Kinetic modeling of the photocatalytic degradation of acetaminophen and its main transformation products.

In this study, a kinetic model of the heterogeneous photocatalytic degradation of acetaminophen and its main transformation products is presented. Kinetic photocatalytic modeling and photon absorption rate modeling were included. Monte Carlo method was used to model the photon absorption process. Experiments were carried out in a reactor operated in batch mode and TiO2 nanotubes were used as photocatalyst irradiated with 254 nm UVC. Kinetic parameters were estimated from the experiments data by applying a non-linear regression procedure. Intrinsic expressions to the kinetics of acetaminophen degradation and its main transformation products were derived. Model, kinetics and photon absorption formulations and parameters proved to be affordable for describing the photocatalytic degradation of acetaminophen, but improvements should be done for better description of formation and oxidation kinetics of main transformation products. The model should be tested with other pharmaceuticals and emergent pollutants to calibrate it and evaluate its applicability in a wide range of compounds.

Ketorolac removal through photoelectrocatalysis using TiO2 nanotubes in water system.

Ketorolac, a highly persistent NSAID of environmental concern, was significantly removed from water (80% removal) through photoelectrocatalysis where titanium dioxide nanotubes prepared by Ti foil electrochemical anodization at 30 V were used as photoanodes. Fifteen milligrams per liter of ketorolac solutions in a 0.05 M Na2SO4 aqueous medium was subjected to irradiation from a 365-nm light with an intensity of 1 mWcm-2 and under an applied potential of 1.3 V (vs. Hg/Hg2SO4/sat.K2SO4) at pH 6.0. When each process (photo and electrocatalysis) was carried out separately, less than 20% drug removal was achieved as monitored through UV-vis spectrophotometry. Through scavenging experiments, direct oxidation on the photogenerated holes and oxidation by hydroxyl radical formation were found to play a key role on ketorolac's degradation. Chemical oxygen demand (COD) analyses also showed a significant COD decreased (68%) since the initial COD value was 31.3 mg O2/L and the final COD value was 10.1 mg O2/L. A 48% mineralization was also achieved, as shown by total organic carbon (TOC) analyses. These results showed that electrodes based on titania nanotubes are a promising alternative material for simultaneous photocatalytic and electrocatalytic processes in water remediation.

XPS Characterization of TiO2 Nanotubes Growth on the Surface of the Ti15Zr15Mo Alloy for Biomedical Applications.

Ti15Zr15Mo (TMZ alloy) has been studied in recent years for biomedical applications, mainly due to phase beta formation. From the surface modification, it is possible to associate the volume and surface properties with a better biomedical response. This study aimed to evaluate the possibility of using anodization to obtain TiO2 nanotubes due to the presence of valve-type metal (Zr) in their composition. X-ray photoelectron spectroscopy (XPS) was performed to determine the surface chemical composition in both after-processing conditions (passive layer) and after-processing plus anodization (TiO2 nanotube growth). The anodization resulted in nanotubes with diameters and thicknesses of 126 ± 35 and 1294 ± 193 nm, respectively, and predominated anatase phase. Compared to the passive layer of titanium, which is less than ~10 nm, the oxide layer formed was continuous and thicker. High-resolution spectra revealed that the oxide layer of the element alloys contained different oxidation states. The major phase in all depths for the nanotube samples was TiO2. While the stable form of each oxide was found to predominate on the surface, the inner part of the oxide layer consisted of suboxides and metallic forms. This composition included different oxidation states of the substrate elements Ti, Zr, and Mo.

Selective Photooxidation of Valencene and Thymol with Nano-TiO2 and O2 as Oxidant.

The selective photocatalytic oxidation with O2 as oxidant of valencene and thymol was evaluated using nanostructured TiO2 under UV-Vis radiation at atmospheric conditions. The effect of the morphology and optical properties of TiO2 nanotubes and aminate nanoparticles was studied. Different scavengers were used to detect the presence of positive holes (h+), electrons (e-), hydroxyl radicals (•OH), and the superoxide radical anion (O2-) during the photooxidation reaction. Superoxide anion radical is the main oxidizing specie formed, which is responsible for the selective formation of nootkatone and thymoquinone using aminated TiO2 nanoparticles under 400 nm radiation.

Photocatalytic and mechanical properties of immobilized nanotubular TiO2 photocatalysts obtained by anodic oxidation: a novel combined analysis.

