ZnO Doped Silica Nanoparticles (ZnO@SiO2) for Enhanced Electrochemical Detection of Cd2+ Ions in Real Samples.

Pollution by heavy metal ions has a serious impact on human health and the environment, which is why the monitoring of heavy metal ions is of great practical importance. In this work, we describe the development of an electrochemical sensor for the detection of cadmium (Cd2+) involving the doping of porous SiO2 spheres with ZnO nanoparticles. Zinc oxide is chosen as the central dopant in the composite material to increase the conductivity and thus improve the electrochemical detection of Cd2+ ions with the SiO2 spheres. The resulting composite is characterized by electrochemical spectroscopic XRD and microscopic methods. As a result, the developed sensor shows good selectivity towards the targeted Cd2+ ions compared to other divalent ions. After optimization of the experimental conditions, the electrochemical sensor shows two different linear ranges between 2.5 × 10-11 molL-1 to 1.75 × 10-10 molL-1 and 2 × 10-9 molL-1 to 1.75 × 10-9 molL-1, indicating a change from diffusion-controlled to surface-controlled oxidation of Cd2+. A detection limit was reached at 4.4 × 10-11 molL-1. In addition, it offers good repeatability and recovery, and can detect accurate trace amounts of Cd2+ ions in real samples such as tap water or seawater by spiking these samples with known Cd2+ concentrations. This setup also provides satisfactory recovery rates in the range of 89-102%.

Surface Modification of Copper-Based Flakes for Conductive Polymer Composites.

The physical properties as well as thermal and electrical stability of copper particles can be improved by surface protection, which mainly depends on the coating material. Our study was, therefore, focused on the rheological, thermal, mechanical and electrical characterization of polymer composites by comparing uncoated (Cu), silver-coated (Cu@Ag) and silica-coated (Cu@Si) copper flakes in low-density polyethylene at various volume concentrations (up to 40%). Interactions among particles were investigated by rheological properties, as these indicate network formation (geometrical entanglement), which is important for mechanical reinforcement as well as establishing an electric pathway (electrical percolation). The results showed that geometrical and electrical percolation were the same for Cu and Cu@Si, ~15%, while, surprisingly, Cu@Ag exhibited much lower percolation, ~7.5%, indicating the fusion of the Ag coating material, which also decreased crystal growth (degree of crystallinity). Furthermore, the magnitude of the rheological and mechanical response remained the same for all investigated materials, indicating that the coating materials do not provide any load transfer capabilities. However, they profoundly affect electron transfer, in that, Cu@Ag exhibited superior conductivity (74.4 S/m) compared to Cu (1.7 × 10-4 S/m) and Cu@Si (1.5 × 10-10 S/m). The results obtained are important for the design of advanced polymer composites for various applications, particularly in electronics where enhanced electrical conductivity is desired.

Bonding of Composite Cements Containing 10-MDP to Zirconia Ceramics Without Dedicated Ceramic Primer.

PURPOSE: To measure zirconia-to-zirconia microtensile bond strength (µTBS) using composite cements with and without primer. MATERIALS AND METHODS: Two Initial Zirconia UHT (GC) sticks (1.8x1.8x5.0 mm) were bonded using four cements with and without their respective manufacturer's primer/adhesive (G-CEM ONE [GOne] and G-Multi Primer, GC; Panavia V5 [Pv5]), and Panavia SA Cement Universal [PSAu], and Clearfil Ceramic Plus, Kuraray Noritake; RelyX Universal (RXu) and Scotchbond Universal Plus [SBUp], 3M Oral Care). Specimens were trimmed to an hour-glass shaped specimen whose isthmus is circular in cross-section. After 1-week water storage, the specimens were either tested immediately (1-week µTBS) or first subjected to 50,000 thermocycles (50kTC-aged µTBS). The fracture mode was categorized as either adhesive interfacial failure, cohesive failure in composite cement, or mixed failure, followed by SEM fracture analysis of selected specimens. Data were analyzed using linear mixed-effects statistics (α = 0.05; variables: composite cement, primer/adhesive application, aging). RESULTS: The statistical analysis revealed no significant differences with aging (p = 0.3662). No significant difference in µTBS with/without primer and aging was recorded for GOne and PSAu. A significantly higher µTBS was recorded for Pv5 and RXu when applied with their respective primer/adhesive. Comparing the four composite cements when they were applied in the manner that resulted in their best performance, a significant difference in 50kTC-aged µTBS was found for PSAu compared to Pv5 and RXu. A significant decrease in µTBS upon 50kTC aging was only recorded for RXu in combination with SBUp. CONCLUSION: Adequate bonding to zirconia requires the functional monomer 10-MDP either contained in the composite cement, in which case a separate 10-MDP primer is no longer needed, or in the separately applied primer/adhesive.

