Challenges in Residual Bearing Removal: A Rare Case of Mobile Bearing Fracture in Unicompartmental Knee Arthroplasty with Literature Review.

BACKGROUND: Mobile bearing fracture is a rare long-term complication of unicompartmental knee arthroplasty (UKA), and relevant reports are sparse. Hence, its treatment options need further exploration. CASE PRESENTATION: This study presents the case of fracture of a polyethylene insert that occurred 12 years after mobile bearing medial UKA in a 75-year-old overweight woman who then underwent surgical intervention at our institution. However, we encountered significant challenges in removing the fragments from the broken bearing, resulting in retention of the remaining one-third of the fragment. We solved this problem by replacing the fractured insert with thicker mobile bearing. During the 1-month postoperative follow-up, the patient achieved good range of motion and excellent satisfaction, with no reported complications and a Knee Society Score of 90. Additionally, we reviewed the literature on the treatment for mobile bearing fractures after UKA. CONCLUSIONS: Bearing fracture is a rare cause of failure of mobile bearing UKA. This case highlights the challenges of UKA fracture bearing retrieval and underscores that mobile bearing replacement can be an effective intervention. The case we report shows that when removal of a residual meniscal bearing in a posterior dislocation is difficult to achieve, compromise may be an appropriate option because it does not cause additional complaints to the patient. This case emphasizes the importance of the surgeon having a thorough preoperative understanding of the location and potential pitfalls of fracture fragments in such situations.

Advantages and limitations of mobile-bearing unicompartmental knee arthroplasty: an overview of the literature.

INTRODUCTION: Interest in unicompartmental knee arthroplasty (UKA) has recently grown. Mobile bearing UKA, in which the bearing is not fixed but rather perfectly conforms with femoral and tibial components and moves completely passively between the femoral and tibial implant, has now been used for approximately half a century. AREAS COVERED: Alongside the recognized advantages of UKA, the mobile-bearing variant benefits from an extremely low rate of polyethylene wear and tolerable minor malalignment. Revision rates for UKA have been reported to exceed those of total knee arthroplasty, but long-term survival rates and outcomes from mobile-bearing UKA have been found to be satisfactory. In addition to the lateral osteoarthritis and loosening, which are main complications of UKA, bearing dislocation is a specific complication of mobile bearing UKA. Fractures and valgus subsidence are more prevalent than in the cementless UKA. While these continue to be features to be addressed, they have been partially solved. EXPERT OPINION: Given the manifold benefits of UKA, its application could be extended to a larger patient population. Successful outcomes rely on careful patient selection and the surgeon's extensive familiarity with the procedure. Looking ahead, the incorporation of robotic surgery, already a feature of some fixed-bearing UKAs, might shape the future trajectory of mobile-bearing UKA.

Propensity of the tight mid-flexion and loose flexion gap despite the adjustment of extension and flexion gaps in Oxford unicompartmental knee arthroplasty: retrospective study.

PURPOSE: A well-balanced joint gap is necessary in Oxford unicompartmental knee arthroplasty (OUKA) to prevent mobile-bearing dislocation. While the gaps between 20° (extension) and 100° (flexion) are precisely adjusted using the incremental mill system, there has been insufficient evaluation of gaps in other angles. We hypothesized that the gap is not always the same in other angles. This retrospective study aimed to evaluate the gap in full-extension (0°), mid-flexion (60°) and deep flexion (130°) for comparison with those in extension and flexion gaps. METHODS: We evaluated 119 knees in 83 patients (51 females, 31 males, aged 71.9 years). The full-extension and mid-flexion gaps were compared with the extension gap, and the deep flexion gap was contrasted with the flexion gap. Each gap was classified into isometric, tight or loose, for evaluation of contributing factors. RESULTS: Although the full-extension gap tended to be isometric (45%), the mid-flexion tended to be tight (48%), whereas the deep-flexion was loose in most knees (84%) (P = 0.002). The tight mid-flexion and loose deep flexion gap pattern accounted for 44% of the total knees, especially so with smaller femoral components (P = 0.004). CONCLUSION: Our results highlight the propensity of tight mid-flexion and loose flexion gap despite the adjustment of extension and flexion gaps in OUKA. Although the effect of such a minor gap imbalance is still unknown, the pattern was more prevalent in patients with smaller-sized femoral components. Use of a larger femoral component may equalize the gap throughout the motion arc.

