RESUMO
Strain can modulate bandgap and carrier mobilities in two-dimensional (2D) materials. Conventional strain-application methodologies relying on flexible/patterned/nanoindented substrates are limited by low thermal tolerance, poor tunability, and/or scalability. Here, we leverage the converse piezoelectric effect to electrically generate and control strain transfer from a piezoelectric thin film to electromechanically coupled 2D MoS2. Electrical bias polarity change across the piezo film tunes the nature of strain transferred to MoS2 from compressive (â¼0.23%) to tensile (â¼0.14%) as verified through Raman and photoluminescence spectroscopies and substantiated by density functional theory calculations. The device architecture, on silicon substrate, integrates an MoS2 field-effect transistor on a metal-piezoelectric-metal stack enabling strain modulation of transistor drain current (130×), on/off ratio (150×), and mobility (1.19×) with high precision, reversibility, and resolution. Large, tunable tensile (1056) and compressive (-1498) strain gauge factors, electrical strain modulation, and high thermal tolerance promise facile integration with silicon-based CMOS and micro-electromechanical systems.
RESUMO
Cutting force is one of the most basic signals that can reflect the information of the cutting process, so it is very necessary to study the strain elastic element of strain gauge wireless rotating dynamometers. This paper proposes a strain elastic element with a double-layer cross floating beam that can be applied to the strain gauge wireless rotating dynamometer, which can simultaneously obtain the four-component cutting force/torque information of FX, FY, FZ, and MZ. Based on the proposed strain elastic element, a compact strain gauge wireless rotating dynamometer is designed, which is composed of a tool holder, upper connection flange, strain elastic element, lower connection flange, tool base, and data acquisition and wireless transmission system. The static model of the double-layer cross floating beam on the strain elastic element is established by the segmented rigid body method, and the relationships between the material, force, structural parameters, and the strain and deformation of the floating beam are obtained. The static model is consistent with the finite element solution, which proves the rationality of the static model. Based on the established static model, the sequential quadratic programming algorithm is used to optimize the structural parameters of the double-layer cross floating beam to maximize the sensitivity of the floating beam. The overall structure of the strain elastic element is analyzed by finite element software, and the strain of the structure under simulation conditions is obtained, which provides a reference for subsequent calibration tests and circuit design. The calibration matrix and dynamic performance of the strain elastic element are obtained by the static calibration test, dynamic calibration test, and cutting test. The results show that the proposed strain elastic element has high sensitivity and low cross-sensitivity error, and can be applied to the strain gauge wireless rotating dynamometer to measure medium- and low-speed cutting forces.
RESUMO
Highly robust soft strain gauges are rapidly emerging as a promising candidate in the fields of vital signs and machine conditions monitoring. However, it is still a key challenge to achieve high-performance strain sensing in these sensors with mechanical/electrical robustness for long-term usage. The multilayer structural design of sensors enhances sensing performance while the interfacial connection of heterogeneous materials between different layers is weak. Herein, inspired by the efficient perception mechanism of scorpion slit sensilla with tough interface interconnections, the synergy of ultra-high electrical performance and mechanical robustness is successfully achieved via interface design engineering. The developed multilayer soft strain gauge (MSSG) exhibits a strain sensitivity beyond 105, a lower detection limit of 8.3 µm, a frequency resolution within 0.1 Hz, and cyclic stability over 63 000 strain cycles. Also, the tough interface improves the level of heterogeneous integration in the MSSG which allows to endure different stresses. Furthermore, an MSSG-based wireless strain monitoring system is developed that enables applications on different complex dynamic surfaces, including accurate identification of human throat activity and monitoring of rolling bearing conditions.
RESUMO
An outstanding event related to the understanding of the physics of mechanical sensors occurred and was announced in 1954, exactly seventy years ago. This event was the discovery of the piezoresistive effect, which led to the development of semiconductor strain gauges with a sensitivity much higher than that obtained before in conventional metallic strain gauges. In turn, this motivated the subsequent development of the earliest micromachined silicon devices and the corresponding MEMS devices. The science and technology related to sensors has experienced noteworthy advances in the last decades, but the piezoresistive effect is still the main physical phenomenon behind many mechanical sensors, both commercial and in research models. On this 70th anniversary, this tutorial aims to explain the operating principle, subtypes, input-output characteristics, and limitations of the three main types of mechanical sensor: strain gauges, capacitive sensors, and piezoelectric sensors. These three sensor technologies are also compared with each other, highlighting the main advantages and disadvantages of each one.
