Hydrodynamic frictional performance of fouled panels: a comparative study of different coating types.

This research study delves into the hydrodynamic frictional characteristics of fouled panels coated with different types of coatings, investigating how fouling coverage and surface roughness influence drag. The investigation incorporates data on the overall percentage coverage of fouling, as well as roughness measurements obtained through a 3D profilometer. Drag data collected from a flowcell simulation of real-world flow conditions complements these measurements. Notably, the determination of the level of fouling leverages the capabilities of CIE L*a*b as an image analysis method, focusing on the overall coverage rather than individual fouling species. The objective is to illustrate how fouled panels perform under varying flow and coating conditions compared to their clean counterparts. Furthermore, the paper proposes a roughness scaling approach that considers both the percentage coverage and measured areal roughness for each coating type, encompassing both fouled and unfouled areas. This approach provides valuable insights into the combined effects of fouling and surface roughness on hydrodynamic performance, enhancing our understanding of the intricate interplay between these factors.

Sustainable control of microplastics in wastewater using the electrochemically enhanced living membrane bioreactor.

Wastewater treatment plant (WWTP) discharges are major contributors to the release of microplastics (MPs) into the environment. This research work aimed to assess the performance of the novel living membrane bioreactor (LMBR), which utilizes a biological layer as a membrane filter for the removal of polyethylene (PE) MPs from wastewater. The impact of an intermittently applied low current density (0.5 mA/cm2) on the reduction of MPs in the electrochemically enhanced LMBR (e-LMBR) has also been examined. The reactors were also compared to a conventional membrane bioreactor (MBR) and an electro-MBR (e-MBR). 1H nuclear magnetic resonance spectroscopy (1H NMR) was implemented for the MPs detection and quantification in terms of mass per volume of sample. The LMBR and MBR achieved comparable mean PE MPs reduction at 95% and 96%, respectively. The MPs mass reduction in the e-LMBR slightly decreased by 2% compared to that achieved in the LMBR. This potentially indicated the partial breakdown of the MPs due to electrochemical processes. Decreasing and inconsistent NH4-N and PO4-P removal efficiencies were observed over time due to the addition of PE MPs in the MBR and LMBR. In contrast, the integration of electric field in the e-MBR and e-LMBR resulted in consistently high values of conventional contaminant removals of COD (99.72-99.77 %), NH4-N (97.96-98.67%), and PO4-P (98.44-100.00%), despite the MPs accumulation. Integrating electrochemical processes in the e-LMBR led to the development of a stable living membrane (LM) layer, as manifested in the consistently low effluent turbidity 0.49 ± 0.33 NTU. Despite the increasing MPs concentration in the mixed liquor, applying electrochemical processes reduced the fouling rates in the e-LMBR. The e-LMBR achieved comparable efficiencies in contaminant reductions as those observed in the e-MBR, while using a low-cost membrane material.

Benthic litter in fishing grounds of the Northern Adriatic: Role of the trawling fleet as cleaners of the seafloor.

This study represents the baseline of estimation of the potential service provided by fishermen as "cleaners of the sea". The amount, composition and depth distribution of marine litter in fishing grounds of the Northern Adriatic seafloor has been investigated through the fishing for litter (FFL) scheme. Passive FFL campaigns were carried out by trawlers from two of the most important fishing ports in the northern Adriatic, Chioggia and Goro, from May 2020 to May 2021. Over the course of 256 days of fishing, over 6 tons of litter were removed from 265 km2 of seafloor. Abandoned, lost and derelict fishing gears (ALDFG) were the most represented litter category (48 % of the total litter), and of these 67 % were plastic ALDFG (mostly mussel socks and fishing nets). Fouling on plastic waste was analyzed to determine the fraction of collected litter items that could be destinated to recycling. Only a small percentage of the plastic litter analyzed was "clean" from adherent and/or encrusting organisms. Approximately 2.4 tons of plastic were recovered, but, due to the biological colonization of surfaces, they cannot be recycled by using the technologies present in the area.

