A tailored ratiometric fluorescent sensor based on CdTe and MgF2 quantum dots for trace N-ethylpentylone detection.

The development of low-cost and highly sensitive ratiometric fluorescence sensor, CdTe@MIPs/MgF2, for N-Ethylpentylone (NEP) detection in wastewater samples is described. In this system, CdTe@MIPs (λex = 370, λem = 570) are employed as the receptor and response unit for NEP, with MgF2 (λex = 370, λem = 470) as the reference signal to enhance stability. Under optimal conditions, the sensor shows fluorescent quenching response at 570 nm to NEP in linear range of 2-200 nM, with LOD of 0.6 nM. The sensor also demonstrates significant selectivity for NEP over other analogues and interferents, making it ideal for practical applications in wastewater analysis. This approach is potentially more cost-effective and sensitive than conventional mass spectrometry in detecting abused substances in sewage. Additionally, the MgF2 fluorescent nano-material was first-ever developed and investigated, which may be significant in future research.

Instrumental and theoretical advancements in pulsed elution-LC × LC: Investigation of pulse parameters and application to wastewater effluent.

Due to the decoupling of the first (1D) and second (2D) dimension in pulsed elution-LC × LC (PE-LC × LC), method development is more flexible and straightforward compared to fast comprehensive LC × LC where the dependencies of key parameters between the two dimensions limits its flexibility. In this study we present a method for pulse generation, which is based on a switching valve alternating between one pump that delivers the gradient and a second pump that delivers low eluotrophic strength for the pause state. Consequently, the dwell volume of the system was circumvented and 7.5, and 3.75 times shorter pulse widths could be generated at flow rates of 0.2, and 0.4 mL/min with satisfactory accuracies between programmed and observed mobile phase composition (relative deviation of 6.0 %). We investigated how key parameters including pulse width and step height, 2D gradient time and flow rate affected the peak capacity in PE-LC × LC. The conditions yielding the highest peak capacity for the PE-LC × LC- high-resolution mass spectrometry (HRMS) system were applied to a wastewater effluent sample. The results were compared to a one dimensional (1D)-LC-HRMS chromatogram. The peak capacity increased with a factor 34 from 112 for the 1D-LC run to 3770 for PE-LC × LC-HRMS after correction for undersampling. The analysis time for PE-LC × LC-HRMS was 12.1 h compared to 67.5 min for the 1D-LC-HRMS run. The purity of the mass spectra improved for PE-LC × LC-HRMS by a factor 2.6 (p-value 3.3 × 10-6) and 2.0 (p-value 2.5 × 10-3) for the low and high collision energy trace compared to the 1D-LC-HRMS analysis. Furthermore, the signal-to-noise ratio (S/N) was 4.2 times higher (range: 0.06-56.7, p-value 3.8 × 10-2) compared to the 1D-LC-HRMS separation based on 42 identified compounds. The improvements in S/N were explained by the lower peak volume obtained in the PE-LC × LC-HRMS.

Optimisation of analytical methods for tuberculosis drug detection in wastewater: A multinational study.