The photocatalytic and mechanical performance of TiO2 nanotubular coatings obtained by anodic oxidation of commercial titanium, using an NH4F and 3.5% v/v water in ethylene glycol solution as electrolyte was investigated. After the anodization, the coatings were thermally treated at 450 °C for 2 h. The effects of the anodizing voltage (40-80 V) and NH4F concentration (0.06, 0.15, 0.27 M) on the formation of the nanotube arrays were evaluated. Nanotube diameters (57 to 114 nm), wall thicknesses (4 to 13 nm), and lengths (5 to 17 µm) increased with the anodizing voltage and the NH4F concentration. The photocatalysts were characterized by scanning electron microscopy, glancing incidence X-ray diffraction, and UV-Vis diffuse reflectance spectroscopy. The mechanical properties of the photocatalysts were determined: adhesion using the tape test (ASTM D3359) and erosion resistance through a 3 h accelerated test. The photocatalytic activity of the nanotubes under UV irradiation was evaluated using hexavalent chromium (Cr(VI)) in the presence of ethylenediaminetetraacetic acid (EDTA), using a 1.25 EDTA/Cr(VI) molar ratio solution at pH 2. A complete Cr(VI) transformation after 3 h of irradiation was obtained for all samples, with a better performance than that of an immobilized P25 sample. The photocatalyst obtained with 0.27 M NH4F at 40 V presented a good behavior in adherence and erosion resistance, together with a very good photocatalytic activity. This novel analysis, combining photocatalytic and mechanical tests, proved that the new TiO2 nanotubular coatings could be successfully used as immobilized photocatalysts in photoreactors for water treatment.

Electrochemical degradation of amoxicillin in acidic aqueous medium using TiO2-based electrodes modified by oxides of transition metals.

One of the most widely used antibiotics is amoxicillin (AMX), which is the most widely used in humans and animals, but it is discharged metabolically due to its indigestibility. Conventional biological and physicochemical methods for removing AMX from water are not enough to mineralize it; it is only concentrated and transferred to produce new residues that require further processing to remove the new residues. In this research, naked and modified surfaces with TiO2 nanotubes (TiO2,nt) electrophoretically modified with PbO2, IrO2, RuO2, and Ta2O5 were used to evaluate their efficiency in the electrochemical degradation of AMX in acid media (0.1 mol L-1 H2SO4). After their comparison, Pb-Ta 50:50|TiO2,nt|Ti showed the highest removal efficiency of AMX (44.71%) with the lowest specific energy consumption (8.69 ± 0.78 kWh Kg COD-1) and the average instant current efficiency of 26.67 ± 9.19%, in comparison with the others naked and modified surfaces of TiO2,nt∣Ti.

The Deposition of a Lectin from Oreochromis niloticus on the Surface of Titanium Dioxide Nanotubes Improved the Cell Adhesion, Proliferation, and Osteogenic Activity of Osteoblast-like Cells.

Titanium and its alloys are used as biomaterials for medical and dental applications, due to their mechanical and physical properties. Surface modifications of titanium with bioactive molecules can increase the osseointegration by improving the interface between the bone and implant. In this work, titanium dioxide nanotubes (TiO2NTs) were functionalized with a lectin from the plasma of the fish Oreochromis niloticus aiming to favor the adhesion and proliferation of osteoblast-like cells, improving its biocompatibility. The TiO2NTs were obtained by anodization of titanium and annealed at 400 °C for 3 h. The resulting TiO2NTs were characterized by high-resolution scanning electron microscopy. The successful incorporation of OniL on the surface of TiO2NTs, by spin coating, was demonstrated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIE), and attenuated total reflection-Fourier transform infrared spectrum (ATR-FTIR). Our results showed that TiO2NTs were successfully synthesized in a regular and well-distributed way. The modification of TiO2NTs with OniL favored adhesion, proliferation, and the osteogenic activity of osteoblast-like cells, suggesting its use to improve the quality and biocompatibility of titanium-based biomaterials.

TiO2NTs bio-inspired coatings: revisiting electrochemical, morphological, structural, and mechanical properties.