Unicompartmental knee replacement: controversies and technical considerations.

BACKGROUND: Unicompartmental knee replacement (UKR) is one of the effective interventions for the treatment of symptomatic knee osteoarthritis. Moreover, it has multiple advantages over total knee arthroplasty (TKA), including reduced intraoperative blood loss, decreased risk of transfusion, and faster recovery. This study aimed to discuss critical technical considerations regarding UKR and some of the controversies and updates. METHODS: We conducted a review to provide an overview of the controversies and technical considerations about UKR in several aspects. Only peer-reviewed articles were included, up to December 2023 using PubMed, Google Scholar, ERIC, and Cochrane database for systematic reviews databases. RESULT: UKR is associated with superior patient-reported clinical and functional outcomes, as well as shorter hospital stays, fewer postoperative complications, and revealed favorable outcomes in patients' return to sport. The choice between mobile- and fixed-bearing prostheses depends, in part, on the surgeon's preference. The mobile-bearing UKR is a less constrained prosthesis and can potentially result in less wear, but it is more technically demanding. While no significant difference between mobile-bearing versus fixed-bearing prostheses, cementless is superior to cemented design. Furthermore, UKR can be a good alternative for high tibial osteotomy (HTO) and still can be considered after a failed HTO. Lastly, recent reviews have shown a revision rate comparable to that of TKA. This is probably influenced by Improved comprehension of the best indications, patient selection criteria, as well as of the design, materials, and technological advances. CONCLUSION: UKR treatment for unicompartmental knee osteoarthritis is secure and effective. Based on clinical and functional outcomes, decreased morbidity and mortality, and cost-effectiveness, long-term studies suggest that UKR is superior to TKA. Further investigation in this area is warranted.

3D kinematics of tibiotalar motion in patients with mobile bearing and fixed bearing total ankle arthroplasty: In vivo videofluoroscopic feasibility study.

BACKGROUND: As total ankle arthroplasty (TAA) is an increasingly common surgical intervention for patients with end-stage ankle arthritis, there is a need to better understand the dynamic performance of prosthetic implants during activities of daily living. Our purpose was to quantify and compare relative tibiotalar motion during gait in persons with a fixed-bearing (FB) and mobile-bearing (MB) total ankle arthroplasty. We hypothesized a FB prosthesis would have lower tibiotalar range of motion (ROM). METHODS: Patients at least 12 months postoperative with either a FB (n=5) or MB (n=3) total ankle arthroplasty were tested. We used high-speed biplanar videoradiography to quantify tibiotalar kinematics during self-selected gait. Angular and linear ROM in three axes were compared between the groups. RESULTS: ROM for dorsiflexion-plantarflexion, internal-external rotation, and inversion-eversion angles in FB subjects averaged 7.47±4.05°, 7.39±3.63°, and 4.51±2.13°, respectively. ROM in MB subjects averaged 6.74±2.04°, 6.28±4.51°, and 5.68±2.81°, respectively. Linear ROM along anteroposterior, mediolateral, and superior-inferior axes in FB subjects averaged 1.47±2.07 mm, 1.13±1.49 mm, and 0.28±0.30 mm, respectively. Linear ROM in MB subjects averaged 0.68±1.44 mm, 0.60±1.41 mm, and 0.20±0.13 mm, respectively. We found no significant difference between the two groups for any of these ROM parameters (p>0.05). CONCLUSION: Total ankle arthroplasty using either FB or MB design appears to confer similar ankle motion during the gait cycle in this biplanar fluoroscopic model. LEVEL OF EVIDENCE: Level IV, case series.

Comparison of revision rates and epidemiological data of a single total knee arthroplasty system of different designs (cruciate retaining, posterior stabilized, mobile bearing, and fixed bearing): a meta-analysis and systematic review of clinical trials and national arthroplasty registries.

