Enhancing the properties of swelling soils with lime, fly ash, and expanded polystyrene -A review.

This paper discusses efforts made by past researchers to steady the expansive (problematic) soils using mechanical and chemical techniques - specifically with EPS beads, lime and fly ash. Administering swelling of problematic soils is critical for civil engineers to prevent structural distress. This paper summarizes studies on reduction of swelling potential using EPS, lime and fly ash individually. Chemical stabilization with lime and fly ash are conventional methods for expansive soil stabilization, with known merits and demerits. This paper explores the suitability of different materials under various conditions and stabilization mechanisms, including cation exchange, flocculation, and pozzolanic reactions. The degree of stabilization is influenced by various factors such as the type and amount of additives, soil mineralogy, curing temperature, moisture content during molding, and the presence of nano-silica, organic matter, and sulfates. Additionally, expanded polystyrene (EPS) improves structural integrity by compressing when surrounded clay swells, reducing overall swelling. Thus, EPS addresses limitations of chemicals by mechanical means. Combining EPS, lime and fly ash creates a customized system promoting efficient, long-lasting, cost-effective and eco-friendly soil stabilization. Chemicals address EPS limitations like poor stabilization. This paper benefits civil engineers seeking to control expansive soil swelling and prevent structural distress. It indicates potential of an EPS-lime-fly ash system and concludes by identifying research gaps for further work on such combinatorial stabilizer systems.

New insight into enhanced carbon recovery from anaerobic fermentation of waste activated sludge with cation exchange resin coupled with NaCl pretreatment.

Carbon recovery from waste activated sludge has been attracting considerable attention. However, the migration and transformation patterns of carbon sources between the phases have rarely been reported. In this study, a novel strategy using cation exchange resin (CER) coupled with sodium chloride (NaCl) to enhance carbon recovery through anaerobic fermentation (AF) was proposed. The results demonstrated that CER coupled with NaCl destroyed OH and CO stretching in amide I while promoting the formation of ß-sheet and random coil structures, leading to sludge disintegration. This significantly improved the kinetics of endogenous carbon release, resulting in the release of 1146.33 mg/L of carbon from the solid sludge into the liquid phase. Approximately 75.61 % of the initial carbon source was bio-transformed into short-chain fatty acids. Correspondingly, carbon recovery was significantly increased up to 852.23 mg C/L, 4.57 times that of the control. Mechanism exploration revealed that carbon source recovery was significantly elevated by the synergistic effect of CER and NaCl. CER effectively removed high-valence cations from extracellular polymeric substance (EPS), weakening its bridging and adsorption-electro neutralization capabilities, promoting protein deflocculation, and triggering EPS disruption to release extracellular carbon sources. NaCl disrupted the ionic strength and distribution inside and outside microbial cells, creating an osmotic pressure difference that resulted in cell plasmolysis and lysis, ultimately inducing the release of intracellular carbon sources. Economic and carbon emission reduction benefit analyses verified that the CER coupled with NaCl pretreatment is a cost-effective sludge treatment strategy. This study illustrates the carbon source migration and transformation pathways in the CER coupled with NaCl-assisted AF process, providing guidance for sustainable sludge management.

Remnant Copper Cation-Assisted Atom Mixing in Multicomponent Nanoparticles.

Nanostructured high-/medium-entropy compounds have emerged as important catalytic materials for energy conversion technologies, but complex thermodynamic relationships involved with the element mixing enthalpy have been a considerable roadblock to the formation of stable single-phase structures. Cation exchange reactions (CERs), in particular with copper sulfide templates, have been extensively investigated for the synthesis of multicomponent heteronanoparticles with unconventional structural features. Because copper cations within the host copper sulfide templates are stoichiometrically released with incoming foreign cations in CERs to maintain the overall charge balance, the complete absence of Cu cations in the nanocrystals after initial CERs would mean that further compositional variation would not be possible by subsequent CERs. Herin, we successfully retained a portion of Cu cations within the silver sulfide (Ag2S) and gold sulfide (Au2S) phases of Janus Cu2-xS-M2S (M = Ag, Au) nanocrystals after the CERs, by partially suppressing the transformation of the anion sublattice that inevitably occurs during the introduction of external cations. Interestingly, the subsequent CERs on Janus Cu1.81S-M2S (M = Ag, Au), by utilizing the remnant Cu cations, allowed the construction of Janus Cu1.81S-AgxAuyS, which preserved the initial heterointerface. The synthetic strategy described in this work to suppress the complete removal of the Cu cation from the template could fabricate the CER-driven heterostructures with greatly diversified compositions, which exhibit unusual optical and catalytic properties.

