Investigation of the Mechanical Properties of Thermoplastic Materials Influenced by Different Chemicals.

Objective: The quality of orthodontic forces in aligners is mainly influenced by their mechanical properties. At present, there is insufficient information on how environmental factors affect the mechanical function of aligners, and studies have shown that patients do not pay enough attention to removing aligners while eating and drinking. Therefore, in this study, we investigated the effect of different chemicals on the mechanical properties of thermoplastic materials. Methods: In this study, 175 thermoplastic samples from Easy-Vac gasket (3A Medes, Korea) were prepared, and their chemical composition, tensile strength, and hardness before and after exposure to solutions of orange juice, Cola, chlorhexidine mouthwash, and distilled water were measured. One-Way analysis of variance (ANOVA), Tamhane's test, and Tukey's test were used for statistical analysis. Results: The tensile strength of the sheets increased with continuous exposure to orange juice and chlorhexidine mouthwash, and their hardness decreased with continuous exposure to carbonated beverages. There was no change in the chemical composition of the samples after exposure to different chemicals. Conclusion: Although these changes are statistically significant, they do not have a significant effect on the result of aligner performance. Therefore, the only concern is the cariogenicity of orange juice and Cola during treatment with aligners and the administration of chlorhexidine mouthwash.

Investigation on the control of inclusions and tensile strength in Ce-treated P110-grade oil casing steel.

This research added rare Earth elements Ce to the P110-grade oil casing steel to reveal their influence on the inclusions and tensile properties. The content of cerium in the steel varied from 0 to 452 ppm. Based on the classical thermodynamic calculation, the predominance diagram of Re-containing inclusions in P110-grade steel was obtained. The evolution route of the inclusions composition with the increasing cerium content in the steel was xCaO⋅yAl2O3 → Al2O3-CeAlO3 → Ce2O3-CeAlO3 → Ce2O3-Ce2O2S → Ce2O2S, which agreed well with the thermodynamic analysis. As the cerium content at 235 ppm, the size of Ce containing inclusions has a minimal size at 2.82 µm. Suitable Ce content can modify the big-size xCaO⋅yAl2O3 inclusions into small-size Re-containing inclusions. The results demonstrate that the tensile performance of this steel can be improved as the cerium content increases from 0 to 235 ppm. However, once the cerium content exceeds 235 ppm, further increases in cerium content led to a decline in performance. The experimental results shows that the presence of large-sized Ce2O2S inclusions and the change of microstructure, will lead to the decrease in tensile performance.

A study of forecasting the Nephila clavipes silk fiber's ultimate tensile strength using machine learning strategies.

Recent advancements in biomaterial research conduct artificial intelligence for predicting diverse material properties. However, research predicting the mechanical properties of biomaterial based on amino acid sequences have been notably absent. This research pioneers the use of classification models to predict ultimate tensile strength from silk fiber amino acid sequences, employing logistic regression, support vector machines with various kernels, and a deep neural network (DNN). Remarkably, the model demonstrates a high accuracy of 0.83 during the generalization test. The study introduces an innovative approach to predicting biomaterial mechanical properties beyond traditional experimental methods. Recognizing the limitations of conventional linear prediction models, the research emphasizes the future trajectory toward DNNs that can adeptly capture non-linear relationships with high precision. Moreover, through comprehensive performance comparisons among diverse prediction models, the study offers insights into the effectiveness of specific models for predicting the mechanical properties of certain materials. In conclusion, this study serves as a pioneering contribution, laying the groundwork for future endeavors and advocating for the seamless integration of AI methodologies into materials research.

Suture Characteristics after Exposure to Amniotic Fluid from an in vitro Model of Fetal Surgery.