BACKGROUND: This study aimed to meta-analyze epidemiological data, revision rates, and incidences of different designs of a single Total Knee Arthroplasty System and compare these factors across different countries. METHODS: A systematic review was conducted on clinical studies and arthroplasty registries of ATTUNE TKA from 1999 to 2020. The main endpoints analyzed were revision rates and epidemiological data. RESULTS: The average age of patients was 67.8 years, with a gender distribution of 60% female and 40% male. The pooled average BMI was 29.4 kg/m2. Eight clinical studies showed a pooled revision rate per 100 observed CY of 0.5 (n = 1343 cases). Cumulative revision rates after 1, 3, and 5 years varied among registries, with the Swiss registry having the highest revision data (after 5 years: 6.3%) and the American registry having the lowest revision data (after 5 years: 1.7%). A comparison of the revision rates of mobile bearing and fixed bearing (41,200 cases) as well as cruciate retaining and posterior stabilized (n = 123,361 cases) showed no significant advantage in the first 5 years after implantation. CONCLUSION: In conclusion, pooled data from 41,200 cases of TKA with a single Total Knee Arthroplasty System in two arthroplasty registries revealed that there was no significant difference in revision rates between the mobile bearing and fixed bearing design within the first 5 years after implantation. In addition, a comparison of the revision rates in n = 123,361 cases showed no significant advantage for cruciate retaining or posterior stabilized in the first 5 years after implantation.

Mid-term survivorship and clinical outcomes of revision knee arthroplasty using a mobile bearing tibial tray: A single-center registry review.

BACKGROUND: Revision total knee arthroplasty can successfully restore function and relieve pain for patients with failed knee replacements. Mobile-bearing implants were designed to provide greater congruency between the implant and the polyethylene insert. The goal of this study was to review the clinical outcomes and survivorship for a revision mobile-bearing tibial design. METHODS: A retrospective outcomes review was conducted to assess survivorship and clinical outcomes for a mobile bearing tibial tray, used with metaphyseal sleeves, in revision total knee arthroplasty. RESULTS: At time of furthest follow-up, KM estimates (95% CI; n with further follow-up) for all-cause revision were 82.5% (75.8%; 87.5%; 42) at 7 years for the clinical assumption (CA), and 88.5% (84.4%,91.6%; 53) at 13 years for the registry assumption (RA). For revision of the tray as the endpoint, survivorship estimates were 93.4% (87.0%,96.7%; 42) at 7 years for CA, and 96.2% (93.2%,97.9%; 53) at 13 years for RA. CONCLUSION: In this single-center registry evaluation, we found excellent mid-term survivorship and clinical outcomes for a mobile-bearing tibial tray used with metaphyseal sleeves in revision total knee arthroplasty.

In Vivo Total Ankle Arthroplasty Kinematic Evaluation: A Prospective Radiostereometric Analysis.

Ankle osteoarthritis (OA) represents a significant social burden and is one of the main causes of chronic disability in a rapidly growing part of the world's population. Total ankle arthroplasty (TAA) has become increasingly popular despite the poor results obtained with the first dedicated designs. The purpose of this paper was to evaluate the ankle kinematics, in vivo and under weight-bearing conditions, of a TAA through a dynamic model-based radiostereometric analysis (MB-RSA). The clinical evaluation was performed by administering the American Orthopaedic Foot and Ankle Society ankle-hindfoot score and Short Form-36 questionnaires. The kinematic evaluation was conducted through MB-RSA during the execution of an open kinetic chain and a closed kinetic chain motor task. Double radiographic images of the ankle joint were processed using dedicated software to obtain a 3D reconstruction of the ankle prosthetic components' motion. Eighteen patients (five females) completed the clinical and instrumental preoperative and postoperative evaluations (age 59.1 ± 10.3). All clinical scores showed a marked improvement (p < 0.005). During the closed kinetic chain motor tasks, the ankle showed a total range of motion (ROM) in dorsi-plantarflexion of 19.84°. The parameters in varus-valgus were recorded. Physiological motion can be achieved in TAA, characterized by a wide range of motion and coupling of movements on the three planes. The results of the present work may help to understand the real movement of a widespread TAA model and possibly to improve future designs and instrumentation.

Femoral Coronal Malalignment is Associated With Failure in Mobile-Bearing Medial Unicompartmental Knee Arthroplasty.