Wastewater-based epidemiology (WBE) is a robust tool for disease surveillance and monitoring of pharmaceutical consumption. However, monitoring tuberculosis (TB) drug consumption faces challenges due to limited data availability. This study aimed to optimise methods for detecting TB drugs in treated and untreated wastewater from four African countries: South Africa, Nigeria, Kenya, and Cameroon. The limit of detection (LOD) for these drugs ranged from a minimum of 2.20 (±1.02) for rifampicin to a maximum of 2.95 (±0.79) for pyrazinamide. A parallel trend was observed concerning the limit of quantification (LOQ), with rifampicin reporting the lowest average LOQ of 7.33 (±3.44) and pyrazinamide showing the highest average LOQ of 9.81 (±2.64). The variance in LOD and LOQ values could be attributed to factors such as drug polarity. Erythromycin and rifampicin exhibited moderately polar LogP values (2.6 and 2.95), indicating higher lipid affinity and lower water affinity. Conversely, ethambutol, pyrazinamide, and isoniazid displayed polar LogP values (-0.059, -0.6, and -0.7), suggesting lower lipid affinity and greater water affinity. The study revealed that storing wastewater samples for up to 5 days did not result in significant drug concentration loss, with concentration reduction remaining below 1 log throughout the storage period. Application of the optimised method for drug detection and quantification in both treated and untreated wastewater unveiled varied results. Detection frequencies varied among drugs, with ethambutol consistently most detected, while pyrazinamide and isoniazid were least detected in wastewater from only two countries. Most untreated wastewater samples had undetectable drug concentrations, ranging from 1.21 ng/mL for erythromycin to 54.61 ng/mL for isoniazid. This variability may suggest differences in drug consumption within connected communities. In treated wastewater samples, detectable drug concentrations ranged from 1.27 ng/mL for isoniazid to 10.20 ng/mL for ethambutol. Wastewater treatment plants exhibited variable removal efficiencies for different drugs, emphasising the need for further optimisation. Detecting these drugs in treated wastewater suggests potential surface water contamination and subsequent risks of human exposure, underscoring continued research's importance.

Surface-enhanced Raman scattering spectroscopy monitoring and degradation of organic pollutants using a novel nanowire.

A multifunctional Ag/AlOOH nanowires (ANW) composite substrate was constructed, which not only accomplishes highly sensitive detection of organic dye molecules, but also has excellent performance in the degradation of pollutants. The ANW in the Ag/ANW substrate possesses a high aspect ratio, which extends the distribution area of Ag and enables a large number of hot spots on the active substrate. Additionally, due to the abundant OH groups on the ANW, there is an increased number of anchor sites for adsorbed metal ions in the Ag/ANW compound, thus contributing to the enhancement and degradation of molecules. Moreover, the constructed multifunctional Ag/ANW nanocomplexes also show great promise for practical applications, providing a reference for the detection and degradation of contaminants.

Ordered mesoporous hairbrush-like nanocarbon assembled microfibers for solid-phase microextraction of benzene series in oilfield sewage.

The development of advanced functional nanomaterials for solid-phase microextraction (SPME) remains an imperative aspect of sample pretreatment. Herein, we introduce a novel SPME fiber consisting of graphene fibers modified with ordered mesoporous carbon nanotubes arrays (CNTAs) tailored for the determination of benzene series in oilfield wastewater, which is synthesized by an ionic liquid-assisted wet spinning process of graphene nanosheets, followed by a precisely controlled growth of metal-organic framework and subsequent pyrolysis treatment. The resulting robust microfiber structure resembles a "hairbrush" configuration, with a crumpled graphene fiber "stem" and high-order mesoporous CNTAs "hairs". This unique architecture significantly enhances the SPME capacity, as validated by gas chromatography-mass spectrometry. The hairbrush-like nanocarbon assembled microfibers possess structural characteristics, a high specific surface area, and numerous binding sites, offering efficient enrichment of benzene series compounds in oilfield wastewater, including benzene, ethylbenzene, m-xylene, p-xylene, and toluene. Our analysis demonstrates that these microfibers exhibit broad linear ranges (0.2-600 µg L-1), low detection limits (0.005-0.03 mg L-1), and excellent repeatability (3.2-5.5% for one fiber, 2.1-6.7% for fiber-to-fiber) for detection. When compared to commercial alternatives, these hairbrush-like nanocarbon-assembled microfibers exhibit significantly enhanced extraction efficiency for benzene series compounds.

Application of a magnetically separable Zr-MOF for fast extraction of palladium before its spectrophotometric detection.