INTRODUCTION: Suture tensile properties have only been tested in extrauterine environments. Amniotic fluid (AF) is a complex milieu of enzymes and inflammatory factors. This study tested the mechanical properties of sutures with a variety of inherent properties, after exposure to AF from patients with conditions prompting fetal intervention. METHODS: AF was obtained from 3 patients with twin-twin transfusion syndrome (TTTS), and 3 patients with neural tube defects. Six types of 2-0 sutures were placed on 1.2 N of tension to mimic placement in vivo, and incubated in AF at 37°C (98.6°F). These included ethylene terephthalate (Ethibond), glycomer 631 (V-Loc), poliglecaprone 25 (Monocryl), poly-4-hydroxybutyrate (Monomax), polydioxanone (PDS), and polyglactin 910 (Vicryl). Failure load, stress, strain, and initial modulus were tested after 24 h of incubation and after 4 weeks, and compared with control (unincubated) sutures using t tests, Kruskal-Wallis tests, and stress-strain curves. RESULTS: Poliglecaprone 25 and polyglactin 910 dissolve more quickly in AF compared to outside the uterus, disintegrating at 4 weeks. Ethylene terephthalate and PDS experienced little change across 4 weeks of incubation. Glycomer 631 and poly-4-hydroxybutyrate exhibited interesting behavior in AF: glycomer 631 became more deformable at 24 h but later regained toughness by 4 weeks, while poly-4-hydroxybutyrate became tougher and in some cases stronger with time in AF. As a class, braided sutures act more like rigid materials, and monofilaments act like deformable plastics. CONCLUSION: These findings along with other suture characteristics such as ease of handling and availability may inform fetal intervention teams as they optimize procedures in a relatively new surgical field.

Biofilms from poly-vinyl alcohol/palmyra root sprout with Boswellia serrata, carbon dots and anthocyanin for sensing the freshness of sardine fish.

One of the main issues that customers worldwide have is food adulteration. In commercial packages, freshness cannot always be determined visually. Here, we propose sensitive films for use in food packaging that could alter colour to indicate a change in freshness. Hybrid, multifunctional, and eco-friendly films were prepared from polyvinyl alcohol/palmyra root sprout (PVA/PRS), fused with soy protein isolate carbon dot (CD), Boswellia serrata (BS), and Clitoriaternatea anthocyanin (CTE). The films showed pH sensitivity, antioxidant, and UV barrier properties. By creating hydrogen bonds between PRS and the other fillers, adding these substances makes PVA less crystallized. These interactions were verified by infrared Fourier-transform analysis. When compared to PVA, PRS films had significantly lower moisture content and swelling ratios. The UV-blocking capabilities of the films were greatly improved by the addition of CD, BS, and CTE without compromising their mechanical, thermal, or water vapor barrier properties. The composite film PVA/PRS/CD/BS/CTE exhibited a maximum tensile strength value of 69.47 ± 1.49 MPa. The CT extract provides the film with superior antioxidant properties. The colorimetric films PVA/PRS/CTE and PVA/PRS/CD/BS/CTE showed distinct pH-responsive colour-change properties as well as good colour stability. The colorimetric films were used to test the freshness of sardine fish, and they revealed unique colour changes that indicated whether the fish sample was spoiled or not.

Effect of ohmic heating on the structure and properties of flexible multilayer packaging.

Food-packaging-processing interactions define packaging materials' performance properties and product quality. This study evaluated the effect of ohmic heating (OH) processing and different food simulants on the properties of four multilayer flexible packaging materials (PETmet/PE, PETmet/PP, PET/Al/PE, and PET/Al/PA/PP). OH treatment was applied to the sealed packages containing the food simulants using a voltage gradient of 3.7 V/cm at a frequency of 20 kHz, resulting in a thermal process of at 80 °C for 1 min. The structure and performance of the different packages were then evaluated. The materials did not show changes in chemical groups nor thermal properties. However, the simulant-packaging-processing interaction resulted in changes in crystallinity, morphology, mechanical and barrier properties (water and oxygen), especially for metallized films in contact with acidic food simulants. The results indicate that although OH resulted in changes in packaging materials, these materials can be used under the conditions applied in this study.

Enhancing UHPC Tensile Performance Using Polystyrene Beads: Significant Improvements and Mechanisms.