BACKGROUND: Femur-first (FF) technique for mobile-bearing medial unicompartmental knee arthroplasty (UKA) has been described as an alternative to tibia-first (TF) technique. The aim of this study was to compare the radiographic results in UKAs using FF or TF techniques and their influence on failure rates. METHODS: We retrospectively reviewed 288 UKAs with a minimum 2-year follow-up. There were 147 knees in the TF and 141 knees in the FF cohorts. Alignment parameters and overhang were assessed as outliers and far outliers. The mean follow-up was 6 years (range, 2 to 16), the mean age was 63 years (range, 27 to 92), and 45% of patients were women. Univariate and multivariate statistical analyses were carried out with Cox regression models. RESULTS: There were 13 and 6 revisions in the TF and FF cohorts, respectively. The FF had lower rates of femoral coronal alignment (FCA) or femoral sagittal alignment outliers compared to the TF (5.7% versus 19%, P = .011). Tibial coronal alignment and tibial sagittal alignment did not significantly differ between the techniques (22.7% in FF versus 29.9% in TF, P = .119). Overhang outliers did not differ significantly between the groups. Younger age was associated with a higher revision rate (P = .006), while FF versus TF, sex, body mass index, and postoperative mechanical axis did not show statistically significant associations. In multivariate analysis, FCA outliers and younger age were significantly associated with revision. CONCLUSIONS: The FF technique in mobile-bearing UKA resulted in fewer FCA outliers compared to TF. Despite improved knee alignment with the FF technique, FCA outliers and younger age were associated with a higher revision rate, independent of technique.

Mobile medial pivot (lateral slide)-type total knee arthroplasty exhibited different motion patterns between under anaesthesia and weight-bearing condition.

PURPOSE: Total knee arthroplasty (TKA), which has medial pivot and mobile-bearing mechanisms, has been developed and clinically used. However, the in vivo dynamic kinematics of the mobile medial pivot-type TKA (MMPTKA) is unclear. This study analysed the in vivo kinematics of MMPTKA in weight-bearing and nonweight-bearing conditions. METHODS: The study included 10 knees that underwent primary TKA using MMPTKA. After TKA, lateral view radiographs of the knee in full extension, 90° of flexion and passive full flexion were taken under general anaesthesia in the nonweight-bearing condition. At least 6 months postoperatively, knee motion during squatting from a weight-bearing standing position was observed using a flat-panel detector and analysed using the three-dimensional-to-two-dimensional image registration technique. RESULTS: Under anaesthesia: in passive full flexion, the anteroposterior (AP) locations of the femoral component's medial and lateral distal points were 10.2 and 16.0 mm posterior, and the rotational angles of the femoral component's X-axis (FCX) and insert were 8.1° external rotation and 18.5° internal rotation to full extension, respectively. Squatting: the AP translations of the femoral component's medial and lateral most distal points were 2.2 and 6.4 mm, and the rotational angles of the FCX and insert were 5.7° and 1.6° external rotation, respectively. Significant differences were observed in the AP translation of the femoral component's medial and lateral most distal points and changes in the insert's rotational angle when comparing under anaesthesia and squatting. CONCLUSIONS: The kinematics of the insert in MMPTKA was significantly influenced by loading and muscle contraction. The femoral component exhibited substantial external rotation and posterior translation under anaesthesia, which may contribute to achieving an optimal range of motion. The insert remained relatively stable during squatting and minimal rotation was observed, indicating good stability. MMPTKA was expected to demonstrate rational kinematics by incorporating mobile and medial pivot mechanisms. LEVEL OF EVIDENCE: Level IV, prospective biomechanical case series study.

Simultaneous Post and Cone Fractures of a Polyethylene Insert in a Mobile-Bearing Posterior-Stabilized Total Knee Arthroplasty.

We report a novel case of the simultaneous post and cone fractures of a polyethylene (PE) insert in a mobile-bearing posterior-stabilized total knee arthroplasty. Twelve years after the primary total knee arthroplasty, the 72-year-old male patient presented with a recurring right knee instability and was diagnosed with the wear of the PE insert based on physical and radiological examinations. Revision surgery was performed. The post and cone of the PE insert had fractured simultaneously. Moreover, the femoral and tibial components were in direct contact with each other. One year post-revision, knee function had improved. To diagnose a PE breakage, such as a post or cone fracture, surgeons should consider the possibility of PE breakage even in the absence of pain since patients might complain of subjective instability only.