The Optimization of the One-Pot Synthesis of Au@SiO2Core-Shell Nanostructures: Modification with Dansyl Group and Their Fluorescent Properties.

This work describes the optimization of the one-pot synthesis of fine core-shell nanostructures based on nanogold (Au NPs) and silica (SiO2). The obtained core-shell nanomaterials were characterized by Transmission Electron Microscopy (TEM and by the method of spectroscopes such as UV-Vis Spectroscopy and Fourier Transform Infrared Spectroscopy (FT-IR). In addition, the measurement of the zeta potential and size of the obtained particles helped present a full characterization of Au@SiO2 nanostructures. The results show that the influence of reagents acting as reducers, stabilizers, or precursors of the silica shell affects the morphology of the obtained material. By controlling the effect of the added silica precursor, the thickness of the shell can be manipulated, the reducer has an effect on the shape and variety, and then the stabilizer affects their agglomeration. This work provides also a new approach for Au@SiO2core-shell nanostructure preparation by further modification with dansyl chloride (DNS-Cl). The results show that, by tuning the silica shell thickness, the intensity of the fluorescence spectrum of Au@SiO2-(CH2)3-NH-DNS nanocomposite is about 12 times higher than that of DNS-Cl.

Preparation and Characterization of Uniform and Controlled Silica Encapsulating on Lithium Yttrium Fluoride-Based Upconversion Nanoparticles.

In this work, we present an advancement in the encapsulation of lithium yttrium fluoride-based (YLiF4:Yb,Er) upconversion nanocrystals (UCNPs) with silica (SiO2) shells through a reverse microemulsion technique, achieving UCNPs@SiO2 core/shell structures. Key parameters of this approach were optimized to eliminate the occurrence of core-free silica particles and ensure a controlled silica shell thickness growth on the UCNPs. The optimal conditions for this method were using 6 mg of UCNPs, 1.5 mL of Igepal CO-520, 0.25 mL of ammonia, and 50 µL of tetraethyl orthosilicate (TEOS), resulting in a uniform silica shell around UCNPs with a thickness of 8 nm. The optical characteristics of the silica-encased UCNPs were examined, confirming the retention of their intrinsic upconversion luminescence (UC). Furthermore, we developed a reliable strategy to avoid the coencapsulation of multiple UCNPs within a single silica shell. This approach led to a tenfold increase in the UC luminescence of the annealed particles compared to their nonannealed counterparts, under identical silica shell thickness and excitation conditions. This significant improvement addresses a critical challenge and amplifies the applicability of the resulting UCNPs@SiO2 core/shell structures in various fields.

Damage-Free Silica Coating for Colloidal Nanocrystals Through a Proactively Water-Generating Amidation Reaction at High Temperature.