Performance improvement and application of copper-based nanomaterials in membrane technology for water treatment: A review.

Membrane fouling, including organic, inorganic, and biological fouling, poses enormous challenges in membrane water treatment. Incorporation of copper-based nanomaterials in polymeric membranes is highly favored due to their exceptional antibacterial properties and capacity to improve membrane hydrophilicity. This review extensively explores the utilization of copper-based nanomaterials in membrane technology for water treatment, with a specific focus on enhancing anti-fouling performance. It elaborates on how copper-based nanomaterials improve the surface properties of membrane materials (such as porosity, hydrophilicity, surface charge, etc.) through physical and chemical processes. It summarizes the properties and potential antibacterial mechanisms of copper-based nanomaterials, primarily by disrupting microbial cell structures through the generation of reactive oxygen species (ROS). Furthermore, recent efforts to enhance the environmental sustainability, cost-effectiveness, and recyclability of copper-based nanomaterials are outlined. The attempts to offer insights for the advancement of anti-fouling practices in water treatment through the use of copper-modified polymer membranes.

A comprehensive study on the effects of electrocoagulation integrated in a membrane bioreactor treating sunflower oil refinery wastewater on treatment performance, biological properties, and fouling behavior.

This study evaluated the effects of electrocoagulation integrated in a laboratory-scale membrane bioreactor (MBR), namely EC-MBR, on the treatment performance, activated sludge morphological characterization, and membrane fouling of MBR treating actual sunflower oil refinery wastewater. The EC-MBR system exhibited significantly higher chemical oxygen demand (COD) and oil and grease (O&G) removal efficiency compared to the MBR system. Additionally, both systems achieved excellent turbidity removal, with a percentage above 99%. The membrane fouling rate was higher in the EC-MBR system compared to the MBR system. Despite the decrease in the soluble microbial product (SMP) and extracellular polymeric substance (EPS) concentration in the EC-MBR system, especially their protein fraction, the significant increase in MLSS and carbohydrates/protein ratio, and the decrease in the mixed liquor and the cake layer particles size were the main membrane fouling factors. The membrane fouling resistance distribution showed that the EC-MBR system had a higher percentage of pore blocking resistance compared to the MBR. FTIR analysis identified a greater proportion of carbohydrate compounds in the cake layer of the EC-MBR system. SEM images revealed dense microbial clusters, mainly rod- and oval-shaped bacteria, in the EC-MBR system. Furthermore, EDX analysis detected elements such as Ca, K, O, Al, and P in both systems, with the EC-MBR system showing a higher Al content. The EC-MBR system showed low energy consumption (0.431 kWh m-3) and total operating costs ($0.90 m-3), showcasing its effectiveness and affordability for sustainable wastewater management.

Coupling Low-Frequency Ultrasound to a Crossflow Microfiltration Pilot: Effect of Ultrasonic Pulse Application on Sono-Microfiltration of Jackfruit Juice.

To reduce membrane fouling during the processing of highly pulpy fruit juices into clarified beverages, a crossflow Sono-Microfiltration (SMF) system was employed, strategically equipped with an ultrasonic probe for the direct application of low-frequency ultrasound (LFUS) to the juice just before the entrance to the ceramic membrane. Operating conditions were standardized, and the application of LFUS pulses in both corrective and preventive modes was investigated. The effect of SMF on the physicochemical properties and the total soluble phenol (TSP) content of the clarified juice was also evaluated. The distance of ultrasonic energy irradiation guided the selection of the LFUS probe. Amplitude conditions and ultrasonic pulses were more effective in the preventive mode and did not cause membrane damage, reducing the operation time of jackfruit juice by up to 50% and increasing permeability by up to 81%. The SMF did not alter the physicochemical parameters of the clarified juice, and the measured LFUS energy ranges did not affect the TSP concentration during the process. This study is the first to apply LFUS directly to the feed stream in a pilot-scale crossflow microfiltration system to reduce the fouling of ceramic membranes and maintain bioactive compounds in jackfruit juice.