No differences in long-term clinical outcomes and survival rate of navigation-assisted versus conventional primary mobile-bearing total knee arthroplasty: A minimum 10-year follow-up.

PURPOSE: This study aimed to compare long-term clinical and radiographic outcomes and survival rates between navigation-assisted (NAV) total knee arthroplasty (TKA) and conventional (CON) TKA using a mobile-bearing insert. METHODS: From May 2008 to December 2009, 45 and 63 mobile-bearing TKA patients were enroled in the CON- and NAV-TKA groups with 146.8 months follow-up, respectively. Clinical outcomes (Western Ontario and McMaster University Osteoarthritis Index and Knee Society Scores), radiographic outcomes (hip-knee-ankle [HKA], lateral distal femoral, medial proximal tibial, γ, and δ angles), and survivorship were compared between both groups. RESULTS: The number of HKA angle outliers (more than 3 degrees or less than -3 degree) was significantly lower in the NAV-TKA group (24.4% vs. 9.5%, p = 0.036) than in the CON-TKA group. However, long-term clinical outcomes were similar between both groups. The cumulative survival rate (best-case scenario) was 98.3% in the CON-TKA group and 97.5% in the NAV-TKA group, with no significant difference between the groups (p = 0.883). CONCLUSION: Long-term clinical outcomes and survival rates were similar between the two groups despite fewer outliers of postoperative lower-limb alignment in the NAV-TKA group. Excellent survival rates were observed in both groups using mobile-bearing inserts. LEVEL OF EVIDENCE: Level IV, case series.

Safe bearing region for avoiding meniscal bearing impingement and overhang in mobile-bearing unicompartmental knee arthroplasty.

The purposes of this study were to propose a quantitative method of bearing overhang to minimize the effect of bearing spinning on mobile-bearing unicompartmental knee arthroplasty (MB UKA), suggest and apply safe bearing regions in daily activities. The overhang distance and area were calculated for neutral and spinning positions. The safe bearing regions were based on the relationship between bearing overhang and linear wear rate. Eleven patients were included in an in-vivo experiment under dual fluoroscopic imaging following medial MB UKA. The bearing position was tracked by minimal joint space width, and the bearing overhang was calculated accordingly. Due to an equal contribution of 1 mm increase in medial overhang and 30 mm2 overhang areato wear rate, the maximum effect of potential bearing spinning on medial overhang distance was approximately three times as large as the overhang area. The safe bearing distance and area regions were rectangles and arches with different scales for different size combinations of bearing, femoral and tibial components. The maximum bearing overhang area during lunge (R = 0.76, p = 0.006) and open-chain exercise (R = 0.68, p = 0.02) significantly correlated with the overhang area in standing. The overhang area can be an appropriate parameter for evaluating dislocation degree less affected by potential bearing spinning than the overhang distance in clinical practice. The corresponding safe overhang area regions were proposed for surgical planning and postoperative dislocation degree evaluation. The bearing overhang area in static standing posture can be a valuable reference to estimate the dynamic overhang area and dislocation degree during motion.

Preoperative valgus-corrected hip-knee-ankle angle and medial meniscal extrusion are useful for evaluating postoperative alignment in mobile-bearing UKA.