In this research, a novel magnetic zirconium-based metal-organic framework (Fe3O4@SiO2@MIP-202, MMOF), was fabricated, fully characterized, and applied for the batch-mode solid phase extraction of trace amounts of Pd2+ ions from water and wastewater samples before its spectrophotometric detection. Pd2+ ions were desorbed from MMOF by nitric acid and were complexed by treating with KI solution to have a maximum absorbance at 410 nm. The synthesized MMOF composite showed a very large surface area (65 m2.g- 1), good magnetization (1.7 emu.g- 1) and a large pore volume (0.059 cm3.g- 1) with adsorption capacity of 194.5 mg of Pd2+ ions/g of the adsorbent. This nanosorbent boasts chemo-mechanical stability, high adsorption capacity due to its vast active sites, and facile recovery facilitated by its magnetic properties. Parameters affecting the extraction efficiency of the method were optimized as pH of the sample 7.4, volume of the sample 25 mL, 15 mg adsorbent, 1 mL of 0.1 M HNO3 eluent, with 10 and 15 min as the extraction and desorption times, respectively. The calibration curve was found to be linear across the 10.0-1500.0 µg.L- 1 range with a limit of detection of 1.05 µg.L- 1. The obtained extraction efficiency and enrichment were 98% and 245, respectively. The total analysis time was less than 30 min. This MMOF has never been used for the extraction of Pd2+ ions before.

Feasibility of sulfated BPA and BPS as wastewater-based epidemiology biomarkers: Insights from wastewater and reported human urine analysis.

In wastewater-based epidemiology (WBE), the selection of appropriate biomarkers presents a significant challenge. Recently, sulfated bisphenols have garnered attention as potential WBE biomarkers due to their increased stability in wastewater compared to glucuronide conjugates. This study aims to comprehensively assess the feasibility of employing sulfated BPA and BPS as WBE biomarkers by analyzing both WBE and human biomonitoring data. To conduct this research, wastewater samples were collected from six domestic wastewater treatment plants in Guangzhou, China, and urinary concentration of BPA and BPS were obtained from peer-reviewed literature. The results revealed that mean urinary concentrations of BPA and BPS, calculated using Monte Carlo simulations, significantly exceeded those reported in human biomonitoring studies. Furthermore, the per capita mass load ratio of sulfated BPA and BPS in human urine to the mass load in wastewater was found to be below 10 %. This outcome suggests that the excretion of BPA-S and BPS-S in urine does not make a substantial contribution to wastewater, hinting at the existence of other notable sources. Consequently, our study concludes that sulfated BPA-S and BPS-S are not suitable candidates as WBE biomarkers. This work provides a referenceable analytical framework for evaluating the feasibility of WBE biomarkers and emphasizes the necessity for caution when utilizing WBE to assess human exposure to chemicals.

Ion-Imprinted Polymer-Based Sensor for the Detection of Mercury Ions.

In this work, the development of a novel method for the detection of mercury (II) ions in wastewater using a mercury ion-imprinted polymer (IIP) combined with a quartz crystal microbalance (QCM) is described. The IIP was successfully synthesized via the polymerization of a of a novel fluorescein- and 2-aminophenol-functionalized methacrylic acid monomer, which was noted to have high binding affinity to mercury (II) ions. This polymer was subsequently coated on a QCM chip to create an IIP-QCM sensor. This sensor was established to have high selectivity and good sensitivity to mercury (II) ions, and had a limit of detection (LOD) of 14.17 ppb, a limit of quantification (LOQ) of 42.94 ppb, a signal-to-noise ratio (S/N) of 4.29, good repeatability, and a working range of 42.94 ppb to 2 ppm. The sensor was also able to analyze tap water and wastewater samples. The IIP-QCM is, therefore, promising as a highly selective, cost-effective, and rapid mercury ion sensor for applications involving the detection of mercury in wastewater.

Refining the correction factor for a better monitoring of antidepressant use by wastewater-based epidemiology: A case study of amitriptyline.