Multiple, simultaneous, independent gradients for a versatile multidimensional liquid chromatography. Part II: Application 3 - Scouting optimization strategies for separation of monoclonal antibodies by dual simultaneous independent gradients of pH & salt on a weak cation exchange stationary phase.

In previous publications we have described the pISep dual simultaneous, independent gradients (DSIGs) liquid chromatography (LC) for uncoupling gradients of non-buffering solute (NaCl, urea or acetonitrile) from externally generated pH gradients. In DSIGs the shape and slope of the [salute] gradient does not depend on the shape and slope of the pH gradient. The technique allows in a single run true simultaneous two dimensional LC separation of complex protein mixtures on various stationary phases including anion, cation exchangers (AEX, CEX), reversed phase (RP), mixed mode and mixed bed. Using a humanized IgG1 (HIgG1) monoclonal antibody (MAb) and a variety of pH & [NaCl] DSIGs, we show that most of MAb isoforms can be successfully separated from each other. These experimental observations are supported by an initial theoretical argument presented here predicting an overall improvement of all MAb isoforms separation by DSIGs of pH & [NaCl]. Theoretical calculations predict that, in general, there exists an optimal non-zero isocratic salt concentration in a pH gradient separation that will resolve isoforms close in binding energy, but a wide range of salt concentrations will be required for acceptable resolution of all isoforms. Theory also predicts better separation of weaker rather than stronger binding isoforms. Experimentally, we have found that no one set of DSIGs LC conditions could optimally baseline resolve all identifiable MAb isoforms in a single run of reasonable duration. The versatility and simplicity of the pH & [NaCl] pISep DSIGs LC allows fast, automated scouting of protein separations over any range of pH from 2.4 to 10.8 and [NaCl] from 0 to 1 M without changing the chemistry of the buffering system. Due to the universal applicability of the pISep buffering system in IEX LC, the researcher is given a powerful tool to easily develop pH & [NaCl] DSIGs protocols that vary mobile phase compositions to achieve high resolution separations of targeted proteins.

Effect of grain size variation on strontium sorption to heterogeneous aquifer sediments.

Strontium-90 (90Sr) is a major contaminant at nuclear legacy sites. The mobility of 90Sr is primarily governed by sorption reactions with sediments controlled by high surface area phases such as clay and iron oxides. Sr2+ adsorption was investigated in heterogeneous unconsolidated aquifer sediments, analogous to those underlying the UK Sellafield nuclear site, with grainsizes ranging from gravels to clays. Batch sorption tests showed that a linear Kd adsorption model was applicable to all grainsize fractions up to equilibrium [Sr] of 0.28 mmol L-1. Sr2+ sorption values (Kd; Langmuir qmax) correlated well with bulk sediment properties such as cation exchange capacity and surface area. Electron microscopy showed that heterogeneous sediments contained porous sandstone clasts with clay minerals (i.e. chlorite) providing an additional adsorption capacity. Therefore, gravel corrections that assumed that the > 2 mm fractions are inert were not appropriate and underestimated Kd(bulk) adsorption coefficients. However, Kd (<2 mm) values measured from sieved sediment fractions, were effectively adjusted to within error of Kd (bulk) using a surface area dependant gravel correction based on particle size distribution data. Amphoteric pH dependent Sr2+ sorption behaviour observed in batch experiments was consistent with cation exchange modelling between pH 2-7 derived from the measured cation exchange capacities. Above pH 7 model fits were improved by invoking a coupled cation exchange/surface complexation which allowed for addition sorption to iron oxide phases. The overall trends in Sr2+ sorption (at pH 6.5-7) produced by increasing solution ionic strength was also reproduced in cation exchange models. Overall, the results showed that Sr2+ sorption to heterogeneous sediment units could be estimated from Kd (<2 mm) data using appropriate gravel corrections, and effectively modelled using coupled cation exchange and surface complexation processes.

Tracking Cation Exchange in Individual Nanowires via Transistor Characterization.