Purpose: The purposes of the study were to analyze the correlation between preoperative variables (valgus corrected hip-knee-ankle angle (vcHKA), medial osteophyte areas of the tibia and femur, and medial meniscus extrusion (MME)) and the postoperative alignment in mobile-bearing unicompartmental knee arthroplasty (UKA). Methods: This study enrolled 109 patients (118 knees) who underwent mobile-bearing UKA between January 1, 2019 and January 1, 2023, retrospectively. Radiographic parameters, including the HKA, hip-knee-shaft angle (HKS), and valgus-corrected femorotibial angle (vcFTA), were measured using preoperative radiographs. The vcHKA was calculated as vcFTA - HKS. The medial osteophyte areas of the tibia and femur and MME were measured using knee magnetic resonance imaging (MRI). Simple and multiple linear regression analyses, univariate and multivariate logistic regression analyses, and receiver operating characteristic (ROC) curves were performed. Results: In total, 109 patients (118 knees) were enrolled in this study. In the multiple linear regression analysis, vcHKA (ß = 0.732, 95 % confidence interval (95%CI) = 0.582 to 0.881; p < 0.001) and MME (ß = 0.203, 95%CI = 0.001 to 0.405; p = 0.049) were positively correlated with postoperative HKA, and postoperative HKA was modeled according to the following equation: 45.420 + (0.732° * vcHKA) + (0.203 mm × MME). In the multivariate logistic regression analysis, vcHKA (odds ratio (OR) = 2.007, 95 % CI = 1.433 to 2.810, p < 0.001) was associated with postoperative valgus malalignment independently. In the ROC curve, vcHKA (cutoff value: 180°) was predictive of postoperative valgus malalignment, with an accuracy (95%CI) of 0.862 (0.780-0.944). Conclusion: Overcorrection of a varus knee under valgus stress radiograph (VSR) and excessive MME on preoperative MRI increase the possibility of overcorrection of postoperative alignment in mobile-bearing UKA.

The effect of different posterior inclinations of tibial component on tibiofemoral contact pressures after unicompartmental knee arthroplasty.

BACKGROUND: Different posterior inclinations of tibial component after unicompartmental knee arthroplasty (UKA) may lead to different biomechanical characteristics of the knee joint. This finite element study was designed to investigate the tibiofemoral contact pressures after UKA with different posterior inclinations of tibial component. METHODS: Finite element model of a healthy knee joint was constructed, and mobile-bearing (MB) UKA models with 5 different posterior inclinations (3°, 5°, 7°, 9° and 11°) of tibial components were simulated. The maximum contact pressures of tibial plateau cartilage in the lateral compartment and polyethylene insert in the medial compartment were calculated based on the ground reaction force and the angle of the knee flexion obtained by 3D motion capture system. RESULTS: The loading ratio of medial and lateral compartments during standing stance (medial 54.49%, lateral 45.51%) and tibial anterior displacement (134 N, 3.89 mm) of healthy knee was basically consistent with previous experimental data. The maximum contact pressures of the medial meniscus and lateral tibial plateau cartilage of the healthy knee during standing stance were 2.14 MPa and 1.57 MPa, respectively. At the static standing phase, the maximum contact pressures of the polyethylene insert decreased from 17.90 to 17.29 Mpa, and the maximum contact pressures of the tibial plateau cartilage in the lateral compartment increased from 0.81 to 0.92 Mpa following an increase in the posterior inclination of the tibial component. At the first peak of ground reaction force, the maximum contact pressures of polyethylene insert increased from 22.37 to 25.16 MPa, and the maximum contact pressures of tibial plateau cartilage in the lateral compartment increased from 3.03 to 3.33 MPa, with the increase in the posterior inclination of the tibial component. At the second peak of ground reaction force, the maximum contact pressures of polyethylene insert decreased from 2.34 to 2.22 MPa with the increase in posterior inclination of tibial component. CONCLUSION: The preoperative and postoperative finite element models of MB UKA were well established. The results showed that the maximum contact pressures of the polyethylene insert did not change significantly with the increase in the posterior inclination of the tibial prosthesis, while the maximum contact pressures of the tibial plateau cartilage of the lateral compartment increased when the posterior inclination of the tibial prosthesis was > 7°. Our results also show that the maximum contact pressures were greater with an excessive inclination angle (11°) of the tibial component, and the pressures of the tibial plateau cartilage in the lateral compartment were more concentrated on the posterior area. This study, therefore, proposes that excessive osteotomy should be avoided.

Less wear in deep-dished mobile compared to fixed bearing total knee arthroplasty of the same design at 5-year follow-up: a randomised controlled model-based Roentgen stereophotogrammetric analysis trial.