Wastewater-based epidemiology (WBE) is proposed as a cost-effective approach to objectively monitor the antidepressant use but it requires more accurate correction factors (CF) than what had been used in previous studies. Amitriptyline is a popular prescription medicine for treating depression and nerve pain, which could be prone to misuse and need monitoring. The CF of amitriptyline employed in previous WBE studies varied from 10 to 100, leading to substantial disparities between WBE estimates and expected mass of antidepressants in wastewater. Hence, this study aimed to take amitriptyline as a case study and refine the CF by correlating mass loads measured in wastewater from 12.2 million inhabitants collected during the 2016 Census with corresponding annual sales data. The triangulation of WBE data and sales data resulted in a newly-derived CF of 7, which is significantly different from the CF values used in previous studies. The newly derived CF was applied to a secondary, multi-year (2017 to 2020) WBE dataset for validation against sales data in the same period, demonstrating the estimated amitriptyline use (380 ± 320 mg/day/1000 inhabitants) is consistent with sales data (450 ± 190 mg/day/1000 inhabitants). When we applied the new CF to previous studies, the wastewater consumption loads matched better to prescription data than previous WBE estimations. The refined CF of amitriptyline can be used in future WBE studies to improve the accuracy of the consumption estimates.

Testing methods to estimate population size for wastewater treatment plants using census data: Implications for wastewater-based epidemiology.

In wastewater-based epidemiology (WBE), wastewater loads are commonly reported as a per capita value. Census population counts are often used to obtain a population size to normalise wastewater loads. However, the methods used to calculate the population size of wastewater treatment plants (WWTPs) from census data are rarely reported in the WBE literature. This is problematic because the geographical extents of wastewater catchments and census area units rarely align perfectly with each other and exist at different spatial scales. This complicates efforts to estimate the number of people serviced by WWTPs in these census area units. This study compared four geospatial methods to combine wastewater catchment areas and census area units to calculate the census population size of wastewater treatment plants. These methods were applied nationally to WWTPs across New Zealand. Population estimates varied by up to 73 % between the methods, which could skew comparisons of per capita wastewater loads between sites. Variability in population estimates (relative standard deviation, RSD) was significantly higher in smaller catchments (rs = -0.727, P < .001), highlighting the importance of method selection in smaller sites. Census population estimates were broadly similar to those provided by wastewater operators, but significant variation was observed for some sites (ranging from 42 % lower to 78 % higher, RSD = 262 %). We present a widely applicable method to calculate population size from census, which involves disaggregating census area units by individual properties. The results reinforce the need for transparent reporting to maintain confidence in the comparison of WBE across sites and studies.

Wastewater-based monitoring of the nitazene analogues: First detection of protonitazene in wastewater.

Synthetic opioids, particularly the nitazene analogues class, have become a public health concern due to their high potency. Wastewater-based epidemiology can detect community use of these compounds. The objective of this work was to detect nitazene analogues in wastewater from samples collected from eight sites in the United States. Influent wastewater samples were collected from eight sites in seven states (Arizona, Oregon, New Mexico, Illinois, New Jersey, Washington and Georgia) in the United States. Samples were collected from each site on three days between 27 December 2022 and 4 January 2023, acidified on collection, stored frozen and shipped to Arizona State University (Tempe, AZ) for sample processing. Samples were then shipped to The University of Queensland (Brisbane, Australia) for sample analysis. Protonitazene was found in samples collected from two sites in Washington and Illinois. The concentration was estimated up to 0.5 ng/L, with estimated excreted mass loads up to 0.3 mg/day/1000 people. This work has shown that it is possible to detect nitazene analogues in wastewater using a combination of sample pre-concentration and sensitive instrumentation, thereby further expanding the utility of wastewater-based epidemiology.

Improving wastewater-based epidemiology for new psychoactive substance surveillance by combining a high-throughput in vitro metabolism assay and LC-HRMS metabolite identification.

One of the primary criteria for a suitable drug biomarker for wastewater-based epidemiology (WBE) is having a unique source representing human metabolism. For WBE studies, this means it is important to identify and monitor metabolites rather than parent drugs, to capture consumption of drugs and not fractions that could be directly disposed. In this study, a high-throughput workflow based on a human liver S9 fraction in vitro metabolism assay was developed to identify human transformation products of new chemicals, using α-pyrrolidino-2-phenylacetophenone (α-D2PV) as a case study. Analysis by liquid chromatography coupled to high resolution mass spectrometry identified four metabolites. Subsequently, a targeted liquid chromatography - tandem mass spectrometry method was developed for their analysis in wastewater samples collected from a music festival in Australia. The successful application of this workflow opens the door for future work to better understand the metabolism of chemicals and their detection and application for wastewater-based epidemiology.