A Novel Modeling Optimization Approach for a Seven-Channel Titania Ceramic Membrane in an Oily Wastewater Filtration System Based on Experimentation, Full Factorial Design, and Machine Learning.

This comprehensive study looks at how operational conditions affect the performance of a novel seven-channel titania ceramic ultrafiltration membrane for the treatment of produced water. A full factorial design experiment (23) was conducted to study the effect of the cross-flow operating factors on the membrane permeate flux decline and the overall permeate volume. Eleven experimental runs were performed for three important process operating variables: transmembrane pressure (TMP), crossflow velocity (CFV), and filtration time (FT). Steady final membrane fluxes and permeate volumes were recorded for each experimental run. Under the optimized conditions (1.5 bar, 1 m/s, and 2 h), the membrane performance index demonstrated an oil rejection rate of 99%, a flux of 297 L/m2·h (LMH), a 38% overall initial flux decline, and a total permeate volume of 8.14 L. The regression models used for the steady-state membrane permeate flux decline and overall permeate volume led to the highest goodness of fit to the experimental data with a correlation coefficient of 0.999. A Multiple Linear Regression method and an Artificial Neural Network approach were also employed to model the experimental membrane permeate flux decline and analyze the impact of the operating conditions on membrane performance. The predictions of the Gaussian regression and the Levenberg-Marquardt backpropagation method were validated with a determination coefficient of 99% and a Mean Square Error of 0.07.

Enhancing the Separation Performance of Cellulose Membranes Fabricated from 1-Ethyl-3-methylimidazolium Acetate by Introducing Acetone as a Co-Solvent.

Cellulose, a sustainable raw material, holds great promise as an ideal candidate for membrane materials. In this work, we focused on establishing a low-cost route for producing cellulose microfiltration membranes by adopting a co-solvent system comprising the ionic liquid 1-ethyl-3-methylimidazolium acetate ([EMIM]OAc) and acetone. The introduction of acetone as a co-solvent into the casting solution allowed control over the viscosity, thereby significantly enhancing the morphologies and filtration performances of the resulting cellulose membranes. Indeed, applying this co-solvent allowed the water permeability to be significantly increased, while maintaining high rejections. Furthermore, the prepared cellulose membrane demonstrated excellent fouling resistance behavior and flux recovery behavior during a challenging oil-in-water emulsion filtration. These results highlight a promising approach to fabricate high-performance cellulose membranes.

Fabrication of nanocomposite membranes containing Ag/GO nanohybrid for phycocyanin concentration.

In this research, silver/graphene oxide (Ag/GO) nanohybrid was first synthesized and used in production of polysulfone (PSF) ultrafiltration (UF) membranes via phase inversion method for concentrating phycocyanin (PC) and treating methylene blue (MB) dye effluent. Designing the experiment (DOE) using Box-Behnken method by Design Expert software helped to calculate the optimal values of the variables under study. The studied variables included PSF polymer concentration, polyvinyl pyrrolidone (PVP) pore-former concentration and Ag/GO nanohybrid content, which were investigated for their effects on pure water flux (PWF) and MB pigment rejection. According to the results of the DOE, the membrane containing 19.485 wt% PSF, 0.043 wt% PVP and 0.987 wt% Ag/GO was selected as the optimal membrane. Due to the high price of PC as drug, and the importance of removing MB pigment from the effluent of dyeing and textile industries, the membranes were first optimized with MB pigment and then the optimal membrane was used for concentrating PC. The results showed that PWF reaches from 40.05 L.m- 2.h- 1 (LMH) for the neat membrane to 156.73 LMH for the optimized membrane, which shows about 4 times improvement. Compared to the neat membrane, flux recovery ratio (FRR) of the optimized membrane increased by about 20% and its total fouling (Rt) decreased by about 10%. Also, the results showed that the optimized membrane can remove 81.6% of MB, as well as to reject 93.8% of PC.