By altering some synthesis variables, the morphology and structural properties of anodic TiO2nanotube arrays (TiO2NTs) can be tailored to a specific application. This study aims to investigate the effect of electrolyte-containing ions from human plasma and annealing temperature on structural, morphological, and mechanical parameters of TiO2NTs films, targeting its potential biomedical applications. Bio-inspired TiO2NTs were grown from Ticpand its Ti6Al4V alloy by potentiostatic anodization in the recently developed SBF-based electrolyte, maintained at 10 °C and 40 °C. The thermal investigation was performed by TGA/DSC and used to define the phase transition temperatures used for annealing (450 °C and 650 °C). Morphological and structural parameters were evaluated by FE-SEM, XRD, contact angle measurements, and nanoindentation. Results show that self-organized as-formed TiO2NTs were grown under all synthesis conditions with different wettability profiles for each substrate group. At 450 °C annealing temperature, the beginning of nanostructures collapse starts, becoming evident at 650 °C. The nanoindentation characterization reveals that both electrolyte and thermal annealing exhibited low effects on the hardness and Young's modulus. The tailoring of specific properties by different synthesis conditions could allow the individualization of treatments and better performancein vivo.

Comparison of Different Synthetic Routes of Hybrid Hematite-TiO2 Nanotubes-Based Electrodes.

Nowadays, green hydrogen is an important niche of interest in which the search for a suitable composite material is indispensable. In this sense, titanium oxide nanotubes (TiO2 nanotube, TNTs) were prepared from double anodic oxidation of Ti foil in ethylene glycol electrolyte. The morphology of the nanotubes was characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Once characterized, nanotubes were used as templates for the deposition of hematite. The use of three synthetic procedures was assayed: Chemical Vapor Deposition (CVD), Successive Ionic Layer Adsorption and Reaction (SILAR), and electrochemical synthesis. In the first case, CVD, the deposition of hematite onto TiO2 yielded an uncovered substrate with the oxide and a negative shift of the flat band potential. On the other hand, the SILAR method yielded a considerable amount of hematite on the surface of nanotubes, leading to an obstruction of the tubes in most cases. Finally, with the electrochemical synthesis, the composite material obtained showed great control of the deposition, including the inner surface of the TNT. In addition, the impedance characterization showed a negative shift, indicating the changes of the interface electrode-electrolyte due to the modification with hematite. Finally, the screening of the methods showed the electrochemical synthesis as the best protocol for the desired material.

A promising technology based on photoelectrocatalysis against Mycobacterium tuberculosis in water disinfection.

Mycobacterium tuberculosis is highly infectious, persistent and has been detected in more than one quarter of the world's population. It is notoriously resistant to sterilization and disinfection procedures, largely due to an unusual hydrophobic cell wall and effective defense mechanisms against oxidative stress. This work shows an effective method to reduce M. tuberculosis quantity in water by using Ti/TiO2 nanotubes electrodes bare and coated with Ag nanoparticles by using photoelectrocatalytic oxidation process. The results have indicated 99.999% of inactivation of a solution spiked with standard and resistant strains of 1×104 CFU mL-1 M. tuberculosis after 5 min of treatment at Ti/TiO2 photoanode in 0.05 mol L-1 Na2SO4 (pH 6) under applied potential of + 1.5 V versus Ag/AgCl and UV irradiation. The mycobacteria degradation was monitored by dissolved total organic carbon (TOC) removal, carbohydrate release, chromatography coupled to mass spectroscopy measurements and it is slightly superior to photocatalysis and photolysis processes. All the results corroborated with the complete inactivation and degradation of the byproducts generated during cell lysis.

Effect of surface characteristics on the antibacterial properties of titanium dioxide nanotubes produced in aqueous electrolytes with carboxymethyl cellulose.

Nanotubular structures were produced on a commercially pure titanium surface by anodization in an aqueous electrolyte that contained carboxymethyl cellulose and sodium fluoride. The internal diameters obtained were about 100, 48, and 9.5 nm, respectively. Several heat treatments at 200, 350, and 600°C were made to produce nanotubes with different titanium dioxide polymorphs (anatase, rutile). All tested surfaces were superhydrophilic, this behavior was maintained after at least 30 days, regardless of the heat treatment. Although in previous works the nanotube features effect on the bacteria behavior had been studied; this item still unclear. For the best of our knowledge, the effect of small internal diameters (about 10 nm) with and without heat treatment and with and without ultraviolet (UV) irradiation on the bacteria strains comportment has not been reported. From our results, both the internal diameter and the postanodized treatments have an effect on the bacteria strains comportment. All nanotubular coatings UV treated and heat treated at 350 and 600°C; despite they have different inner diameters, inhibit the bacteria growth of both Staphylococcus aureus and Pseudomonas aeruginosa strains. The nanotubular coatings obtained at 20 V and heat treated at 350°C produced the lower bacteria adhesion against both strains evaluated.