Analytical methods for determining environmental contaminants of concern in water and wastewater.

Control and prevention of environmental pollution have emerged as paramount global concerns. Anthropogenic activities, such as industrial discharges, agricultural runoff, and improper waste disposal, introduce a wide range of contaminants into various ecosystems. These pollutants encompass organic and inorganic compounds, particulates, microorganisms, and disinfection by-products, posing severe threats to human health, ecosystems, and the environment. Effective monitoring methods are indispensable for assessing environmental quality, identifying pollution sources, and implementing remedial measures. This paper suggests that the development and utilization of highly advanced analytical tools are both essential for the analysis of contaminants in water samples, presenting a foundational hypothesis for the review. This paper comprehensively reviews the development and utilization of highly advanced analytical tools which is mandatory for the analysis of contaminants in water samples. Depending on the specific pollutants being studied, the choice of analytical methods widely varies. It also reveals insights into the diverse applications and effectiveness of these methods in assessing water quality and contaminant levels. By emphasizing the critical role of the reviewed monitoring methods, this review seeks to deepen the understanding of pollution challenges and inspire innovative monitoring solutions that contribute to a cleaner and more sustainable global environment.•Urgent global concerns: control and prevention of pollution from diverse sources.•Varied contaminants, diverse methods: comprehensive review of analytical tools.•Inspiring a sustainable future: innovative monitoring for a cleaner environment.

Monitoring the use of novel psychoactive substances in Australia by wastewater-based epidemiology.

Users of novel psychoactive substances (NPS) are at risk, due to limited information about the toxicity and unpredictable effects of these compounds. Wastewater-based epidemiology (WBE) has been used as a tool to provide insight into NPS use at the population level. To understand the preferences and trends of NPS use in Australia, this study involved liquid chromatography mass spectrometry analysis of wastewater collected from Australian states and territories from February 2022 to February 2023. In total, 59 different NPS were included across two complementary analytical methods and covered up to 57 wastewater catchments over the study. The NPS detected in wastewater were 25-B-NBOMe, buphedrone, 1-benzylpiperazine (BZP), 3-chloromethcathinone, N,N-dimethylpentylone (N,N-DMP), N-ethylheptedrone, N-ethylpentylone, eutylone, 4F-phenibut, 2-fluoro deschloroketamine, hydroxetamine, mephedrone, methoxetamine, methylone, mitragynine, pentylone, phenibut, para-methoxyamphetamine (PMA), alpha-pyrrolidinovalerophenone (α-PVP) and valeryl fentanyl. The detection frequency for these NPS ranged from 3 % to 100 % of the sites analysed. A noticeable decreasing trend in eutylone detection frequency and mass loads was observed whilst simultaneously N,N-DMP and pentylone increased over the study period. The emergence of some NPS in wastewater pre-dates other sources of monitoring and provides further evidence that WBE can be used as an additional early warning system for alerting potential NPS use.

Comprehensive two-dimensional liquid chromatography with high resolution mass spectrometry to investigate the photoelectrochemical degradation of environmentally relevant pharmaceuticals and their degradation products in water.