Amyloid Proteins Adhesive for Slippery Liquid-Infused Porous Surfaces.

Biomimetic slippery liquid-infused porous surfaces (SLIPS) have emerged as a promising solution to solve the limitations of superhydrophobic surfaces, such as inadequate durability in corrosion protection and a propensity for frosting. However, the challenge of ensuring strong, lasting adhesion on diverse materials to enhance the durability of the lubricant layer remains. The research addresses this by leveraging amyloid phase-transitioned lysozyme (PTL) as an adhesive interlayer, conferring stable attachment of SLIPS across a variety of substrates, including metals, inorganics, and polymers. The silica-textured interface robustly secures the lubricant with a notably low sliding angle of 1.15°. PTL-mediated adhesion fortifies the silicone oil attachment to the substrate, ensuring the retention of its repellent efficacy amidst mechanical stressors like ultrasonication, water scrubbing, and centrifugation. The integration of robust adhesion, cross-substrate compatibility, and durability under stress affords the PTL-modified SLIPS exceptional anti-fouling, anti-icing, and anti-corrosion properties, marking it as a leading solution for advanced protective applications.

Application of high-dose UV irradiation as nanofiltration pretreatment for drinking water production: Organic fouling mitigation and micropollutant removal.

Nanofiltration (NF) is being increasingly applied to produce high-quality drinking water; however, its cost-effective operation remains challenging due to the perennial membrane fouling. On account of the low tolerance of common NF membranes to chemical oxidants, this study proposed high-dose UV irradiation as a pretreatment strategy for organic fouling mitigation. Results showed that the permeate flux decline of the membrane with UV-treated feedwater (with a dose of 750 mJ cm-2) was less drastic than that with raw feedwater, but slightly faster as compared to that with UV/Cl2 pretreatment. The final normalized fluxes were 0.69, 0.79, and 0.82, respectively, after 10 h of operation with raw, UV- and UV/Cl2-treated feedwaters. With the characterization of feedwaters and membranes, the fouling was found to be initiated by the adsorption of hydrophilic biopolymers onto the membrane, followed by the deposition of hydrophobic humic substances. Reduction of the "glue" biopolymers was crucial to membrane fouling mitigation. The applicability of UV pretreatment in practice was testified with a pilot-scale UV-NF system where permeate flux of the NF module decreased by 37% after six-week continuous operation. Moreover, UV pretreatment could remove most of the identified pesticides in the feedwater with a removal efficiency over 80% for metolachlor and imidacloprid, but had no or even a negative effect on perfluorinated compounds. This work discloses the efficacy and mechanism of high-dose UV irradiation for NF membrane fouling control, which facilitates future research and application of NF technology.

Control ultrafiltration membrane fouling in Chlorella-laden water treatment by integrated heat-activated peroxydisulfate pre-oxidation and coagulation treatment.

The membrane fouling induced by algal extracellular organic matter (EOM) remain a bottleneck in restricting ultrafiltration (UF) application during harmful algal-water treatment. In current study, the application of heat-activated peroxydisulfate (PMS) and coagulation (Aluminum chlorohydrate, PACI) on membrane fouling behavior during Chlorella-laden water treatment was investigated. The membrane fouling mechanism was analyzed using the extended Derjaguin-Landau-Verwey-Over-beek (XDLVO) theory. The results revealed that separated heat-activated PMS could enhance the filtration flux of EOM at high PMS does >0.2 mM, whereas the membrane fouling was further alleviated by combined heat-activated PMS (0.2-1.0 mM) and PACI (20 mg/L) treatment, especially at low PMS dose. Combined heat-activated PMS and PACI pretreatment could effectively increase the adhesive repulsion between membrane and foulants and reduce the cohesion free energies between organic foulants than those by separated heat-activated PMS treatment, making the initial filtration flux reduced and the cake layer looser. Moreover, the organic foulants of proteins, polysaccharides, and humic-like organics were removed. Cake formation was the major fouling mechanism when EOM was treated with/without separated heat-activated PMS treatment, whereas the membrane fouling mechanism was changed from cake layer formation to pore blocking after combined heat-activated PMS and PACI treatment. Overall, this research provided a feasible method in membrane fouling control during Chlorella -laden water treatment.

