL, discos de compósito (5x0,5 mm, n=5) foram preparados e seus volumes calculados (mm³). Após desidratação, as amostras foram pesadas e armazenadas em água destilada por 7 dias, pesadas e novamente desidratadas e pesadas, para se calcular o SA e SL. Os dados foram submetidos a one-way ANOVA e teste de Tukey (5%). Os grupos C8, C9 e C10 mostraram maior GC, MF e AM, comparado aos outros grupos. No entanto, RF e SA foram similares entre todos os grupos. Ainda, C1, C2 e C3 apresentaram maior SL em 7 dias comparado aos outros grupos. Em geral, maiores concentrações de CQ promoveram melhores propriedades físico-mecânicas; no entanto, levaram ao maior amarelamento dos compósitos.