Silica is a promising shell coating material for colloidal nanoparticles due to its excellent chemical inertness and optical transparency. To encapsulate high-quality colloidal nanocrystals with silica shells, the silane coupling hydrolysis is currently the most effective approach. However, this reaction requires water, which often adversely affects the intrinsic physicochemical properties of nanocrystals. Achieving a damage-free silica encapsulation process to nanocrystals by hydrolysis is a huge challenge. Here, a novel strategy is developed to coat colloidal nanocrystals with a denser silica shell via a proactively water-generating reaction at high temperature. In this work, water molecules are continuously and proactively released into the reaction system through the amidation reaction, followed by in situ hydrolysis of silane, completely avoiding the impacts of water on nanocrystals during the silica coating process. In this work, water sensitive perovskite nanocrystals (CsPbBr3) are selected as the typical colloidal nanocrystals for silica coating. Notably, this high-temperature in situ encapsulation technology greatly improves the optical properties of nanocrystals, and the silica shells exhibit a denser structure, providing nanocrystals with better protection. This method overcomes the challenge of the influence of water on nanocrystals during the hydrolysis process, and provides an important reference for the non-destructive encapsulation of colloidal nanocrystals.

Fracture strength of anterior cantilever resin-bonded fixed partial dentures fabricated from high translucency zirconia with different intaglio surface treatments.

PURPOSE: To compare the fracture resistance and failure modes of anterior cantilever resin-bonded fixed partial dentures (RBFPDs) fabricated from high translucency zirconia with different intaglio surface treatments. MATERIALS AND METHODS: Sound-extracted canines (N = 50) were randomly divided into five groups (n = 10) to be restored with high translucency zirconia RBFBDs of different intaglio surface treatments. The RBFPD was designed using exocad software and fabricated using a CAM milling machine. The RBFPDs were treated differently: abrasion with 50 µm alumina particles (Group 1); abrasion with 30 µm silica-coated alumina particles (Group 2); abrasion with silica-coated alumina particles (30 µm) and silane application (Group 3); abrasion with silica-coated alumina particles (30 µm) and 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) primer application (Group 4); abrasion with silica-coated alumina particles (30 µm) and silane, and 10-MDP primer application. All RBFPDs were cemented using dual-cured resin cement. The RBFPDs underwent 6000 thermal cycles with distilled water at 5/55°C for 2 min per cycle and then mechanical cyclic loading with 1200,000 cycles of 50 N at a 1.7 Hz frequency at an angle of 135° to the abutment's long axis. Then, RBFPDs were loaded to fracture using a universal testing machine at 1 mm/min. Maximum fracture forces and failure modes were recorded. Fractured specimens and uncemented specimens were examined using a scanning electron microscope. Data was analyzed using ANOVA and Games-Howell post hoc tests at p < 0.05. RESULTS: Mean fracture load results showed a statistically significant difference between the research groups (p < 0.0001) and it ranged from 69.78 to 584 N. Group 4 exhibited the highest fracture load mean (p < 0.0001) which was significantly different from all other groups. Group 2 recorded a significantly higher fracture load mean than Group 3 (p = 0.029). Three modes of failure were observed: prosthesis debonding, prosthesis fracture, and abutment fracture. CONCLUSIONS: Abrasion of zirconia surface with 30 µm silica-coated alumina particles and application of 10-MDP primer yielded the highest mean fracture loads of monolithic high translucency zirconia RBFPD. The mode of fracture of the RBFPDs was influenced by the type of surface treatments.

Shear bond strength of orthodontic brackets bonded to high-translucent dental zirconia with different surface treatments: An in vitro study.