RESUMO
The strain gauge method and the digital image correlation (DIC) method are commonly employed for measuring strain in tested objects, including material specimens and structural elements. The optical method enables the assessment of 3D strain fields across the entire area of interest, achieved through cameras and advanced software. The study investigates both quasi-static strength tests and more advanced research of structures. It explores full-scale construction testing, featuring highly stressed components of new wagon designs. The paper reviews the benefits and challenges of using the DIC method to measure large-scale elements. Conducting full-scale object testing is characterized by significant complexity, often involving interactions between elements, complex loading conditions, and the influence of friction. Numerous factors affect the measurements. Therefore, to compare both methods, an initially standard shear by tensile test of CFRP composite was analyzed. The analysis of strain maps provides valuable visualization of deformation patterns occurring during construction loading. The strain gauge method was crucial for verifying the quality of the DIC measurements. The results obtained provide a detailed understanding of how the components behave, highlighting the versatility of digital image correlation technology. For strain values of 0.3% and above, a good match was obtained between optical and strain gauge measurements. Below this value, the results have less accuracy. The results obtained provide a detailed understanding of how the components behave, highlighting the versatility of digital image correlation technology. The error comparison and discussion between different measurement scenarios were conducted. The paper presents a developed methodology for measuring strain and displacement state in complex and crucial structural elements. The method can be applied to measurements of heavily loaded components used in the transportation industry; for example, in railways.
RESUMO
This paper describes the design, fabrication, integration, characterization, and demonstration of a novel flexible double-sided curvature sensor array for use in soft robotics. The paper explores the performance and potential applications of a piezoresistive sensor array consisting of four gold strain gauges on a flexible polyimide (PI) substrate arranged in a Wheatstone bridge configuration. Multiple sensor strips were arranged like the fingers of a hand. Integrating Shape Memory Alloy (SMA) foils alongside the fingers was explored to mimic a human hand-gripping motion controlled with temperature, while curvature sensor array strips measure the resulting finger shapes. Moreover, object sensing in a flexible granular material gripper was demonstrated. The sensors were embedded within Polydimethylsiloxane (PDMS) to enhance their tactile feel and adhesive properties. The findings of this study are promising for future applications, particularly in robotics and prosthetics, as the ability to accurately mimic human hand movements and reconstruct sensor surfaces paves the way for robotic hand functionality.
RESUMO
PURPOSE: Finite element analysis and an in vitro experiment were employed to investigate the loading effects of angled abutments, comparing various customized angled abutments derived from the average angle of incisors in patients with a commercial 15°∆ angled abutment, on both the implant and surrounding bone. METHODS: Four customized angled abutment models (21.9°∆, 24.15°∆, 20.22°∆, 33°∆) were developed using cone-beam computed tomography (CBCT) images of incisor inclination from various age groups of patients. 3D maxillary bone models were created from CBCT images of four individual patients. Finite element analysis and in-vitro strain gauge experiments were conducted, applying 100N or 50N of axial or oblique force, to assess the differences in stress/strain between the customized and the commercial 15°∆ angled abutments in both the implants and surrounding bone. RESULTS: Under axial loading, the stress values in the dental implant and surrounding bone were elevated due to the relatively higher angles of the customized angled abutments (21.9°∆, 24.15°∆, 20.22°∆, 33°∆) when compared to the commercial 15°∆ angled abutment; however, under oblique loading the commercial 15°∆angled abutment exhibited higher stress values in both the implant and surrounding bone. For in vitro experiment, there is no statically difference in bone strain between the customized (21.9°∆) and the commercial 15°∆ angled abutments in axial loading. Nevertheless, in oblique loading using a commercial 15°∆ angled abutment induced the higher bone strains. CONCLUSION: Customized angled abutments offer lower stress/strain under oblique loads but higher stress/strain under axial loads compared to commercial ones. Therefore, in the design and application of angled abutments, careful consideration of the occlusal load direction is paramount for achieving biomechanical success of dental implant.