Cation exchange is a versatile method for modifying the material composition and properties of nanostructures. However, control of the degree of exchange and material properties is difficult at the single-particle level. Successive cation exchange from CdSe to Ag2Se has been utilized here on the same individual nanowires to monitor the change of electronic properties in field-effect transistor devices. The transistors were fabricated by direct synthesis of CdSe nanowires on prepatterned substrates followed by optical lithography. The devices were then subjected to cation exchange by submerging them in an exchange solution containing silver nitrate. By removal of the devices from solution and probing the electrical transport properties at different times, the change in electronic properties of individual nanowires could be monitored throughout the entire exchange reaction from CdSe to Ag2Se. Transistor characterization revealed that the electrical conductivity can be tuned by up to 8 orders of magnitude and the charge-carrier mobility by 7 orders of magnitude. While analysis of the material composition by energy dispersive X-ray spectroscopy confirmed successful cation exchange from CdSe to Ag2Se, X-ray fluorescence spectroscopy proved that cation exchange also took place below the contacts. The method presented here demonstrates an efficient way to tune the material composition and access the resulting properties nondestructively at the single-particle level. This approach can be readily applied to many other material systems and can be used to study the electrical properties of nanostructures as a function of material composition or to optimize nanostructure-based devices after fabrication.

Compressibility Studies of Copper Selenides Obtained by Cation Exchange Reaction Revealing the New CsCl Phase.

In this study, we conducted a high-pressure investigation of Cu2-xSe nanostructures with pyramid- and plate-like morphologies, created through cation exchange from zinc-blende CdSe nanocrystals and wurtzite CdSe nanoplatelets respectively. Using a diamond anvil cell setup at the APS synchrotron, we observed the phase transitions in the Cu2-xSe nanostructures up to 40 GPa, identifying a novel CsCl-type lattice with Pm3̅m symmetry above 4 GPa. This CsCl-type structure, previously unreported in copper selenides, was partially retained after decompression. Our results indicate that the initial crystalline structure of CdSe does not affect the stability of Cu2-xSe nanostructures formed via cation exchange. Both morphologies of Cu2-xSe sintered under compression, potentially contributing to the stabilization of the high-pressure phase through interfacial defects. These findings are significant for discovering new phases with potential applications in future technologies.

Titer and charge-based heterogeneity multiattribute monitoring of mAbs in cell culture harvest using 2D ProA CEX MS.

Robust monitoring of heterogeneity in biopharmaceutical development is crucial for producing safe and efficacious biotherapeutic products. Multiattribute monitoring (MAM) has emerged as an efficient tool for monitoring of mAb heterogeneities like deamidation, sialylation, glycosylation, and oxidation. Conventional biopharma analysis during mAb development relies on use of one-dimensional methods for monitoring titer and charge-based heterogeneity using non-volatile solvents without direct coupling with mass spectrometry (MS). This approach requires analysis of mAb harvest by ProA for titer estimation followed by separate cation exchange chromatography (CEX) analysis of the purified sample for estimating charge-based heterogeneity. This can take up to 60-90 min due to the required fraction collection and buffer exchange steps. In this work, a native two-dimensional liquid chromatography (2DLC) mass spectrometry method has been developed with Protein A chromatography in the first dimension for titer estimation and cation exchange chromatography (CEX) in the second dimension for charge variant analysis. The method uses volatile salts for both dimensions and enables easy coupling to MS. The proposed 2DLC method exhibits a charge variant profile that is similar to that observed via the traditional methods and takes only 15 min for mass identification of each variant. A total of six charge variants were separated by the CEX analysis after titer estimation, including linearity assessment from 5 µg to 160 µg of injected mAb sample. The proposed method successfully estimated charge variants for the mAb innovator and 4 of its biosimilars, showcasing its applicability for biosimilarity exercises. Hence, the 2D ProA CEX MS method allows direct titer and charge variant estimation of mAbs in a single workflow.

Solution Processing Silicon Heterojunction Photocathode for Efficient and Stable Hydrogen Production.