PURPOSE: The objective of this study was to compare the shear bond strengths of orthodontic brackets bonded to translucent dental zirconia samples which are anatomically accurate and treated with various surface treatments. METHODS: This in vitro study included 156 samples from 3 brands of high-translucent zirconia split into a control group and 4 surface treatment groups: 9.6% hydrofluoric acid etching, 50-micron aluminium oxide particle air abrasion, and 30-micron tribochemical silica coating (TBS) particle air abrasion with and without silane application. After surface treatment, all groups were primed with a 10-MDP primer and bonded to metal orthodontic brackets. Shear bond strength (SBS) was tested and results were compared between all groups. Data analysis consisted of a balanced two-factor factorial ANOVA, a Shapiro-Wilks test, and a non-parametric permutation test. The significance level was set at 0.05. RESULTS: Among all surface treatments, aluminium oxide particle abrasion produced significantly higher SBS (P≤0.002). Lava™ Plus zirconia samples had significantly higher SBS than Cercon® samples (P<0.0001). TBS surface treatment produced significantly higher SBS on Lava™ Plus samples than it did on the other zirconia brands (P=0.032). CONCLUSIONS: This study indicated that mechanical abrasion using aluminium oxide in combination with a 10-MDP primer creates a higher SBS to high-translucent zirconia than the bond created by tribochemical silica coating. Also, there was no significant difference in ARI regardless of zirconia brand or surface preparation.

Improvement of the Self-Controlled Hyperthermia Applications by Varying Gadolinium Doping in Lanthanum Strontium Manganite Nanoparticles.

In this study, silica-encapsulated gadolinium was doped in lanthanum strontium manganite nanoparticles (NPs) with different concentrations using the citrate-gel auto-combustion method. We focused on tuning the Curie temperature and enhancing the specific absorption rate (SAR) of silica-coated gadolinium-doped lanthanum strontium manganite NPs to make them suitable for self-controlled magnetic hyperthermia. The samples were characterized by using transmission electron microscopy (TEM), X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), and magnetic measurements to examine the structural, optical, and magnetic properties of the manganite NPs. While our results exhibit a successful doping of gadolinium in lanthanum strontium manganite NPs, we further prepared magnetic core NPs with sizes between 20 and 50 nm. The Curie temperature of the NPs declined with increasing gadolinium doping, making them promising materials for hyperthermia applications. The Curie temperature was measured using the magnetization (M-T) curve. Magnetic heating was carried out in an external applied AC magnetic field. Our present work proved the availability of regulating the Curie temperature of gadolinium-doped lanthanum strontium manganite NPs, which makes them promising candidates for self-controlled magnetic hyperthermia applications.

Adenosine-Monophosphate-Assisted Homogeneous Silica Coating of Silver Nanoparticles in High Yield.

In this study, we propose a novel approach for the silica coating of silver nanoparticles based on surface modification with adenosine monophosphate (AMP). Upon AMP stabilization, the nanoparticles can be transferred into 2-propanol, promoting the growth of silica on the particle surfaces through the standard Stöber process. The obtained silica shells are uniform and homogeneous, and the method allows a high degree of control over shell thickness while minimizing the presence of uncoated NPs or the negligible presence of core-free silica NPs. In addition, AMP-functionalized AgNPs could be also coated with a mesoporous silica shell using cetyltrimethylammonium chloride (CTAC) as a template. Interestingly, the thickness of the mesoporous silica coating could be tightly adjusted by either the silica precursor concentration or by varying the CTAC concentration while keeping the silica precursor concentration constant. Finally, the influence of the silica coating on the antimicrobial effect of AgNPs was studied on Gram-negative bacteria (R. gelatinosus and E. coli) and under different bacterial growth conditions, shedding light on their potential applications in different biological environments.

Sustained activation of persulfate by slow release of Fe(II) from silica-coated nanosized zero-valent iron for in situ chemical oxidation.