This study investigates utilizing spherical polystyrene (PS) beads as artificial flaws to improve ultrahigh-performance concrete (UHPC) tensile performance using a uniaxial tensile test and explains the corresponding mechanisms by analyzing the internal material structure of UHPC specimens with X-ray CT scanning. With a hooked steel fiber volume fraction of 2%, three PS bead dosages were employed to study tensile behavior changes in dog-bone UHPC specimens. A 33.4% increase in ultimate tensile strength and 174.8% increase in ultimate tensile strain were recorded after adding PS beads with a volume fraction of 2%. To explain this improvement, X-ray CT scanning was utilized to investigate the post-test internal material structures of the dog-bone specimens. AVIZO software was used to analyze the CT information. The CT results revealed that PS beads could not only serve as the artificial flaws to increase the cracking behavior of the matrix of UHPC but also significantly optimize the fiber orientation. The PS beads could serve as stirrers during the mixing process to distribute fiber more uniformly. The test results indicate a relationship between fiber orientation and UHPC tensile strength.

Investigation on the Preparation and Performances of Epoxy-Modified Asphalt Binder and Its Mixtures.

Epoxy-modified asphalt binder has been widely used in steel deck pavement due to its excellent properties and it is a potential candidate for long life pavements. However, its short reserve time limits its widespread application in pavement engineering. Therefore, this work developed a novel epoxy-modified asphalt binder composed of a laboratory-made curing agent as a solution. Firstly, optimization of preparation temperature of this new material was studied to balance the requirements of enough construction time and the material strength and elongation. The epoxy-modified asphalt binder, prepared at the optimal temperature of 140 °C, had a reserve time exceeding 120 min, whereas the tensile strength and the elongation at failure were 2.22 MPa and 216%, respectively, which satisfied the standard requirements of paving epoxy material well. Secondly, the asphalt mixture property tests demonstrate excellent high-temperature rutting resistance, water stability and low-temperature anti-cracking ability. Additionally, the compatibility and colloidal stability of this epoxy-modified asphalt binder were analyzed in terms of microphase structure. The uniform microphase distribution of this binder showed by the laser confocal microscope observation in both short-term aging case and long-term aging case, indicates the great compatibility between asphalt and epoxy resin during paving process and service life. Furthermore, fatigue tests were conducted to evaluate the long-term durability. The fatigue life of epoxy-modified asphalt mixtures increased by 435%, 427%, 342%, and 276% under the stress ratios of 0.3, 0.4, 0.5, and 0.6, respectively, compared to those of SBS-modified asphalt mixtures. All these results indicate that the new epoxy-modified asphalt material is promising for applications in pavement engineering, especially suitable for long-life road pavement.

Goldene: An Anisotropic Metallic Monolayer with Remarkable Stability and Rigidity and Low Lattice Thermal Conductivity.

In a recent breakthrough in the field of two-dimensional (2D) nanomaterials, the first synthesis of a single-atom-thick gold lattice of goldene has been reported through an innovative wet chemical removal of Ti3C2 from the layered Ti3AuC2. Inspired by this advancement, in this communication and for the first time, a comprehensive first-principles investigation using a combination of density functional theory (DFT) and machine learning interatomic potential (MLIP) calculations has been conducted to delve into the stability, electronic, mechanical and thermal properties of the single-layer and free-standing goldene. The presented results confirm thermal stability at 700 K as well as remarkable dynamical stability of the stress-free and strained goldene monolayer. At the ground state, the elastic modulus and tensile strength of the goldene monolayer are predicted to be over 226 and 12 GPa, respectively. Through validated MLIP-based molecular dynamics calculations, it is found that at room temperature, the goldene nanosheet can exhibit anisotropic tensile strength over 9 GPa and a low lattice thermal conductivity around 10 ± 2 W/(m.K), respectively. We finally show that the native metallic nature of the goldene monolayer stays intact under large tensile strains. The combined insights from DFT and MLIP-based results provide a comprehensive understanding of the stability, mechanical, thermal and electronic properties of goldene nanosheets.