Efficient and stable photocathodes are crucial for the development of photoelectrochemical (PEC) water-splitting devices. Silicon heterojunction (SHJ) solar cell is one of the most advanced photovoltaic cells. However, due to the instability of its outermost indium tin oxide (ITO) layers in the electrolyte, a protective layer needs to be introduced on its surface. Previously reported high-quality protective layers almost all involved the use of expensive thin film manufacturing techniques such as atomic layer deposition (ALD). In this work, for the first time, a new strategy is proposed of modifying SHJ-based photocathode with yttrium hydroxide (Y(OH)3) through two-step solution methods to simultaneously improve the stability and activity. The optimized SHJ photocathode exhibits a high applied bias photon-to-current efficiency (ABPE) of 8.4% under simulated 100 mW cm-2 (1 Sun) with an AM 1.5G filter in 0.5 m KOH. Furthermore, the obtained SHJ photocathode demonstrates excellent stability of at least 110 h at 0.3 V versus RHE. In this work, combining facile direct current magnetron sputtering with a solution treatment technique provides a novel design strategy, which lowers the threshold for preparing high-quality protective layer, and paves the way for developing economic, efficient, and stable SHJ-based PEC devices.

Pharmacological intestinal obstruction because of calcium polystyrene sulfonate administration.

Cation exchange resins are commonly used as treatment for hyperkalaemia in patients with chronic renal disease. There is a relation between cation exchange resins and the development of gastrointestinal adverse effects. A case of an intestinal obstruction at the terminal ileum is presented that underwent an ileocolic resection because of a critical stenosis of the intestine. The pathologist revealed abundant inflammatory cells together with deposits of calcium polystyrene crystals responsible of the intestinal obstruction. A rare cause of intestinal obstruction to bear in mind in chronically medicated patients with cation exchange resins.

Rational Design Toward Advanced Non-Flow Aqueous Zinc-Bromine Systems Boosted by Alkaline-Neutral Decoupling Electrolytes.

Non-flow aqueous zinc-bromine batteries (AZBBs) are highly attractive owing to their lightweight construction and largely reduced cost compared with the flow ones. Yet, their development is restricted by the sluggish reaction kinetics of Br2/Br-, the shuttle of soluble polybromide species (Brn -, n is odd), and the poor stability of Zn-based anode. Herein, an effective alkaline-neutral electrolyte decoupling system is constructed to mitigate these issues, where nitrogen-doped carbon felt with high catalytic activity to Br2/Br- reaction is developed for cathode, a cost-effective cation exchange membrane (CEM) of polyethersulfone/sulfonated polyether ether ketone (PES/SPEEK-M) that can stop Brn - is used as separator, and glucose that can inhibit dendrites is introduced as anolyte additive. The constructed flowless AZBB mainly consists of two separate redox couples, including Zn/Zn(OH)4 2- in alkaline anolyte and Br2/Br- in neutral media, where non-cations (e.g. OH-, Zn(OH)4 2-, H2O,  and Brn -) can be restricted to their respective chamber by the PES/SPEEK-M while cations can pass by. In the optimized system, good electrochemical performance is achieved, mainly including a surprising discharge voltage of 2.01 V, a high average Coulombic efficiency of 96.7%, and a good cycling life of ≈1000 cycles without obvious capacity decay at a fixed charge capacity of 2 mAh cm-2.

Achievement of Efficient and Stable Nonflow Zinc-Bromine Batteries Assisted by Rational Decoration upon the Two Electrodes.

Aqueous zinc-bromine batteries (ZBBs) are highly promising because of the advantages of safety and cost. Compared with flow ZBBs, static ones without the assistance of pumping and tank components possess decreased cost and increased energy density and efficiency. Yet, the issues of Zn dendrites and shuttle effect of polybromide ions (Brn-) are more serious in nonflow ZBBs. Meanwhile, the hydrogen evolution reaction (HER) and the sluggish kinetics of the Br2/Br- couple are also in-negligible. Herein, a compressive approach, the cation-exchange membrane (CEM) coating on Zn anodes and N-defect decoration toward carbon felt cathodes, is developed. The CEM with cation-only function can inhibit the formation of Zn dendrites via tuning the Zn2+ flow at the interface, block the noncationic substances, and hence prevent the shuttle of Br2/Brn- and the water decomposition-concerned HER. The optimized nonflow ZBBs can deliver high Coulombic, voltage, and energy efficiencies of 94.1, 92.8, and 87.4%, respectively, which can be well remained in 1000 cycles. Meanwhile, the output voltage is as high as 1.7 V at 10 mA cm-2 with a high areal capacity of 2 mA h cm-2, and a LED with a rated voltage of 1.6 V can be powered successfully, exhibiting high application value.

The influence of cation exchange on the possible mechanism of erionite toxicity: A synchrotron-based micro-X-ray fluorescence study on THP-1-derived macrophages exposed to erionite-Na.