Extension of hydrophilicity stability by reactive plasma treatment and wet storage on TiO2 nanotube surfaces for biomedical implant applications.

Micro and nanoscale changes allow the optimization of physico-chemical properties of titanium implant surfaces. Recently UV and plasma treatments have allowed surface hydrophilicity to take increased prominence; however, this beneficial effect is short-lived. The aim of this study is to investigate methodologies post-anodizing treatment to generate and maintain high surface hydrophilicity along with high biocompatibility. Anodized surfaces were characterized regarding physical-chemical properties. Then, surface wettability with nanomorphology was evaluated at different times and with distinct post-treatments: as deposited, with a reactive plasma and UV-light post-treatment, stored in air or deionized (DI) water. Adhesion, alkaline phosphatase (ALP) activity and bone cell viability tests were executed after the incremental treatments. The anodizing process generated a surface with TiO2 nanotubes morphology and micro-roughness. Plasma-treated surfaces resulted in the most hydrophilic samples and this property was maintained for a longer period when those were stored in DI water (angle variation of 7° to 12° in 21 days). Furthermore, plasma post-treatment changed the titanium surface crystalline phase from amorphous to anatase. Anodized surfaces modified by reactive plasma and stored in DI water suggest better hydrophilicity stability, biocompatibility, ALP activity and achievement of crystalline phase alteration, indicating future potential use on biomedical implants.

Photoelectrocatalytic degradation of 17α-ethinylestradiol and estrone under UV and visible light using nanotubular oxide arrays grown on Ti-0.5wt%W.

Environmental concern with emerging contaminants has increased in recent years, especially with regard to endocrine-disrupting compounds (EDCs), among them hormones. Conventional water treatment processes have been shown to be ineffective in removing these compounds from water and sewage, while heterogeneous photocatalysis has been demonstrated to be a promising technique. However, the catalytic efficiency is strongly related to the choice of the photocatalyst material. In order to obtain a fast and efficient degradation of these endocrine disruptors, nanotubes grown on Ti-0.5wt%W alloy (NT/Ti-0.5W) were used in photocatalytic (PC) and photoelectrocatalytic (PEC) processes for the degradation of estrone (E1) and 17α-ethinylestradiol (EE2) under irradiation with ultraviolet (UV) and visible light. The NT/Ti-0.5W catalysts were synthesized by an anodization process, followed by thermal treatment at 450 °C. Raman, X-ray diffraction and diffuse reflectance spectroscopic analyses indicated that the tungsten doping process had modified the nanotubular TiO2. The doped samples exhibited superior photoactivity compared to un-doped samples and other semiconductors under UV and visible irradiation due to a reduction in the rate of recombination of photogenerated charges and the displacement of the flat-band potential to more negative values. Higher values of the degradation rate constant were found for both hormones in the PEC process using NT/Ti-0.5W under UV radiation; the percentage removals of EE2 and E1 were 66% and 53.4%, respectively, after only 2 min of treatment. With visible light, 1.8 min and 4.6 h were required for the removal of 50% of E1 and EE2, respectively. The degradation of E1 could be fit with a zero-order kinetic model, while a first-order kinetic model was required for EE2 degradation. Degradation routes were suggested for E1 and EE2. The results demonstrate that the combined use of NT/Ti-0.5W and the PEC process provides excellent performance for the degradation of emerging contaminants in wastewater when compared to a NT/TiO2 electrode.

Characterization and comparison of Ti/TiO2-NT/SnO2-SbBi, Ti/SnO2-SbBi and BDD anode for the removal of persistent iodinated contrast media (ICM).