Effects of Calcination Temperature on the Synthesis of One-Pot Sol-Gelled Barium Titanate Powder and Its Performance as an Endodontic Radiopacifier.

Barium titanate (BaTiO3, BTO), conventionally used for dielectric and ferroelectric applications, has been assessed for biomedical applications, such as its utilization as a radiopacifier in mineral trioxide aggregates (MTA) for endodontic treatment. In the present study, BTO powders were prepared using the sol-gel process, followed by calcination at 400-1100 °C. The X-ray diffraction technique was then used to examine the as-prepared powders to elucidate the effect of calcination on the phase composition and crystalline size of BTO. Calcined BTO powders were then used as radiopacifiers for MTA. MTA-like cements were investigated to determine the optimal calcination temperature based on the radiopacity and diametral tensile strength (DTS). The experimental results showed that the formation of BTO phase was observed after calcination at temperatures of 600 °C and above. The calcined powders were a mixture of BaTiO3 phase with residual BaCO3 and/or Ba2TiO4 phases. The performance of MTA-like cements with BTO addition increased with increasing calcination temperature up to 1000 °C. The radiopacity, however, decreased after 7 days of simulated oral environmental storage, whereas an increase in DTS was observed. Optimal MTA-like cement was obtained by adding 40 wt.% 1000 °C-calcined BTO powder, with its resulting radiopacity and DTS at 4.83 ± 0.61 mmAl and 2.86 ± 0.33 MPa, respectively. After 7 days, the radiopacity decreased slightly to 4.69 ± 0.51 mmAl, accompanied by an increase in DTS to 3.13 ± 0.70 MPa. The optimal cement was biocompatible and verified using MG 63 and L929 cell lines, which exhibited cell viability higher than 95%.

Remarkably high tensile strength and lattice thermal conductivity in wide band gap oxidized holey graphene C2O nanosheet.

Recently, the synthesis of oxidized holey graphene with the chemical formula C2O has been reported (J. Am. Chem. Soc. 2024, 146, 4532). We herein employed a combination of density functional theory (DFT) and machine learning interatomic potential (MLIP) calculations to investigate the electronic, optical, mechanical and thermal properties of the C2O monolayer, and compared our findings with those of its C2N counterpart. Our analysis shows that while the C2N monolayer exhibits delocalized π-conjugation and shows a 2.47 eV direct-gap semiconducting behavior, the C2O counterpart exhibits an indirect gap of 3.47 eV. We found that while the C2N monolayer exhibits strong absorption in the visible spectrum, the initial absorption peaks in the C2O lattice occur at around 5 eV, falling within the UV spectrum. Notably, we found that the C2O nanosheet presents significantly higher tensile strength compared to its C2N counterpart. MLIP-based calculations show that at room temperature, the C2O nanosheet can exhibit remarkably high tensile strength and lattice thermal conductivity of 42 GPa and 129 W/mK, respectively. The combined insights from DFT and MLIP-based results provide a comprehensive understanding of the electronic and optical properties of C2O nanosheets, suggesting them as mechanically robust and highly thermally conductive wide bandgap semiconductors.

Microhardness and Tensile Strength Analysis of SS316L/CuCrZr Interface by Laser Powder Bed Fusion.

Metallic joints within tokamak devices necessitate high interface hardness and superior bonding properties. However, conventional manufacturing techniques, specifically the hot isostatic pressing (HIP) diffusion joining process, encounter challenges, including the degradation of the SS316L/CuCrZr interface and CuCrZr hardness. To address this, we explore the potential of laser powder bed fusion (LPBF) technology. To assess its viability, we fabricated 54 SS316L/CuCrZr samples and systematically investigated the impact of varied process parameters on the microhardness and tensile strength of the dissimilar metal interfaces. Through comprehensive analysis, integrating scanning electron microscopy (SEM) imagery, we elucidated the mechanisms underlying mechanical property alterations. Notably, within a laser volumetric energy density range of 60 J/mm3 to 90 J/mm3, we achieved elevated interface hardness (around 150 HV) and commendable bonding quality. Comparative analysis against traditional methods revealed a substantial enhancement of 30% to 40% in interface hardness with additive manufacturing, effectively mitigating CuCrZr hardness degradation.