Fibrous erionite is the only zeolite classified as Group 1 carcinogen by the International Agency for Research on Cancer (IARC). Carcinogenesis induced by erionite is thought to involve several factors as biopersistence, the iron role and cation exchange processes. To better understand these mechanisms, a detailed investigation at the micro scale was performed, collecting elemental information on iron and cation release and their distribution in biological systems by synchrotron micro-X-ray fluorescence mapping (SR-micro-XRF) and synchrotron micro-X-ray absorption spectroscopy (SR-micro-XANES) at the TwinMic beamline (Elettra synchrotron) and at the ID21 beamline of the European Synchrotron Radiation Facility (ESRF). By microscopy and chemical mapping, highly detailed maps of the chemical and morphological interaction of biological systems with fibres could be produced. In detail, THP-1 cell line derived macrophages, used as in vitro model, were analysed during erionite-Na phagocytosis at different time intervals, after single dose exposure. For comparison, cellular fluorescent probes were also used to evaluate the intracellular free sodium and calcium concentrations. Synchrotron analyses visualised the spatial distribution of both fibre and mineral particle associated metals during the phagocytosis, describing the mechanism of internalisation of erionite-Na and its accessory mineral phases. The intracellular distribution of metals and other cations was mapped to evaluate metal release, speciation changes and/or cation exchange during phagocytosis. The fluorescent probes complemented microchemical data clarifying, and confirming, the cation distribution observed in the SR-micro-XRF maps. The significant cytoplasmic calcium decrease, and the concomitant sodium increase, after the fibre phagocytosis seemed due to activation of plasma membrane cations exchangers triggered by the internalisation while, surprisingly, the ion-exchange capacity of erionite-Na could play a minor role in the disruption of the two cations intracellular homeostasis. These results help to elucidate the role of cations in the toxicity of erionite-treated THP-1 macrophages and add knowledge to its carcinogenicity process.

[Hydrochemical Characteristics and Genesis Mechanism of Groundwater in the Dry Period in the Zhangjiakou Area].

In order to better support the construction of the capital water conservation functional area and ecological environment support area， research on the chemical characteristics of groundwater and its formation mechanism in the dry period in the Zhangjiakou area can provide a great reference for the rational development and utilization of groundwater resources. A total of 41 groups of groundwater samples were collected， and the hydrochemical types， composition characteristics， and control factors of groundwater in the study area were analyzed by using the combined method of descriptive statistical analysis， Piper triplot， correlation analysis， Gibbs plot， and ion ratio. The results showed that the groundwater in the study area was weakly alkaline， with the total hardness and ρ（TDS） ranging from 105.00 mg·L-1 to 1 433.00 mg·L-1 and 137.00 mg·L-1 to 2 286.00 mg·L-1， respectively. The total hardness and TDS mass concentrations of groundwater in the Bashang area were higher than those in the Baxia area. HCO3- and Na+ were the main dominant anions and cations in the groundwater in the study area. The highest overstandard rate of the main components in groundwater was that of total hardness （36.59%）. The overstandard rate and maximum excess multiple of each component in groundwater in the Bashang area were greater than those in the Baxia area. HCO3-Ca·Mg·Na was the main type of groundwater hydrochemistry in the study area， and there was little difference between the Bashang area and the Baxia area. SO42-， Cl-， HCO3-， Na+， and Mg2+ contributed the most to TDS. The chemical characteristics of groundwater were affected by weathering and filtration of rock minerals such as salt rock， albite， and dolomite； cation exchange； and human activities. Evaporative crystallization and atmospheric precipitation contributed to a small part of the main ion source of groundwater in the area. The effect of human activities on groundwater in the Bashang area was greater than that in the Baxia area， and NO3- mainly originated from agricultural activities.

Development of Structure-Property Relationships for Ammonium Transport through Charged Organogels.

Ammonia is a promising carbon-free fuel, but current methods to produce ammonia are energy intensive. New methods are thereby needed, with one promising method being electrochemical nitrogen reduction cells. Efficient cell operation requires robust catalysts but also efficient membrane separators that permit the selective transport of ions while minimizing the transport of the products across the cell. Commercial membranes have an unknown morphology which makes designing improved cells challenging. To address this problem, we synthesized a series of membranes with controlled crosslinking density and chemical composition to understand their impact on ammonium transport. Higher crosslinking density led to lower ammonium permeability. At the highest crosslinking density, similar ammonium permeability was observed independent of the water volume fraction and hydrophobicity of the monomers. These results suggest new directions to develop membranes with reduced ammonium crossover to improve the efficiency of these electrochemical cells.