Anaerobic dynamic membrane bioreactor treating sulfamethoxazole wastewater: advantages of dynamic membrane and its fouling mechanism.

Discharge of improperly treated sulfamethoxazole (SMX) wastewater seriously threats environmental security and public health. Anaerobic dynamic membrane bioreactors (AnDMBRs) technology would be cost-effective for SMX wastewater treatment, considering its low cost and satisfactory treatment efficiency. The performance of AnDMBR, though demonstrated to be excellent in treating many types of wastewaters, was for the first time investigated for treating SMX wastewater. Particular efforts were devoted to elucidating the advantages of dynamic membrane (DM) and the governing mechanism responsible for DM fouling with the presence of SMX. The threshold SMX concentration for AnDMBR was found to be 90 mg/L and the AnDMBR exhibited excellent removal efficiency of COD (90.91 %) and SMX (88.95 %) as well as satisfactory acute toxicity reduction rate (88.84 %). It was noteworthy that the DM made indispensable contributions to the removal of COD (14.26 %) and SMX (22.20 %) as well as the acute reduction of toxicity (25.81 %). The presence of SMX significantly accelerated DM fouling mainly by increasing its specific resistance, which was attributed to the increased content of small particles, high-valence metal ions and EPS content (mainly hydrophobic proteins), resulting in a denser DM structure with lower porosity. Besides, the biofouling-related bacteria (Firmicutes) was found to be enriched in the DM with the presence of SMX.

Promoted production of Fe(IV)/Fe(V) intermediates in the calcium peroxide/ferrate(VI) process for low-damage removal of algal contaminants and membrane fouling control.

Ultrafiltration (UF) is widely employed for harmful algae rejection, whereas severe membrane fouling hampers its long-term operation. Herein, calcium peroxide (CaO2) and ferrate (Fe(VI)) were innovatively coupled for low-damage removal of algal contaminants and fouling control in the UF process. As a result, the terminal J/J0 increased from 0.13 to 0.66, with Rr and Rir respectively decreased by 96.74 % and 48.47 %. The cake layer filtration was significantly postponed, and pore blocking was reduced. The ζ-potential of algal foulants was weakened from -34.4 mV to -18.7 mV, and algal cells of 86.15 % were removed with flocs of 300 µm generated. The cell integrity was better remained in comparison to the Fe(VI) treatment, and Fe(IV)/Fe(V) was verified to be the dominant reactive species. The membrane fouling alleviation mechanisms could be attributed to the reduction of the fouling loads and the changes in the interfacial free energies. A membrane fouling prediction model was built based on a long short-term memory deep learning network, which predicted that the filtration volume at J/J0= 0.2 increased from 288 to 1400 mL. The results provide a new routine for controlling algal membrane fouling from the perspective of promoting the generation of Fe(IV)/Fe(V) intermediates.

Dielectric Barrier Discharge (DBD) enhanced Fenton process for landfill leachate nanofiltration: Organic matter removal and membrane fouling alleviation.

This study investigated a sustainable approach through dielectric barrier discharge (DBD) enhanced Fenton technology coupling nanofiltration (NF) process for landfill leachate treatment. The DBD/Fe(II)/H2O2 system exhibited significant synergistic effects, removing 55.07 % of TOC and 53.79 % of UV254 within 60 min, respectively. Additionally, the DBD/Fe(II)/H2O2 system demonstrated exceptional performance in removing fluorescent substances and large molecular organic compounds, thereby reducing the formation of cake layer on the nanofiltration membrane. Moreover, membrane flux increased by 2.34 times, with reversible and irreversible resistances decreasing by 75.79 % and 81.55 %, respectively. Quenching experiments revealed ·OH as the primary active species for perfluorooctanoic acid (PFOA) degradation in the DBD/Fe(II)/H2O2 process. The degradation pathway of PFOA was also elucidated via capillary electrophoresis-quadrupole time-of-flight mass spectrometry analysis. Correlation analysis indicated that TOC and EEM were the primary fouling factors. Lastly, through an assessment of energy consumption, economic costs, and carbon dioxide emissions, the advantages and practical application potential of the DBD/Fe(II)/H2O2 system were demonstrated. In summary, the DBD/Fe(II)/H2O2 system emerges as a feasible strategy for NF pretreatment, holding immense potential for treating landfill leachate.