PURPOSE: The aim of this prospective randomised controlled study was to compare wear characteristics and functional outcome between deep-dished mobile bearing (MB) and fixed bearing (FB) cemented total knee arthroplasty (TKA). We hypothesised that deep-dished MB reduces polyethylene wear and improves patient-reported outcome measures. METHODS: A total of 50 patients were randomised to receive a MB or FB tibia component of the same cemented TKA design. Patients were evaluated over a 5-year follow-up period. Medial and lateral wear were assessed using model-based Roentgen Stereophotogrammetric Analysis (RSA) and compared with the direct postoperative minimal joint space measurement. Functional outcome was assessed by the clinician-derived KSS and OKS, WOMAC, LEAS, and FJS-12. All data were derived using a general linear mixed model. RESULTS: At 5-year follow-up, decreased wear in the MB compared to the FB group was observed on the lateral side (0.07 ± 0.17 mm, p = 0.026), but not on the medial side (0.31 ± 0.055 mm, p = 0.665). Functional outcomes improved with a statistical significant effect over time, with no significant differences between groups (all p > 0.17). CONCLUSION: This model-based RSA study with 5-year follow-up showed that cemented deep-dished MB reduced lateral polyethylene wear as compared to FB in a single TKA system, whilst clinical outcomes were comparable. Longer follow-up is needed to establish clinical implications of these altered wear patterns and determine type of wear. LEVEL OF EVIDENCE: Level 1 randomised controlled trial.

Mechanisms of mobile bearing dislocation in lateral unicompartmental knee replacement.

Mobile bearing dislocation occurs in 1- 6% of Oxford Domed Lateral replacements. Dislocations are predominantly medial, but can occur anteriorly or posteriorly. They tend to occur when the knee is flexed. It is not clear how dislocations can be prevented. A previously described mechanical rig for assessing mobile bearing dislocation was updated so as to study dislocation with the knee in flexion. Sub-categories for the description of each type of dislocation were introduced. Dislocation was only possible when the knee was distracted. As the amount of distraction possible in the knee is variable, the risk of dislocation is related to the amount of distraction in the rig necessary for a dislocation. The type of dislocation requiring the least distraction was medial `edge' dislocation in which the edge of the bearing dislocates onto the tibial wall, which is the most common type of dislocation. The amount of distraction necessary decreased the further the bearing was from the wall and with 50% posterior overhang. Rotation of the knee did not influence the amount of distraction. In conclusion dislocation can only occur if the lateral compartment is distracted. To reduce the dislocation risk, surgeons should aim to position the femoral and tibial components so that the bearing is as close as possible to the wall without jamming against it and the tibial component should be positioned flush with the posterior tibial cortex. If, during the surgery, the mobile bearing can easily be dislocated onto the wall the surgeon should consider changing to a fixed bearing. The tibial component should also be positioned flush with the posterior tibial cortex, as if it is too far forward this may contribute to dislocation.

Wider translations and rotations in posterior-stabilised mobile-bearing total knee arthroplasty compared to fixed-bearing both implanted with mechanical alignment: a dynamic RSA study.

PURPOSE: The purpose of this study was to investigate the in vivo kinematics of the same femoral design mechanically aligned posterior-stabilised (PS) total knee arthroplasty (TKA) with either fixed-bearing (FB) or mobile-bearing (MB) inlay, implanted by the same surgeon, using model-based dynamic radiostereometric analysis (RSA). The hypothesis of the present study was that the MB design would show wider axial rotation than the FB design, without affecting the clinical outcomes. MATERIALS AND METHODS: A cohort of 21 non-randomised patients (21 DePuy Attune PS-FB) was evaluated by dynamic RSA analysis at a minimum 9-month follow-up, while performing differently demanding daily living activities such as sit to stand (STS) and deep knee lunge (DKL). Kinematic data were compared with those of a cohort of 22 patients implanted with the same prosthetic design but with MB inlay. Anterior-posterior (AP) translations, varus-valgus (VV) and internal-external (IE) rotations of the femoral component with respect to the tibial baseplate were investigated. Translation of medial and lateral compartment was analysed using the low point method according to Freeman et al. Questionnaires to calculate objective and subjective clinical scores were administered preoperatively and during follow-up visit by the same investigator. RESULTS: The FB TKA design showed lower AP translation during STS (6.8 ± 3.3 mm in FB vs 9.9 ± 3.7 mm in MB, p = 0.006*), lower VV rotation (1.9 ± 0.8° in FB vs 5.3 ± 3.3° in MB, p = 0.005) and lower IE rotation (2.8 ± 1.1° in FB vs 9.5 ± 4.3° in MB, p = 0.001) during DKL than the mobile-bearing TKA design. Posterior-stabilised FB group showed significant lower translation of the low point of the medial compartment than the MB group (p = 0.008). The percentage of patients performing medial pivot in the FB group was higher compared to MB group in the examined motor tasks. No significant differences in post-operative range of motion (117° ± 16° for FB group and 124° ± 13° for MB group) and in clinical outcomes emerged between the two cohort. CONCLUSIONS: The FB and MB designs differed in AP translations, VV rotations and IE rotations of the femoral component with respect to the tibial component in STS and DKL. Furthermore, FB cohort reported a significant higher percentage of medial pivot with respect to MB cohort. Despite this, no differences in clinical outcomes were detected between groups. Both designs showed stable kinematics and represent a viable option in primary TKA. LEVEL OF EVIDENCE: Prospective cohort study, II.