Development of a Cation Exchange SPE-HILIC-MS/MS Method for the Determination of Ningnanmycin Residues in Tea and Chrysanthemum.

Ningnanmycin is a widely used antibiotic in agricultural production that effectively controls fungal and viral diseases in tea trees and chrysanthemums. The polarity characteristic of ningnanmycin has posed limitations on the development of robust detection methods, thereby hindering effective monitoring and control measures. By combining cation exchange solid phase extraction (SPE) with hydrophilic interaction chromatography tandem mass spectrometry (HILIC-MS/MS), we have effectively tackled the issue pertaining to the separation and retention of ningnanmycin. The average recoveries of ningnanmycin in green tea, black tea, and chrysanthemum were 77.3-82.0%, 80.1-81.5%, and 74.0-80.0%, respectively. The intraday and interday relative standard deviations (RSDs) were below and equal to 7.7%. Good linearity was observed in the concentration range of 1-1000 µg/L (R2 > 0.998). The limits of detection (LODs) ranged from 1.1 µg/kg to 7.1 µg/kg, and the limits of quantification (LOQs) ranged from 3.6 µg/kg to 23.7 µg/kg for ningnanmycin. These results indicate the good accuracy, repeatability, reproducibility, and sensitivity of the method. It is suitable for detecting ningnanmycin in tea and chrysanthemum.

Advancing Lithium-Magnesium Separation: Pioneering Swelling-Embedded Cation Exchange Membranes Based on Sulfonated Poly(ether ether ketone).

With the continuous advancement of electrodialysis (ED) technology, there arises a demand for improved monovalent cation exchange membranes (CEMs). However, limitations in membrane materials and structures have resulted in the low selectivity of monovalent CEMs, posing challenges in the separation of Li+ and Mg2+. In this investigation, a designed CEM with a swelling-embedded structure was created by integrating a polyelectrolyte containing N-oxide Zwitterion into a sulfonated poly(ether ether ketone) (SPEEK) membrane, leveraging the notable solubility characteristic of SPEEK. The membranes were prepared by using N-oxide zwitterionic polyethylenimine (ZPEI) and 1,3,5-benzenetrlcarbonyl trichloride (TMC). The as-prepared membranes underwent systematic characterization and testing, evaluating their structural, physicochemical, electrochemical, and selective ED properties. During ED, the modified membranes demonstrated notable permeability selectivity for Li+ ions in binary (Li+/Mg2+) systems. Notably, at a constant current density of 2.5 mA cm-2, the modified membrane PEI-TMC/SPEEK exhibited significant permeability selectivity (PMg2+Li+=5.63) in the Li+/Mg2+ system, while ZPEI-TMC/SPEEK outperformed, displaying remarkable permeability selectivity (PMg2+Li+=12.43) in the Li+/Mg2+ system, surpassing commercial monovalent cation-selective membrane commercial monovalent cation-selective membrane (CIMS). Furthermore, in the Li+/Mg2+ binary system, Li+ flux reached 9.78 × 10-9 mol cm-2 s-1 for ZPEI-TMC/SPEEK, while its Mg2+ flux only reached 2.7 × 10-9 mol cm-2 s-1, showing potential for lithium-magnesium separation. In addition, ZPEI-TMC/SPEEK was tested for performance and stability at high current densities. This work offers a straightforward preparation process and an innovative structural approach, presenting methodological insights for the advancement of lithium and magnesium separation techniques.

Cadmium immobilization in soil using phosphate modified biochar derived from wheat straw.