RESUMO
Strain gauges, particularly for wearable sensing applications, require a high degree of stretchability, softness, sensitivity, selectivity, and linearity. They must also steer clear of challenges such as mechanical and electrical hysteresis, overshoot behavior, and slow response/recovery times. However, current strain gauges face challenges in satisfying all of these requirements at once due to the inevitable trade-offs between these properties. Here, we present an innovative method for creating strain gauges from spongy Ag foam through a steam-etching process. This method simplifies the traditional, more complex, and costly manufacturing techniques, presenting an eco-friendly alternative. Uniquely, the strain gauges crafted from this method achieve an unparalleled gauge factor greater than 8 × 103 at strains exceeding 100%, successfully meeting all required attributes without notable trade-offs. Our work includes systematic investigations that reveal the intricate structure-property-performance relationship of the spongy Ag foam with practical demonstrations in areas such as human motion monitoring and human-robot interaction. These breakthroughs pave the way for highly sensitive and selective strain gauges, showing immediate applicability across a wide range of wearable sensing applications.
RESUMO
The aim of this study was to evaluate a novel approach for measuring the polymerization shrinkage of dental resin composites - measurement of sample depth variation. This new method was compared with two testing methodologies used for assessing the polymerization shrinkage (buoyancy and strain gauge methods). Eleven commercial resin composites were investigated (EverX Posterior; EverX Flow Bulk & Dentin; G-aenial Anterior, Posterior, A'chord & Universal Injectable; Filtek One Bulk Fill & Universal Restorative; SDR + Flow and Aura Bulk Fill). In addition, filler content (wt. %), flexural modulus, and the degree of conversion were evaluated. Shrinkage values, obtained by the buoyancy method, are greater than shrinkage evaluated by the strain gauge. There are significant differences in polymerization shrinkage among the tested resin composite materials. There is a strong correlation between the newly proposed method of shrinkage measurement and the buoyancy method (r2 = 0.8; p < 0.01). There is no correlation between volumetric shrinkage measurement (depth changes and buoyancy method) and linear strain measurement. Volumetric filler amount correlates with shrinkage values evaluated by all three methods. The degree of conversion for the tested resin composites ranges from 36 % to 52 %. There are some differences (around 10 %) between the filler content (wt. %) measured by the ashing-in-air method and the data given by the manufacturers. The highest flexural modulus is 14.8 GPa and the lowest 6.6 GPa. New formulations may introduce unknown relationships between the fundamental properties of dental resin composites.
Assuntos
Gastrópodes , Animais , PolimerizaçãoRESUMO
The configuration of implant-supported prostheses is considered to influence the magnitude of stress concentrations, affecting their survival rate. The purpose of this study is to determine, through strain gauge measurements during load application, the dispersion and magnitude of strain concentrations in different implant-supported prosthesis designs. All designs matched those commonly used in posterior partially edentulous states. Three implants were inserted into an epoxy resin model (PLM-4B Vishay Measurements Group Inc., Raleigh, NC, USA), allowing for the delivery of three- and four-unit crowns in different cemented configurations. Loads were applied at vertical and oblique directions over the cast crowns in six different configurations representing various posterior partially edentulous restorations. The readings from the strain gauges adhered to the implant necks' presented data on implant strain. Prostheses including cantilevers showed the highest strain among the three-unit prostheses within the prosthetic complex, and three single units showed the least (8133 µs vs. 201 µs, respectively). Angulated load application also had a role in amplifying the strains recorded, resulting in total strains of between 3.5 and 20 times higher than during vertical loading in all configurations. It can be concluded that the configuration of implant-fixed partial prosthesis changes the loads engaging the restoration, the implant, and, probably, the supporting bone.
RESUMO
This paper describes an automated method and device to conduct the Chair Stand Tests of the Fullerton Functional Test Battery. The Fullerton Functional Test is a suite of physical tests designed to assess the physical fitness of older adults. The Chair Stand Tests, which include the Five Times Sit-to-Stand Test (5xSST) and the 30 Second Sit-to-Stand Test (30CST), are the standard for measuring lower-body strength in older adults. However, these tests are performed manually, which can be labor-intensive and prone to error. We developed a sensor-integrated chair that automatically captures the dynamic weight and distribution on the chair. The collected time series weight-sensor data is automatically uploaded for immediate determination of the sit-to-stand timing and counts, as well as providing a record for future comparison of lower-body strength progression. The automatic test administration can provide significant labor savings for medical personnel and deliver much more accurate data. Data from 10 patients showed good agreement between the manually collected and sensor-collected 30CST data (M = 0.5, SD = 1.58, 95% CI = 1.13). Additional data processing will be able to yield measurements of fatigue and balance and evaluate the mechanisms of failed standing attempts.