Sustained activation of persulfate through the slow release of Fe(II) from silica-coated nanosized zero-valent iron (nZVI) particles (nZVI@SiO2) was investigated. Slow release of Fe(II) prevented radical scavenging by excess Fe(II) and increased the radical yield, which improved the stoichiometric efficiency of phenol degradation. Sulfate and hydroxyl radicals were found to be the main oxidative species produced during phenol degradation and were found to make comparable contributions to oxidation. The nZVI@SiO2 particle silica shell thickness controlled the release of Fe(II) and therefore the sustained activation of persulfate and was strongly affected by the synthesis conditions, including the [Si]/[Fe] ratio and silica supply rate. Optimal sustained phenol degradation was achieved when nZVI@SiO2 particles were synthesized using a [Si]/[Fe] ratio of 0.5 and a tetraethyl orthosilicate supply rate of 0.5 mL/min, and this was attributed to the nZVI@SiO2 particles giving an optimal Fe(II) release rate and therefore a high persulfate activation rate and a high phenol removal efficiency. Sustained persulfate activation induced by Fe(II) being slowly released was described well by single-stage first-order kinetics rather than two-stage first-order kinetics typical of unmodified nZVI/persulfate systems. Persulfate was found still to be activated by iron (oxyhydr)oxides minerals after the nZVI@SiO2 particles had been exhausted but the persulfate sustained activation induced by the slow release of Fe(II) played a crucial role in determining the overall degradation efficiency. The results highlight the importance of the slow release of Fe(II) from nZVI-based materials for in situ chemical oxidation through sustained persulfate activation.

Zirconia bond strength durability following artificial aging: A systematic review and meta-analysis of in vitro studies.

The present study systematically reviewed the literature regarding the bond strength durability of zirconia ceramics to resin-based luting cements after application of different bonding protocols and aging conditions. Electronic searches in PubMed, Scopus, and Web of Science databases were performed for relevant literature published between January 1st 2015 and November 15th 2022. Ninety-three (93) English language in-vitro studies were included. The percentage of the mean bond strength change was recorded prior to and after artificial aging, and the weighted mean values and 95% confidence intervals were calculated. Bonding protocols were classified based on the combination of MDP/non-MDP containing cement/primer and surface pretreatment, as well as the level of artificial aging performed. Alumina sandblasting (SA) was identified as the most frequently used surface pre-treatment while an insufficient number of studies was identified for each category of alternative surface treatments. The combination of MDP cement with tribochemical silica coating (TSC) or SA yielded more durable results after aging, while the application of SA and TSC improved bond durability when a non-MDP cement and a non-MDP primer were used. TSC may lead to increased bond durability compared to SA, whereas MDP cements may act similarly when combined with SA or TSC.

Digital evaluation of the effect of nanosilica-lithium spray coating on the internal and marginal fit of high translucent zirconia crowns.

OBJECTIVES: To evaluate the effect of a nanosilica-lithium spray coating on the internal and marginal fit of high translucent zirconia crowns using a digital evaluation method. METHODS: A three-dimensional analysis model of a zirconia abutment was digitally scanned using a dental scanner, and 30 monolithic high translucent zirconia crowns were designed and fabricated. They were divided into groups (n = 10) according to the surface treatment method: (1) no treatment: as-sintered zirconia; (2) airborne-particle abrasion with 50 µm Al2O3 particles; and (3) nanosilica-lithium spray coating. Three-dimensional data for the abutment, crown, and crown seated on the abutment were obtained using a dental scanner. The three-dimensional seated fit between the crown and abutment was reconstructed using registration technology, and a three-dimensional (3D) deviation analysis was used to evaluate the effect of different modification methods on the internal and marginal fit of the crowns using root mean square (RMS) values. RESULTS: The 3D deviation analysis of all groups conformed to a normal distribution (P > 0.05), and the variance was homogeneous (P > 0.05). The different surface treatments had no significant effect on the RMS values in the occlusal, axial, and marginal regions of the high translucent zirconia crowns (P > 0.05). CONCLUSIONS: Nanosilica-lithium spray coating for the modification of as-sintered zirconia is clinically feasible and does not affect the internal or marginal fit of high translucent zirconia crowns. CLINICAL SIGNIFICANCE: Nanosilica-lithium spray coating does not affect the adaptation of zirconia crowns and is a clinically feasible surface treatment method for zirconia. It is unnecessary to add the setting values of the internal and marginal fit when fabricating nanosilica-lithium-sprayed zirconia crowns.

Silica-coated gold nanorods biofunctionalization for localized surface plasmon resonance (LSPR) biosensing.