In this study, we investigated the impact of a TiO2 nanotube (NT) interlayer on the electrochemical performance and service life of Sb and Bi-doped SnO2-coatings synthesized on a titanium mesh. Ti/SnO2-SbBi electrode was synthetized by a thermal decomposition method using ionic liquid as a precursor solvent. Ti/TiO2-NT/SnO2-SbBi electrode was obtained by a two-step electrochemical anodization, followed by the same process of thermal decomposition. The synthesized electrodes were electrochemically characterized and analyzed by scanning electron microscopy and energy dispersive X-ray spectroscopy. Terephthalic acid (TA) experiments showed that Ti/SnO2-SbBi and Ti/TiO2-NT/SnO2-SbBi electrodes formed somewhat higher amounts of hydroxyl radicals (HO) compared with the mesh boron doped diamond (BDD) anode. Electrochemical oxidation experiments were performed using iodinated contrast media (ICM) as model organic contaminants persistent to oxidation. At current density of 50 A m-2, BDD clearly outperformed the synthesized mixed metal oxide (MMO) electrodes, with 2 to 3-fold higher oxidation rates observed for ICM. However, at 100 and 150 A m-2, Ti/SnO2-SbBi had similar performance to BDD, whereas Ti/TiO2-NT/SnO2-SbBi yielded even higher oxidation rates. Disappearance of the target ICM was followed by up to 80% removal of adsorbable organic iodide (AOI) for all three materials, further demonstrating iodine cleavage and thus oxidative degradation of ICM mediated by HO. The presence of a TiO2 NT interlayer yielded nearly 4-fold increase in anode stability and dislocated the oxygen evolution reaction by +0.2 V. Thus, TiO2 NT interlayer enhanced electrode stability and service life, and the electrocatalytic activity for the degradation of persistent organic contaminants.

Antibacterial potential associated with drug-delivery built TiO2 nanotubes in biomedical implants.

The fast evolution of surface treatments for biomedical implants and the concern with their contact with cells and microorganisms at early phases of bone healing has boosted the development of surface topographies presenting drug delivery potential for, among other features, bacterial growth inhibition without impairing cell adhesion. A diverse set of metal ions and nanoparticles (NPs) present antibacterial properties of their own, which can be applied to improve the implant local response to contamination. Considering the promising combination of nanostructured surfaces with antibacterial materials, this critical review describes a variety of antibacterial effects attributed to specific metals, ions and their combinations. Also, it explains the TiO2 nanotubes (TNTs) surface creation, in which the possibility of aggregation of an active drug delivery system is applicable. Also, we discuss the pertinent literature related to the state of the art of drug incorporation of NPs with antibacterial properties inside TNTs, along with the promising future perspectives of in situ drug delivery systems aggregated to biomedical implants.

Powder and Nanotubes Titania Modified by Dye Sensitization as Photocatalysts for the Organic Pollutants Elimination.

In this study, titanium dioxide powder obtained by the sol-gel method and TiO2 nanotubes, were prepared. In order to increase the TiO2 photoactivity, the powders and nanotubes obtained were modified by dye sensitization treatment during the oxide synthesis. The sensitizers applied were Quinizarin (Q) and Zinc protoporphyrin (P). The materials synthesized were extensively characterized and it was found that the dye sensitization treatment leads to modify the optical and surface properties of Titania. It was also found that the effectiveness of the dye-sensitized catalysts in the phenol and methyl orange (MO) photodegradation strongly depends on the dye sensitizer employed. Thus, the highest degradation rate for MO was obtained over the conventional Q-TiO2 photocatalyst. In the case of the nanotubes series, the most effective photocatalyst in the MO degradation was based on TiO2-nanotubes sensitized with the dye protoporfirin (ZnP). Selected catalysts were also tested in the phenol and MO photodegradation under visible light and it was observed that these samples are also active under this radiation.

Modification of the Ti15Mo alloy surface through TiO2 nanotube growth-an in vitro study.

In this study, ordered and uniform TiO2 nanotubular structures were obtained on the surface of the Ti15Mo alloy by anodic oxidation. The amorphous state of TiO2 nanotubes formed under different anodization conditions was investigated. Crystallization of TiO2 into anatase phase occurs during annealing at temperatures of around 400°C, whereas anatase to rutile transformation starts around 500°C and is completed at 800°C. Phase transformations in annealed samples led to morphological changes of tubular nanostructures, suggesting that the oxide layer formed at the nanotube/substrate interface serves as nucleation sites for more stable phases of TiO2. The proliferation of fibroblasts cells under annealing conditions of 450°C, and of untreated samples (control group), was evaluated after 1, 4, and 7 days in cell culture using fluorescence microscopy images. A gradual increase in the number and size of cells was observed, indicating a non-toxic alloy. There was also better surface coverage on anodized samples compared with the untreated group; as well as increased development of the cytoskeleton in samples after anodization. The results of this study showed that the growth of TiO2 nanotubular structures associated with annealing allow better cell adhesion on the Ti15Mo alloy surface.