Evaluation of Major Physical and Mechanical Properties of Trembling Aspen Lumber.

Trembling aspen (Populus tremuloides) is one of the major species within Populus, a predominant genus of hardwoods in North America. However, its utilization has been limited to pulp and paper or wood-based composite boards. This study aimed at evaluating the major physical and mechanical properties of trembling aspen lumber, with an ultimate objective of using this species to produce engineered wood products (EWPs). The testing materials consisted of 2 × 4 (38 mm × 89 mm) trembling aspen lumber pieces in lengths of 8, 10, and 12 feet (2.44, 3.05, and 3.66 m) with two visual grades, select structural (SS) and No. 2. Machine Stress-Rated (MSR), and longitudinal stress wave (LSW), edgewise third-point bending (EWB), and axial tension tests were conducted on the lumber. It was found that, (1) by increasing the maximum knot size by a half-inch from one-quarter inch, the minimum modulus of elasticity (MOE) measured using the MSR, the mean, and the fifth-percentile ultimate tensile strength (UTS) decreased by about 8.8%, 20.1%, and 29.8%, respectively. (2) Approximately 44% of the trembling aspen lumber met the 1450f-1.3E grade for MSR lumber, and 62% qualified for the 1200f-1.2E grade. (3) There was a great potential for manufacturing cross-laminated timber (CLT) of grade E3, with a rejection rate of about 29%. (4) The mean UTS and MOE values of the SS-grade trembling aspen lumber were 22.88 MPa and 9519 MPa, respectively, being 25.5% and 11.3% lower than that of Spruce-Pine-Fir (S-P-F) lumber. The fifth-percentile UTS and MOE values were 11.57 MPa and 7404 MPa, respectively, marking a decrease of 13.3% and 1.5% compared to the S-P-F lumber. (5) The oven-dried specific gravity (SG) of the trembling aspen wood was 0.40, which was about 3.5% larger than the value provided in the Wood Handbook.

Synthesis and Characterization of Sol-Gelled Barium Zirconate as Novel MTA Radiopacifiers.

Barium zirconate (BaZrO3, BZO), which exhibits superior mechanical, thermal, and chemical stability, has been widely used in many applications. In dentistry, BZO is used as a radiopacifier in mineral trioxide aggregates (MTAs) for endodontic filling applications. In the present study, BZO was prepared using the sol-gel process, followed by calcination at 700-1000 °C. The calcined BZO powders were investigated using X-ray diffraction and scanning electron microscopy. Thereafter, MTA-like cements with the addition of calcined BZO powder were evaluated to determine the optimal composition based on radiopacity, diametral tensile strength (DTS), and setting times. The experimental results showed that calcined BZO exhibited a majority BZO phase with minor zirconia crystals. The crystallinity, the percentage, and the average crystalline size of BZO increased with the increasing calcination temperature. The optimal MTA-like cement was obtained by adding 20% of the 700 °C-calcined BZO powder. The initial and final setting times were 25 and 32 min, respectively. They were significantly shorter than those (70 and 56 min, respectively) prepared with commercial BZO powder. It exhibited a radiopacity of 3.60 ± 0.22 mmAl and a DTS of 3.02 ± 0.18 MPa. After 28 days of simulated oral environment storage, the radiopacity and DTS decreased to 3.36 ± 0.53 mmAl and 2.84 ± 0.27 MPa, respectively. This suggests that 700 °C-calcined BZO powder has potential as a novel radiopacifier for MTAs.

Mechanical Properties of Twisted Cellulose Nanofiber-Reinforced Silk Yarns.