We introduce here the engineering of nanobiosensors designed from gold nanorods coated with an ultrathin layer of silica (AuNR@SiO2) and biofunctionalized with antibodies for the Localized Surface Plasmon Resonance (LSPR) biosensing of proteins. Despite the outstanding properties of AuNRs, their use for LSPR biosensing is limited due to the presence of the surfactant cetyltrimethylammonium bromide (CTAB) - mandatory for their synthesis - which forms a strongly-bounded and positively-charged bilayer at their surface and significantly complicates their bio-functionalization. When coated with a thin layer of silica, these nanomaterials exhibit an improved sensitivity to refractive index change which augurs for better analytical performances. Here, we undertook an in-depth investigation of the biofunctionalization of AuNR@SiO2via three different routes to design and test a label-free LSPR biosensor operating in solution. In the first route, we took advantage of the negatively charged external silica shell to immobilize anti-rabbit IgG antibody by electrostatic physisorption. In the second and third routes, the silica surface was reacted with thiol or aldehyde terminated silanes, subsequently utilized to covalently attach anti-rabbit IgG antibody to the surface. The resulting nanoprobes were characterized by a wide range of physical methods (TEM, XPS, DLS, ELS and UV-Visible spectroscopy) then tested for the biosensing of rabbit-IgG. The three nanobiosensors maintain an excellent colloidal stability after analyte recognition and exhibit extremely high analytical performances in terms of specificity and dynamic range, with an LoD down to 12 ng/mL.

Role of Dipolar Interactions on the Determination of the Effective Magnetic Anisotropy in Iron Oxide Nanoparticles.

Challenging magnetic hyperthermia (MH) applications of immobilized magnetic nanoparticles require detailed knowledge of the effective anisotropy constant (Keff ) to maximize heat release. Designing optimal MH experiments entails the precise determination of magnetic properties, which are, however, affected by the unavoidable concurrence of magnetic interactions in common experimental conditions. In this work, a mean-field energy barrier model (ΔE), accounting for anisotropy (EA ) and magnetic dipolar (ED ) energy, is proposed and used in combination with AC measurements to a specifically developed model system of spherical magnetic nanoparticles with well-controlled silica shells, acting as a spacer between the magnetic cores. This approach makes it possible to experimentally demonstrate the mean field dipolar interaction energy prediction with the interparticle distance, dij , ED ≈ 1/dij 3 and obtain the EA as the asymptotic limit for very large dij . In doing so, Keff uncoupled from interaction contributions is obtained for the model system (iron oxide cores with average sizes of 8.1, 10.2, and 15.3 nm) revealing to be 48, 23, and 11 kJ m-3 , respectively, close to bulk magnetite/maghemite values and independent from the specific spacing shell thicknesses selected for the study.

Nano-silica anti-icing coatings for protecting wind-power turbine fan blades.

Wind power is a promising electricity source. Nevertheless, wind turbine blade icing can cause severe problems in turbine operation. In this study, SiO2 spherical nanoparticles (∼90 nm), produced by RF (radio frequency) plasma spheroidization, were mixed with E51, PDMS, and ethyl acetate, and sprayed on the surface of aluminum plates and regular power windmill fan blades which were already coated with polyurethane primer. XPS and IR spectroscopies revealed the development of SiC and SiPh (Ph = phenolic ring) bonds, whose formation should be favored by the ultrasound and curing processes at 50 °C. The integrity of the coating/substrate interface, whose strength is ascribed to hydrogen bonds, was maintained after 100 icing-melting cycles. The coatings display superhydrophobic behavior and excellent anti-icing performance, along with stability in abrasion, sunlight and self-cleaning ability towards solid pollutants.

Physicochemical and biological characterization of silica-coated alumina particles.