Formation of nanotubular TiO2 structures with varied surface characteristics for biomaterial applications.

Nanotubular structures were generated on the surface of titanium c.p. by anodization technique in an aqueous solution of acetic acid (14% v/v) with different sources of fluoride ion (HF, NaF, NH4 F). The aim of using these three different compounds is to study the effect of the counterion (H+ , Na+ and NH4+) on the morphology, wettability and surface free energy of the modified surface. Nanotubes were generated at 10 and 15 V for each anodizing solution. To further improve surface characteristics, the samples were heat-treated at 600°C for 4 h and at 560°C for 3 h. SEM images revealed the formation of nanotubes in all anodizing conditions, while their diameter increased proportionally to the electric potential. X-ray diffraction and micro-Raman spectroscopy results showed the presence of both anatase and rutile phases, with a higher content of rutile in the coatings obtained using NH4 F and an applied potential of 10 V. The heat-treatment significantly increased the wettability of the anodic coatings, especially for the coating obtained at 15 V with HF, which showed values < 7 degrees of contact angle. Besides, the nanotubes show a decrease in diameter due to the heat treatment, except for the nanotubes formed in NH4 F. Depending on their surface properties (e.g. low contact angle and high surface free energy), these coatings potentially have great potential in biomedical applications, sensors devices, and catalytic applications among others. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 106A: 1341-1354, 2018.

In Vitro Assessment of Early Bacterial Activity on Micro/Nanostructured Ti6Al4V Surfaces.

It is imperative to understand and systematically compare the initial interactions between bacteria genre and surface properties. Thus, we fabricated a flat, anodized with 80 nm TiO2 nanotubes (NTs), and a rough Ti6Al4V surface. The materials were characterized using field-emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX) and atomic force microscopy (AFM). We cultured in vitro Staphylococcus epidermidis (S. epidermidis) and Pseudomonas aeruginosa (P. aeruginosa) to evaluate the bacterial-surface behavior by FE-SEM and viability calculation. In addition, the initial effects of human osteoblasts were tested on the materials. Gram-negative bacteria showed promoted adherence and viability over the flat and rough surface, while NTs displayed opposite activity with altered morphology. Gram-positive bacteria illustrated similar cellular architecture over the surfaces but with promoted surface adhesion bonds on the flat alloy. Rough surfaces supported S. epidermidis viability, whilst NTs exhibited lower vitality. NTs advocated promoted better osteoblast organization with enhanced vitality. Gram-positive bacteria suggested preferred adhesion capability over flat and carbon-rich surfaces. Gram-negative bacteria were strongly disturbed by NTs but largely stimulated by flat and rough materials. Our work proposed that the chemical profile of the material surface and the bacterial cell wall characteristics might play an important role in the bacteria-surface interactions.

Growth, Structure, and Photocatalytic Properties of Hierarchical V2O5-TiO2 Nanotube Arrays Obtained from the One-step Anodic Oxidation of Ti-V Alloys.

V2O5-TiO2 mixed oxide nanotube (NT) layers were successfully prepared via the one-step anodization of Ti-V alloys. The obtained samples were characterized by scanning electron microscopy (SEM), UV-Vis absorption, photoluminescence spectroscopy, energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (DRX), and micro-Raman spectroscopy. The effect of the applied voltage (30-50 V), vanadium content (5-15 wt %) in the alloy, and water content (2-10 vol %) in an ethylene glycol-based electrolyte was studied systematically to determine their influence on the morphology, and for the first-time, on the photocatalytic properties of these nanomaterials. The morphology of the samples varied from sponge-like to highly-organized nanotubular structures. The vanadium content in the alloy was found to have the highest influence on the morphology and the sample with the lowest vanadium content (5 wt %) exhibited the best auto-alignment and self-organization (length = 1 µm, diameter = 86 nm and wall thickness = 11 nm). Additionally, a probable growth mechanism of V2O5-TiO2 nanotubes (NTs) over the Ti-V alloys was presented. Toluene, in the gas phase, was effectively removed through photodegradation under visible light (LEDs, λmax = 465 nm) in the presence of the modified TiO2 nanostructures. The highest degradation value was 35% after 60 min of irradiation. V2O5 species were ascribed as the main structures responsible for the generation of photoactive e- and h⁺ under Vis light and a possible excitation mechanism was proposed.