Treatment of pulp and paper mill effluent through combined aerobic and anaerobic suspended fixed-bed bioreactor.

This study explored using ultrafiltration (UF) membranes to treat pulp and paper mill wastewater, implementing a novel Taguchi experimental design to optimize operating conditions for pollutant removal and minimal membrane fouling. Researchers examined four factors: pH, temperature, transmembrane pressure, and volume reduction factor (VRF), each at three levels. Optimal conditions (pH 10, 25°C, 6 bar, VRF 3) led to a 35% reduction in flux due to fouling and high pollutant rejections: total hardness (83%), sulfate (97%), spectral absorption coefficient (SAC254) (95%), and chemical oxygen demand (COD) (89%). Conductivity had a lower rejection rate of 50%. Advanced imaging techniques like atomic force microscopy (AFM) and scanning electron microscopy (SEM) revealed reduced membrane fouling under these conditions. The Taguchi method effectively identified optimal conditions, significantly improving wastewater treatment efficiency and promoting environmental sustainability in the pulp and paper industry. PRACTITIONER POINTS: This study optimized UF membrane conditions for pulp and paper mill wastewater, reducing fouling and enhancing pollutant removal, offering practical strategies for industrial treatment. AFM and SEM provided key insights into membrane fouling and mitigation, promoting real-time diagnosis and optimization for enhanced treatment efficiency. Prioritizing anaerobic fixed-bed systems in wastewater treatment is beneficial for achieving high COD removal efficiency. Optimizing hydraulic retention time (HRT) in these systems can further improve their overall effectiveness and sustainability.

Nano-confined catalysis with Co nanoparticles-encapsulated carbon nanotubes for enhanced peroxymonosulfate oxidation in secondary effluent treatment: Water quality improvement and membrane fouling alleviation.

Despite widespread deployment and investigation of ultrafiltration (UF) for secondary effluent purification, the challenge of membrane fouling due to effluent organic matter (EfOM) remains formidable. This study introduced a novel pretreatment method utilizing Co nanoparticles-encapsulated carbon nanotubes activated peroxymonosulfate (Co@CNT/PMS) to degrade EfOM and mitigate membrane fouling. Characterization of Co@CNT revealed the efficient encapsulation of Co nanoparticles within nanotubes, which notably enhanced the catalytic degradation of bisphenol A and typical organics. The tube-encapsulated structure increased the concentration of reactive species within the confined nanoscopic space, thereby improving the probability of collisions with pollutants and promoting their degradation. The Co@CNT/PMS pretreatment led to substantial reductions in aromatic compounds, fluorescent components, and both high and middle molecular weight substances. These changes proved crucial in diminishing the fouling potential in subsequent UF processes, where reversible and irreversible fouling resistances decreased by 97.1 % and 72.8 %, respectively. The transition volume from pore blocking to cake filtration markedly increased, prolonging the formation of a dense fouling layer. Surface properties analysis indicated a significant reduction of pollutants on membrane surfaces after the Co@CNT/PMS pretreatment. This study underscored the efficacy of confinement-based advanced oxidization pretreatment in enhancing UF performance, presenting a viable resolution to membrane fouling.

Forward osmosis membrane with lightweight functionalised multiwall carbon nanotube nanofillers.