Assuntos
Aptidão Física , Humanos , IdosoRESUMO
During walking, sensory information is measured and monitored by sensory organs that can be found on and within various limb segments. Strain can be monitored by insect load sensors, campaniform sensilla (CS), which have components embedded within the exoskeleton. CS vary in eccentricity, size, and orientation, which can affect their sensitivity to specific strains. Directly investigating the mechanical interfaces that these sensors utilize to encode changes in load bears various obstacles, such as modeling of viscoelastic properties. To circumvent the difficulties of modeling and performing biological experiments in small insects, we developed 3-dimensional printed resin models based on high-resolution imaging of CS. Through the utilization of strain gauges and a motorized tensile tester, physiologically plausible strain can be mimicked while investigating the compression and tension forces that CS experience; here, this was performed for a field of femoral CS inDrosophila melanogaster. Different loading scenarios differentially affected CS compression and the likely neuronal activity of these sensors and elucidate population coding of stresses acting on the cuticle.
Assuntos
Dípteros , Insetos , Animais , Insetos/fisiologia , Caminhada , Sensilas/fisiologia , Extremidades/fisiologiaRESUMO
BACKGROUND: The muscle strength of the lower extremity extensors can be evaluated in the closed kinetic chain (CKC) during unilateral or bilateral conditions. Factors such as the mass and length of the muscle, joint angle, type of contraction, and gender influence the magnitude of the muscle strength. The aim of this study was to compare the isometric strength of lower extremity extensors between the different knee extension angles (KEs) as well as between bilateral and unilateral conditions. METHODS: Nineteen female students (age: 20.2 ± 0.6 years) and nineteen male students (age: 20.3 ± 0.7 years) participated in the study. The muscle strength was evaluated in CKC using the strain gauge dynamometer. The analysis included values of the maximum muscle strength normalized to body mass (MS/BM) for the six KEs of 80°, 70°, 60°, 50°, 40° and 30°. RESULTS: A significant main effect in the MS/BM values for the angle factor (p < 0.001) and condition factor (p < 0.001) was found. Moreover, there was a non-significant interaction effect between the angle factor and gender factor (p = 0.476) as well as between the condition factor and gender factor (p = 0.770). Comparisons showed significant differences in the MS/BM values between the six KEs (p < 0.001). Furthermore, significantly lower MS/BM values for bilateral conditions than unilateral conditions at the 30° KE were observed (p < 0.001). CONCLUSION: The decrease in KE by 10° significantly increased the muscle strength of the lower extremity extensors. Gender did not affect the change in MS/BM values with the change in KE and conditions. Findings also revealed significant bilateral deficit, i.e., significantly a lower summed muscle strength during bilateral conditions than unilateral conditions. The study emphasized the importance of selecting the 30° KE as the optimal angle to assess the maximum strength developed in CKC.