Silk has recently attracted considerable interest owing to its versatile properties as a natural fiber, especially in the medical sector. However, the mechanical properties of silk limit its potential applications. In our earlier work, the mechanical performance of silk filaments was enhanced owing to the insertion of cellulose nanofibers (CNFs). Nevertheless, silk filaments must be assembled and twisted to form a continuous yarn. In this study, the mechanical properties of CNF-reinforced silk yarns were evaluated to determine the optimal yarn structure. The evolution of the Young's modulus, ultimate tensile strength, toughness, and elongation at break was assessed as a function of the twist level in comparison with regular silk. The results demonstrated that the most favorable compromise of the mechanical properties was obtained at 1000 twists per meter.

Self-Healing Polyurethane Elastomers with Superior Tensile Strength and Elastic Recovery Based on Dynamic Oxime-Carbamate and Hydrogen Bond Interactions.

The preparation of self-healing polyurethane elastomers (PUEs) incorporating dynamic bonds is of considerable practical significance. However, developing a PUE with outstanding mechanical properties and high self-healing efficiency poses a significant challenge. Herein, this work has successfully developed a series of self-healing PUEs with various outstanding properties through rational molecular design. These PUEs incorporate m-xylylene diisocyanate and reversible dimethylglyoxime as hard segment, along with polytetramethylene ether glycol as soft segment. A significant amount of dynamic oxime-carbamate and hydrogen bonds are formed in hard segment. The microphase separated structure of the PUEs enables them to be colorless with a transparency of >90%. Owing to the chemical composition and multiple dynamic interactions, the PUEs are endowed with ultra-high tensile strength of 34.5 MPa, satisfactory toughness of 53.9 MJ m-3, and great elastic recovery both at low and high strains. The movement of polymer molecular chains and the dynamic reversible interactions render a self-healing efficiency of 101% at 70 °C. In addition, this self-healing polyurethane could still maintain high mechanical properties after recycling. This study provides a design strategy for the preparation of a comprehensive polyurethane with superior overall performance, which holds wide application prospects in the fields of flexible displays and solar cells.

Evaluation of binders in twin-screw wet granulation - Optimization of tabletability.

The influence of hydroxypropyl cellulose type (HPC-SSL SFP, HPC-SSL), concentration (2 %, 3.5 %, 5 %) and filler (lactose, calcium hydrogen phosphate (DCP)/microcrystalline cellulose (MCC)) on twin-screw wet granulation and subsequent tableting was studied. The aim was to identify the formulation of the highest tabletability which still fulfills the requirements of the disintegration. Lactose combined with 5 % binder enabled a higher tabletability and a faster disintegration than DCP/MCC. It was found that tabletability of lactose formulations can be increased by higher binder concentration and higher compression pressure while tabletability of DCP/MCC formulations can be only increased by higher compression pressure. It was observed that batches containing DCP/MCC failed the disintegration test, if the highest binder concentration and the highest compression pressure were used. To ensure a fast disintegration, the compression pressure or at least the binder concentration had to be low. Changing the disintegrant and its localization improved the DCP/MCC formulation, resulting in faster disintegration than lactose tablets. However, it also resulted in a lower tabletability. In this study best tablets were achieved with 3.5 % or 5 % binder and lactose as filler. These tablets presented the highest tabletability but still disintegrated in less than 500 s.

A modified Kushner-Moore approach to characterising small-scale blender performance impact on tablet compaction.