Thin-film nanocomposite (TFN) membranes with a polyamide (PA) active layer modified with carbon nanotubes (CNTs) hold promise for water desalination and wastewater reuse via forward osmosis (FO). We hypothesise that modifying the PA active layer with hydroxyl-functionalised multi-wall carbon nanotubes (f-MWCNTs) will enhance the water flux of the FO membrane while maximising salt rejection. TFN membranes were modified using in situ interfacial polymerisation, with varying f-MWCNT mass content to minimise agglomeration. These modified FO membranes are designated as CTFN-x, where x represents the mass content of f-MWCNTs, ranging from 0.001%, CTFN-1 to 0.008%, CTFN-8 (w/v). The surface properties of CTFN-x were characterised using electron microscopy, atomic force microscopy, and molecular spectroscopy. IR spectroscopic data confirm the successful adherence of f-MWCNTs as a bridging agent between the 1,3-phenylenediamine (MPD) and trimesoyl chloride (TMC) polymers, preserving FO membrane integrity. The CTFN-4 FO membrane shows the highest water flux (29 LMH) and the lowest reverse salt flux (2.90 gHM), attributed to preferential water flow channels in the f-MWCNTs. The integration of f-MWCNTs into the active layer improved water flux, reduced reverse salt flux, and enhanced the antifouling properties of FO membranes.

Membrane fouling characteristics and mechanisms in coagulation-ultrafiltration process for treating microplastic-containing water.

Microplastics (MPs) are recognized as a significant challenge to water treatment processes due to their ability to adsorb or accumulate alginate foulants, impacting the coagulation-ultrafiltration (CUF) process. In this study, the mechanisms of membrane fouling caused by MPs under varying dosages of polymeric aluminum chloride (PAC) coagulant in the CUF process were investigated. It was revealed that MPs contribute to membrane fouling, which initially intensifies and then alleviates as coagulant concentration increases, with a turning point at 0.05 mM PAC dosage. The most significant alleviation of membrane fouling was observed at 0.2 mM PAC dosage. An in-depth analysis of interfacial interaction energy changes during filtration was conducted using the extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory, demonstrating how MPs alter the interaction forces between foulants and the membrane surface, leading to either the exacerbation or mitigation of fouling. Additionally, it was shown that at optimal coagulant concentrations, the presence of MPs promotes the formation of a loose and porous cake layer, disrupting the original structure and creating a more open block structure, thereby alleviating membrane fouling. These findings provide valuable insights for optimizing the CUF process in microplastic-containing water treatment, presenting a novel approach to enhancing efficiency and reducing membrane fouling.

Fluorine-Free Amphiphobic SBS/PAN Micro/Nanofiber Membrane by Integrating Click Reaction with Electrospinning for Efficient and Recyclable Air Filtration.

The membrane fouling derived from the accumulated dust pollutants and highly viscous oily particles causes irreversible damage to the filtration performance of air filters and results in a significant reduction in their service life. However, it is still challenging to construct high-efficiency and antifouling air filtration membranes with recyclable regeneration. Herein, the fluorine-free amphiphobic micro/nanofiber composite membrane was controllably constructed by integrating click chemistry reaction and electrospinning technique. Low-surface-energy fibers were constructed by a thiol-ene click chemical reaction between mercaptosilane and vinyl groups of polystyrene-butadiene-styrene (SBS), combined with hydroxyl-terminated poly(dimethylsiloxane) during the electrospinning process. The functional air filter is then prepared by the two-layer composite strategy. Because of the advantages of liquid-like fibrous surface and micro/nanofibrous porous structure, SBS/PAN composite membrane simultaneously shows superior antifouling performances of pollutants and filtration efficiency of over 97% PM0.3 removal. More importantly, the antifouling fibrous membrane still presents a stable and efficient filtration efficiency after multiple washes. Its service life in dust filtration environments is approximately 1.7 times longer than that of the substrate membrane. This work may provide a significant reference for the design of antifouling fiber membranes and high-efficiency air filters with long life spans and reusability.