The widespread presence of organic micropollutants in the environment reflects the inability of traditional wastewater treatment plants to remove them. In this context, advanced oxidation processes (AOPs) have emerged as promising quaternary wastewater treatment technologies since they efficiently degrade recalcitrant components by generating highly reactive free radicals. Nonetheless, the chemical characterization of potentially harmful byproducts is essential to avoid the contamination of natural water bodies with hazardous substances. Given the complexity of wastewater matrices, the implementation of comprehensive analytical methodologies is required. In this work, the simultaneous photoelectrochemical degradation of seven environmentally relevant pharmaceuticals and one metabolite from the EU Watch List 2020/1161 was examined in ultrapure water and simulated wastewater, achieving excellent removal efficiencies (overall >95%) after 180 min treatment. The reactor unit was linked to an online LC sample manager, allowing for automated sampling every 15 min and near real-time process monitoring. Online comprehensive two-dimensional liquid chromatography (LC × LC) coupled with high resolution mass spectrometry (HRMS) was subsequently used to tentatively identify degradation products after photoelectrochemical degradation. Two reversed-phase liquid chromatography (RPLC) columns were used: an SB-C18 column operated with 5 mM ammonium formate at pH 5.8 (1A) and methanol (1B) as the mobile phases in the first dimension and an SB-Aq column using acidified water at pH 3.1 (2A) and acetonitrile (2B) as the mobile phases in the second dimension. This resulted in a five-fold increase in peak capacity compared to one-dimensional LC while maintaining the same total analysis time of 50 min. The LC x LC method allowed the tentative identification of 12 venlafaxine, 7 trimethoprim and 10 ciprofloxacin intermediates. Subsequent toxicity predictions suggested that some of these byproducts were potentially harmful. This study presents an effective hybrid technology for the simultaneous removal of pharmaceuticals from contaminated wastewater matrices and demonstrates how multidimensional liquid chromatography techniques can be applied to better understand the degradation mechanisms after the treatment of micropollutants with AOPs.

Automated method for the solid phase extraction of tetracyclines in wastewater followed by fluorimetric determination.

This work presents a multisyringe flow injection analysis (MSFIA) system for the automatic extraction and determination of tetracyclines in wastewater samples. The sample was adjusted with Na2EDTA buffer before solid-phase extraction with an Oasis HLB column used for the analyte preconcentration. The europium (Eu3+)-based and citrate-mediated method (using Tris-HCl buffer) was selected for the fluorimetric analysis (λexc/em = 400/612 nm). For fluorescence detection, a low-cost system consisting of an USB 2000 CCD detector and a 3D-printed support that holds a LED light source was used. Under optimized conditions, the proposed method provided low limits of detection (9.4 µg L-1) and quantification (31 µg L-1), and good values for intra-day (<4 %) and inter-day precisions (<6 %). Recoveries of spiked TCs in wastewater samples ranged from 87 to 106 %. The results of this work were in good agreement with the measurements obtained by liquid chromatography coupled to a fluorescence detector.

Quantitative analysis of drugs of abuse and cognitive enhancers in influent wastewater by means of two chromatographic methods.

Sewage-based epidemiology using influent wastewater is used to estimate the consumption trends of (illicit) drugs over a short or long period of time in a subpopulation. The current study aimed to develop two separate methods for the quantitative analysis of selected drugs of abuse (DOA) and cognitive enhancers in influent wastewater using reversed-phase (RP) or hydrophilic interaction liquid chromatography (HILIC) coupled to high-resolution tandem mass spectrometry (LC-HRMS/MS). The performance of RP and HILIC column was evaluated. A simple solid phase extraction was used for sample preparation. Short runtimes of 10 and 15 min on the RP and the HILIC column, respectively, allowed sufficient throughput. A six-point calibration was used for quantification with calibration ranges between 10 and 100 ng/L for all analytes except for benzoylecgonine (BZE, 30-300 ng/L). Method validation was performed according to ICH guideline M10. Analytes such as amphetamine (AMPH), BZE, cocaethylene (CE), cocaine (COC), ethyl sulfate, 4-hydroxy-3-methoxymethamphetamine, 3,4-methylenedioxymethamphetamine (MDMA), methamphetamine, methylphenidate (MPH), and ritalinic acid (RA) were included in method development and validation. Two different column types were necessary for sufficient chromatographic resolution. The analytical setup allowed detection of all other analytes at concentration levels between 1 ng/L for methylphenidate to 10 ng/L for amphetamine. A method for the detection and quantification of DOA, cognitive enhancers, and their biomarkers in wastewater was successfully developed and validated. Moreover, six proof-of-concept samples were analyzed in which AMPH, BZE, COC, MDMA, MPH, and RA were identified and further quantified.

Automated microextraction by packed sorbent of endocrine disruptors in wastewater using a high-throughput robotic platform followed by liquid chromatography-tandem mass spectrometry.