RESUMO
Este estudo investigou a eficácia biomecânica de infraestruturas de próteses feitas de cobalto-cromo (CoCr) e compósito de fibra de vidro (FVRC), implantadas em mandíbulas edêntulas. A distribuição de densidade foi investigada utilizando um modelo ósseo sintético, equipado com extensômetros, para simular condições anatômicas e biomecânicas humanas. Os implantes de conexão interna cone morse fabricados pela Conexão Sistemas de Próteses, Arujá, São Paulo, Brasil, têm diâmetro e comprimento de 4.0mm e 13mm, respectivamente, e os intermediários protéticos selecionados foram Micro Unit Sólidos da mesma marca para plataforma cone morse, com altura de transmucoso 2,5 mm, foram utilizados para suportar as infraestruturas de próteses híbridas. Por meio de extensometria, mediu-se a deformação óssea sob carga ao redor dos quatro implantes, comparando as performances das infraestruturas CoCr e FVRC. Os resultados revelaram informações importantes sobre a seleção de materiais para infraestruturas de próteses, com foco especiÌfico nas barras de FVRC e CoCr. Os testes "in vitro" e análises estatiÌsticas destacaram que as barras de FVRC produziram menores microdeformações em comparação com as de CoCr sob carga. Essa diferença foi estatisticamente significativa, indicando que a FVRC possui uma capacidade superior de absorver e distribuir carga de maneira mais eficiente. No entanto, ressalta-se a necessidade de estudos futuros, incluindo pesquisas clínicas, para explorar totalmente as implicações desses achados e aprimorar ainda mais as práticas de reabilitação oral com implantes (AU)
This study investigated the biomechanical effectiveness of prosthetic infrastructures made of cobalt-chromium (CoCr) and fiberglass composite (FGC), implanted in edentulous jaws. The density distribution was investigated using a synthetic bone model, equipped with strain gauges, to simulate human anatomical and biomechanical conditions. The morse cone internal connection implants manufactured by Conexão Sistemas de Próteses, Arujá, São Paulo, Brazil, have a length of 4.0mm and 13mm, respectively, and the prosthetic intermediates selected were Micro Unit Solids of the same brand for a morse cone platform, with a transmucosal height of 2.5 mm, were used to support hybrid prosthetic infrastructures. Using extensometry, bone deformation under load around the four implants was measured, comparing with the performance of the CoCr and FGC infrastructures. The results revealed important information about the selection of materials for prosthetic infrastructures, with a specific focus on FGC and CoCr bars. "In vitro" tests and statistical analyzes highlighted that FGC bars produced smaller microdeformations compared to CoCr bars under load. This difference was statistically significant, demonstrating that FGC has a superior capacity to absorb and distribute load more efficiently. However, the need for future studies, including clinical research, is highlighted to fully explore the implications of these findings and further improve oral rehabilitation practices with implants. (AU)
Assuntos
Moldes Cirúrgicos , Ligas de CromoRESUMO
As an important component connecting the upper and lower structures of a bridge, bridge bearings can reliably transfer vertical and horizontal loads to a foundation. Bearing capacity needs to be monitored during construction and maintenance. To create an intelligent pot bearing, a portable small spot welding machine is used to weld pipe-type welding strain gauges to the pot bearing to measure strain and force values. The research contents of this paper include the finite element analysis of a basin bearing, optimal arrangement of welding strain gauges, calibration testing, and temperature compensation testing of the intelligent basin bearing of the welding strain gauges. Polynomial fitting is used for the fitting and analysis of test data. The results indicate that the developed intelligent pot bearing has a high-precision force measurement function and that after temperature compensation, the measurement error is within 1.8%. The intelligent pot bearing has a low production cost, and the pipe-type welding strain gauges can be conveniently replaced. The novelty is that the bearing adopts a robust pipe-type welding strain gauge and that automatic temperature compensation is used. Therefore, the research results have excellent engineering application value.
RESUMO
In this work, the strains measured with optic fibers and recorded during tensile tests performed on carbon/epoxy composite specimens were compared to those recorded by strain gauges and by Digital Image Correlation (DIC). The work aims at investigating the sensitivity of embedded and glued optic sensors for structural health monitoring applications in comparison with strain gauges and the full field strain map of the DIC. Acrylate, polyimide optic fibers, and three strain gauge sizes are considered to compare the three techniques. Results show hard polyimide-coated sensors are more sensitive to the material pattern than soft acrylate-coated fibers, which also require extensive adhesion length. The work shows a comparable size of strain gauges and material meso-structure is also critical for properly assessing material properties. The Young's modulus computed with the three different techniques is used to define a strategy that supports the selection and the proper size of the adopted strain measuring system for structural health monitoring of composite materials.
RESUMO
The results of applications of various methods for measuring the parameters of high-speed loading using a strain gauge, a fiber Bragg grating located on a metal measuring rod and an interferometer monitoring the movement of the free boundary of the end of the rod are presented. Numerical simulation confirmed the adequacy of the description of the shock-wave process according to experimental data and showed that, with the thickness of the adhesive layer fixing the fiber Bragg grating and the strain gauge on a dimensional rod up to 100 µm, the deformation parameters of the sensors correspond to the parameters of the stress-strain state of the rod. Experimentally, a good correspondence of the results of measuring the magnitude of the relative deformation at a pulse duration of 10-100 µs using sensors of various types is shown, and an estimate of the limit values of the measured values of the deformation wave parameters is given.