The phosphate-modified biochar (BC) immobilizes cadmium (Cd), yet little is known about how phosphate species affect Cd detoxification in contaminated soils. We developed phosphate-modified biochar through the pyrolysis of wheat straw impregnated with three types of phosphate: mono­potassium phosphate (MKP), dipotassium hydrogen phosphate (DKP), and tripotassium phosphate (TKP). The Cd adsorption mechanism of modified biochar was investigated by biochar characterization, adsorption performance evaluation, and soil incubation tests. The results demonstrated that the efficiency of biochar in immobilizing Cd2+ followed the order: TKP-BC > DKP-BC > MKP-BC. The TKP-BC had the highest orthophosphate content, the fastest adsorption rate, and the largest adsorption capacity (Langmuir) of 257.28 mg/g, which is 6.31 times higher than that of the unmodified BC (CK). In contrast, pyrophosphate was predominant in MKP-BC and DKP-BC. The primary adsorption mechanism for Cd2+ was precipitation, followed by cation exchange, as evidenced by the formation of CdP minerals on the BC surface, and an increase of K+ in solution (compared to water-soluble K+) and a decrease of K+ in the biochar during adsorption. Desorption of Cd from the TKP-BC after adsorption was 9.77 %-12.39 % at a pH of 5-9, much lower than that of CK. The soil incubation test showed the diethylenetriaminepentaacetic acid extracted Cd of TKP-BC, MKP-BC, and DKP-BC was reduced by 67.93 %, 18.41 % and 31.30 % over CK, respectively. Using the planar optodes technique, we also found that TKP-BC had the longest effect enhancing in situ soil pH. This study provides a theoretical basis for developing heavy metal pollution control technology using green remediation materials and offers insights into the remediation mechanisms.

A general strategy for the enhanced H2 production performance of CdS/noble metal sulfide nanorods photocatalysts by cation exchange.

In this work, we report a series of noble metal (Ag, Au, Pt, etc.) sulfides that act as co-catalysts anchoring on CdS nanorods (NRs) obtained via a cation exchange strategy to promote photocatalytic hydrogen evolution. CdS NRs are first generated via a hydrothermal routine, noble metal sulfides are then in-situ grown on CdS NRs by a cation exchange method. CdS/Ag2S, CdS/Au2S and CdS/PtS NRs show improved hydrogen production rates (2506.88, 1513.17 and 1004.54 µmol g-1h-1, respectively), approximately 18, 11 and 7 times higher than CdS NRs (138.27 µmol g-1h-1). Among CdS/noble metal sulfide NRs, CdS/Ag2S NRs present the best H2 production performance. The apparent quantum efficiency (AQE) of CdS/Ag2S NRs achieves 3.11 % at λ = 370 nm. The improved photocatalytic performance of CdS/noble metal sulfide NRs dues to the following points: i) Noble metal sulfides on CdS NRs are beneficial for elevating light-absorbing and light-utilizing capacities, contributing to generating more photoexcited charges; ii) Noble metal sulfides are in-situ grown on CdS NRs as electron acceptors by a cation exchange method, thus the photoexcited electrons generated by CdS NRs rapidly migrate to the surface of noble metal sulfides, successfully accelerating the carriers separation efficiency. This series of noble metal sulfides acting as co-catalysts anchoring on CdS NRs offer new insights into the construction principles of high-performance photocatalytic hydrogen evolution catalysts.

Streamlined Multi-Attribute Assessment of an Array of Clinical-Stage Antibodies: Relationship Between Degradation and Stability.

Clinical antibodies are an important class of drugs for the treatment of both chronic and acute diseases. Their manufacturability is subject to evaluation to ensure product quality and efficacy. One critical quality attribute is deamidation, a non-enzymatic process that is observed to occur during thermal stress, at low or high pH, or a combination thereof. Deamidation may induce antibody instability and lead to aggregation, which may pose immunogenicity concerns. The introduction of a negative charge via deamidation may impact the desired therapeutic function (i) within the complementarity-determining region, potentially causing loss of efficacy; or (ii) within the fragment crystallizable region, limiting the effector function involving antibody-dependent cellular cytotoxicity. Here we describe a transformative solution that allows for a comparative assessment of deamidation and its impact on stability and aggregation. The innovative streamlined method evaluates the intact protein in its formulation conditions. This breakthrough platform technology is comprised of a quantum cascade laser microscope, a slide cell array that allows for flexibility in the design of experiments, and dedicated software. The enhanced spectral resolution is achieved using two-dimensional correlation, co-distribution, and two-trace two-dimensional correlation spectroscopies that reveal the molecular impact of deamidation. Eight re-engineered immunoglobulin G4 scaffold clinical antibodies under control and forced degradation conditions were evaluated for deamidation and aggregation. We determined the site of deamidation, the overall extent of deamidation, and where applicable, whether the deamidation event led to self-association or aggregation of the clinical antibody and the molecular events that led to the instability. The results were confirmed using orthogonal techniques for four of the samples.