An automated microextraction by packed sorbent followed by liquid chromatography-tandem mass spectrometry (MEPS-LC-MS/MS) method was developed for the determination of four endocrine disruptors-parabens, benzophenones, and synthetic phenolic antioxidants-in wastewater samples. The method utilizes a lab-made repackable MEPS device and a multi-syringe robotic platform that provides flexibility to test small quantities (2 mg) of multiple extraction phases and enables high-throughput capabilities for efficient method development. The overall performance of the MEPS procedure, including the investigation of influencing variables and the optimization of operational parameters for the robotic platform, was comprehensively studied through univariate and multivariate experiments. Under optimized conditions, the target analytes were effectively extracted from a small sample volume of 1.5 mL, with competitive detectability and analytical confidence. The limits of detection ranged from 0.15 to 0.30 ng L-1, and the intra-day and inter-day relative standard deviations were between 3 and 21%. The method's applicability was successfully demonstrated by determining methylparaben, propylparaben, butylated hydroxyanisole, and oxybenzone in wastewater samples collected from the São Carlos (SP, Brazil) river. Overall, the developed method proved to be a fast, sensitive, reliable, and environmentally friendly analytical tool for water quality monitoring.

Three years of wastewater surveillance for new psychoactive substances from 16 countries.

The proliferation of new psychoactive substances (NPS) over recent years has made their surveillance complex. The analysis of raw municipal influent wastewater can allow a broader insight into community consumption patterns of NPS. This study examines data from an international wastewater surveillance program that collected and analysed influent wastewater samples from up to 47 sites in 16 countries between 2019 and 2022. Influent wastewater samples were collected over the New Year period and analysed using validated liquid chromatography - mass spectrometry methods. Over the three years, a total of 18 NPS were found in at least one site. Synthetic cathinones were the most found class followed by phenethylamines and designer benzodiazepines. Furthermore, two ketamine analogues, one plant based NPS (mitragynine) and methiopropamine were also quantified across the three years. This work demonstrates that NPS are used across different continents and countries with the use of some more evident in particular regions. For example, mitragynine has highest mass loads in sites in the United States, while eutylone and 3-methylmethcathinone increased considerably in New Zealand and in several European countries, respectively. Moreover, 2F-deschloroketamine, an analogue of ketamine, has emerged more recently and could be quantified in several sites, including one in China, where it is considered as one of the drugs of most concern. Finally, some NPS were detected in specific regions during the initial sampling campaigns and spread to additional sites by the third campaign. Hence, wastewater surveillance can provide an insight into temporal and spatial trends of NPS use.

Reusable passive sampler with carbon nanotubes for monitoring contaminants in wastewater: Application, regeneration and reuse.

Progress in excogitation suitable strategies for monitoring chemical compounds in wastewater is an essential step for further research into the occurrence, impact, and fate of the pollutants in the aquatic environment. At present, it is desirable to advance and use economical, environmentally friendly and non-labour intensive methods of environmental analysis. In this study, carbon nanotubes (CNTs) were successfully applied, regenerated, and reused as a sorbent in passive samplers for monitoring contaminants in treated and untreated wastewater at three wastewater treatment plants (WWTPs) located in different urbanization areas in northern Poland. Three cycles of chemical and thermal regeneration of used sorbents were performed. It was shown that it is possible to regenerate CNTs a minimum of three times and reuse them in passive samplers while maintaining the desired sorption properties. The obtained results confirm that the CNTs are perfectly in line with the main principles of green chemistry and sustainability. Carbamazepine, ketoprofen, naproxen, diclofenac, p-nitrophenol, atenolol, acebutolol, metoprolol, sulfapyridine and sulfamethoxazole were detected in each of the WWTPs, both in treated and untreated wastewater. The obtained data drastically show the inefficiency of the removal of contaminants by conventional WWTPs. More importantly, the results even indicate negative contaminant removal in most cases, i.e. higher concentrations (up to 863%) of these substances in the effluent compared to the influent.