RESUMO
Aim: To evaluate and compare the strain development and distribution of maxillary implant-supported complete fixed dental prosthesis (ISCFDP) with computer-aided design-computer-aided manufacturing milled PEEK BIO-HPP superstructure when placed using All-on-4 and All-on-6 situation using a strain gauge and finite element analysis (FEA). Setting and Design: This is an in vitro study to evaluate and compare the stress minimization and strain developed at implant in premolar and in two clinically simulated situation of All-on-4 and All-on -6 ISCFDP. Materials and Methods: The study involved converting a human skull into. stl format to create 3D-printed stereolithography models with a modulus of elasticity closer to bone. Implants were placed in two models (M1 nad M2) in incisor, premolar, and pterygoid regions. A fixed dental prosthesis framework was fabricated on both models, and strain gauge sensors were attached. Statistical Analysis Used: Descriptive and analytical statistics were done. The normality of data was analyzed by the Shapiro-Wilk test. Results: The results obtained were tabulated and it showed strain around the neck of ISCFDP under 100N configuration in strain gauge analysis. Stress was found more in the molar region when compared to the premolar region. This design showed that the largest stress around the neck of ISFDP under 100 N load was found more in the premolar region when compared to the molar region due to the reduction of stresses in the pterygoid region in FEA. Conclusion: In the present study, strain gauge analysis at 100 N for loading at the premolar and molar region shows the reduced strain on tilted implants in All-on-6 situation due to stress dissipation to the terminal pterygoid implant using strain gauge.
Assuntos
Implantes Dentários , Humanos , Análise de Elementos Finitos , Prótese Dentária Fixada por Implante , Análise do Estresse Dentário/métodos , Estresse MecânicoRESUMO
A high-temperature thin/thick-film strain gauge (TFSG) shows development prospects for in situ strain monitoring of hot-end components due to their small perturbations, no damage, and fast response. Direct ink writing (DIW) 3D printing is an emerging and facile approach for the rapid fabrication of TFSG. However, TFSGs prepared based on 3D printing with both high thermal stability and low temperature coefficient of resistance (TCR) over a wide temperature range remain a great challenge. Here, we report a AgPd TFSG with a glass-ceramic protective layer based on DIW. By encapsulating the AgPd sensitive layer and regulating the Pd content, the AgPd TFSG demonstrated a low TCR (191.6 ppm/°C) from 50 to 800 °C and ultrahigh stability (with a resistance drift rate of 0.14%/h at 800 °C). Meanwhile, the achieved specifications for strain detection included a strain sensing range of ±500 µÎµ, fast response time of 153 ms, gauge factor of 0.75 at 800 °C, and high durability of >8000 cyclic loading tests. The AgPd TFSG effectively monitors strain in superalloys and can be directly deposited onto cylindrical surfaces, demonstrating the scalability of the presented approach. This work provides a strategy to develop TFSGs for in situ sensing of complex curved surfaces in harsh environments.
RESUMO
Half-bridge silicon strain gauges are widely used in the fabrication of diaphragm-type high-pressure sensors, but in some applications, they suffer from low output sensitivity because of mounting position constraints. Through a special design and fabrication approach, a new half-bridge silicon strain gauge comprising one arc gauge responding to tangential strain and another linear gauge measuring radial strain was developed using Silicon-on-Glass (SiOG) substrate technology. The tangential gauge consists of grid patterns, such as the reciprocating arc of silicon piezoresistors on a thin glass substrate. When two half-bridges are connected to form a full bridge with arc-shaped gauges that respond to tangential strain, they have the advantage of providing much higher output sensitivity than a conventional half-bridge. Pressure sensors tested under pressure ranging from 0 to 50 bar at five different temperatures indicate a linear output with a typical sensitivity of approximately 16 mV/V/bar, a maximum zero shift of 0.05% FS, and a span shift of 0.03% FS. The higher output level of pressure sensing gauges will provide greater signal strength, thus maintaining a better signal-to-noise ratio than conventional pressure sensors. The offset and span shift curves are quite linear across the operating temperature range, giving the end user the advantage of using very simple algorithms for temperature compensation of offset and span shift.