Long-term results of per-operative knee arthroscopy in confirming suitability for unicompartmental arthroplasty.

BACKGROUND: Patient selection is key to the success of medial unicondylar knee arthroplasty (UKA). Progression of arthritis is the most common indication for revision surgery. Per-operative arthroscopy is a means of directly assessing the integrity of the lateral compartment. The aim of the study is to assess the long-term survivorship of UKA performed when per-operative arthroscopy is used as a final means of deciding whether to proceed with UKA. METHODS: We used per-operative arthroscopy as a means to confirm suitability for UKA in a consecutive series of 279 Oxford medial UKA. Our series of UKA with per-operative arthroscopy (Group 1) was compared to all Oxford UKA (Group 2) and all UKA in the Australian Orthopaedic Association National Joint Replacement Registry (AOANJRR) (Group 3). RESULTS: The 14-year cumulative percentage revision (CPR) was 18.5% (95% CI 12.7, 26.4) for group 1, 19.7% (95% CI 18.8, 20.6) for group 2, and 19.2% (95% CI 18.5, 19.8) for group 3. There was no statistically significant difference in the (CPR) for the entire period when group 1 was compared to groups 2 or 3. Progression of arthritis was least in Group 1 compared to groups 2 and 3; 3.6 versus 4.4 and 4.1% respectively. Following per-operative arthroscopy 21.6% (77/356) of knees underwent a change of surgical plan from UKA to TKA. CONCLUSION: In our practice, which includes per-operative arthroscopy, we have identified a reduced risk of revision due to progression of arthritis but no difference in overall long-term implant survivorship.

Mobile-bearing prosthesis suppresses the postoperative rotational mismatch and improves patient-reported outcome measurements better than fixed-bearing prosthesis: rotational analysis by 3D measurement in total knee arthroplasty.

INTRODUCTION: It is preferable to reduce postoperative excessive rotational mismatch between the femur and tibia that causes poor clinical results following total knee arthroplasty (TKA). The aim of this study is to compare postoperative rotational mismatches and clinical outcomes with mobile- and fixed-bearing prostheses. MATERIALS AND METHODS: This study classified 190 TKAs into two groups equally by propensity score matching: mobile-bearing group (n = 95) and fixed-bearing group (n = 95). Computed tomography images of the whole leg were taken at 2 weeks postoperatively. The component alignments, rotational mismatches between the femur and tibia, and rotations among components were measured three-dimensionally. The knee range of motion, New Knee Society Score (KSS) subjective sores, and Forgotten Joint Score (FJS-12) were assessed at the final follow-up. RESULTS: Rotational mismatch between the femur and tibia was significantly less in the mobile- (- 0.8° ± 7.3°) than in the fixed-bearing (3.3° ± 8.5°, p < 0.001) group. New KSS functional activity score was significantly poorer in patients with excessive rotational mismatch (61.3 ± 21.4) than in those without it (49.5 ± 20.6, p = 0.02). Comparing mobile-bearing prosthesis, the use of fixed-bearing prosthesis was a risk factor for postoperative excessive rotational mismatch (odds ratio: 2.32, p = 0.03). CONCLUSION: When compared to a fixed-bearing prosthesis, TKA using a mobile-bearing prosthesis could suppress the postoperative rotational mismatch between the femur and tibia that causes poor subjective functional activity score. However, since this study was conducted for PS-TKA, the results might not be applicable to other models.