Continuous Direct Compaction (CDC) has emerged as a promising route towards producing solid dosage forms while reducing material, development time and energy consumption. Understanding the response of powder processing unit operations, especially blenders, is crucial. There is a substantial body of work around how lubrication via batch blender operation affects tablet critical quality attributes such as hardness and tensile strength. But, aside from being batch operations, the design of these blenders is such that they operate with low-shear, low-intensity mixing at Froude number values significantly below 0.4 (Froude number Fr being the dimensionless ratio of inertial to gravitational forces). The present work explores the performance of a mini-blender which has a fundamentally different mode of operation (static vessel with rotating blades around a mixing shaft as opposed to rotating vessel with no mixing shaft). This difference allows a substantially wider operating range in terms of speed and shear (and Fr values). The present work evaluates how its performance compares to other blenders studied in the literature. Tablet compaction data from blends produced at various intensities and regimes of mixing in the mini-blender follow a common trajectory. Model equations from literature are suitably modified by inclusion of the Froude number Fr, but only for situations where the Froude number was sufficiently high (1 < Fr). The results suggest that although a similar lubrication extent plateau is eventually reached it is the intensity of mixing (i.e. captured using the Froude number as a surrogate) which is important for the lubrication dynamics in the mini-blender, next to the number of revolutions. The degree of fill or headspace, on the other hand, is only crucial to the performance of common batch blenders. Testing using alternative formulations shows the same common trend across mixing intensities, suggesting the validity of the approach to capture lubrication dynamics for this system.

Hybrid Metal Oxide (Ag-ZnO) Impregnated Biocomposite in the Development of an Eco-Friendly Sustainable Film.

Nanotechnology offers an innovative application as an eco-friendly food packaging film fabricated along with a degradable active mixture (AM). The AM is an assortment of alloyed metal oxide nanoparticles (Ag-ZnO), citron powder (AA), and Curcuma peel powder (CPP). Alloyed nanoparticles (NPs) were observed to exhibit a hexagonal structure from the experimental X-ray diffraction. Compositional and morphological study of the NPs (22.69 nm) and AM (32 nm) was done using energy-dispersive X-ray spectroscopy (EDX), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and ζ- potential was observed to be -14.7 mV, indicating the stability of NPs. The prepared film was observed to be more effective with antibacterial analysis against Escherichia coli, exhibiting 72% of inhibition and antioxidant activity with IC50: 51.56% using the 2,2 diphenyl-1-picrylhydrazyl (DPPH) assay. Film 1, Film 2, Film 3, and Film 4 were fabricated with the AM and observed to be perfectly encapsulated by PVA using XRD. FESEM images of the film exhibit the aggregation of NPs with biocomposites in perfect distribution. The mechanical properties such as Young's modulus, elongation at break, tensile strength, and ultimate tensile strength (UTS- 5.37 MPa) were experimented for the films. The degradation rate was observed to be 6.12% for film 1 using the soil burial method. The study emphasizes that NPs along with biocomposite upgrade the sustainability of the packaging film with improved mechanical and physicochemical properties. The synthesized film with biomaterials could be used as a "green" food package to store fruits, vegetables, and sweets in the food industry.

Biodegradable, UV-blocking, and antioxidant films from alkali-digested lignocellulosic residue fibers of switchgrass.

The development of bio-friendly materials to replace single-use plastics is urgently needed. In this regard, cellulosic material from plants is a promising alternative. However, due to the risk of forest depletion, agricultural biomass stands out as a favorable choice. Toward this end, switchgrass, an underutilized grass, presents itself as a viable source of lignocellulose that can be turned into a bio-friendly material. Herein, lignocellulosic residue from switchgrass has been extracted using two different concentrations of NaOH (20% and 50% w/v), solubilized in aqueous ZnCl2 solution, and crosslinked with CaCl2 (200, 300, 400, and 500 mM) to prepare biodegradable films. The color, thickness and moisture, water solubility, water absorption, water vapor permeability, tensile strength and elongation, biodegradation, UV transmittance, and antioxidant activity of films have been studied. The films possess a high tensile strength of 14.7 MPa and elongation of 4.7%. They block UVB-radiation and hold antioxidant properties. They display good water vapor permeability of 1.410-1.6 × 10-11 gm-1s-1Pa-1 and lose over 80% of their weight at 30% soil moisture within 40 days. An increase in the CaCl2 amount decreased the water vapor permeability, elongation, UV transmittance, and biodegradation but increased the transparency, tensile strength and antioxidant property. Overall, films of alkali-digested lignocellulosic residue of switchgrass showed excellent potential to be used against lightweight plastics and support the circular economy.