OBJECTIVES: A tribochemical silica-coating (TSC) method has been developed to improve the adhesion of dental resin composites to various substrates. The method utilizes airborne-particle abrasion using particles having a silica surface and an alumina core. The impact of the TSC method has been extensively studied but less attention has been paid to the characterization of the silica-modified alumina particles. Due to the role of silicate ions in cell biology, e.g. osteoblast function and bone mineralization, silica-modified alumina particles could also be potentially used as a biomaterial in scaffolds of tissue regeneration. Thus, we carried out detailed physicochemical characterization of the silica-modified alumina particles. METHODS: Silica-modified alumina particles (Rocatec, 3 M-ESPE) of an average particle size of 30 µm were studied for the phase composition, spectroscopic properties, surface morphology, dissolution, and the capability to modify the pH of an immersion solution. The control material was alumina without silica modification. Pre-osteoblastic MC3T3-E1 cells were used to assess cell viability in the presence of the particles. Cell viability was tested at 1, 3, 7 and 10 days of culture with various particle quantities. Multivariate ANOVA was used for statistical analyses. RESULTS: Minor quantities of silica enrichment was verified on the surface of alumina particles and the silica did not evenly cover the alumina surface. In the dissolution test, no change in the pH of the immersion solution was observed in the presence of the particles. Minor quantities of silicate ions were dissolved from the particles to the cell culture medium but no major differences were observed in the viability of pre-osteoblastic cells, whether the cells were cultured with silica-modified or plain alumina particles. SIGNIFICANCE: Characterization of silica-modified alumina particles demonstrated differences in the particle surface structure compared to control alumina. Dissolution of silica layer in Tris buffer or SBF solution varied from that of cell culture medium: minor quantities of dissolved Si were observed in cell culture test medium. The cell viability test did not shown significant differences between control alumina and its silica-modified counterpart.

Enhancing Resin Cement Adhesion to Zirconia by Oxygen Plasma-Aided Silicatization.

The combinations of alumina particle air abrasion (AA) and a 10-methacryloyloxyidecyl-dihyidrogenphosphate (MDP) primer and a tribochemical silica coating (TSC) and a silane-base primer are contemporary pre-cementation treatments for zirconia restorations for bonding with resin cements. However, the stability of zirconia resists the mechanical or chemical preparations. The purpose of this study was to develop an atmospheric-pressure oxygen plasma (OP)-aided silicatization method to enhance the adhesion of resin cements to zirconia. Zirconia discs were prepared to receive surface treatments of different combinations: (1) AA or TSC (2) with or without OP treatment, and (3) a chemical primer (no primer, silane, or a silane-MDP mixture). The surface morphology, hydrophilicity, and chemical compositions were characterized, and the resin-zirconia bond strengths were examined either after 24 h or a thermocycling test. The results indicated that the OP treatment after the TSC facilitated the homogeneous distribution of silane and crosslinking of silica particles, and effectively improved the hydrophilicity. The OP increased the O and Si and reduced the C elemental contents, while the combination of TSC, OP, and silane induced SiOx generation. Among the groups, only the TSC-OP-silane treatment effectively enhanced the bond strength and maintained the adhesion after thermocycling. With these results, the OP aided the silicatization protocol effectively, generated silane crosslinking, and resulted in superior resin-zirconia bond strength and durability compared to the current treatments.

A Fast, Reliable Oil-In-Water Microemulsion Procedure for Silica Coating of Ferromagnetic Zn Ferrite Nanoparticles Capable of Inducing Cancer Cell Death In Vitro.

The applications of ferrimagnetic nanoparticles (F-MNPs) in magnetic hyperthermia (MH) are restricted by their stabilization in microscale aggregates due to magnetostatic interactions significantly reducing their heating performances. Coating the F-MNPs in a silica layer is expected to significantly reduce the magnetostatic interactions, thereby increasing their heating ability. A new fast, facile, and eco-friendly oil-in-water microemulsion-based method was used for coating Zn0.4Fe2.6O4 F-MNPs in a silica layer within 30 min by using ultrasounds. The silica-coated clusters were characterized by various physicochemical techniques and MH, while cytotoxicity studies, cellular uptake determination, and in vitro MH experiments were performed on normal and malignant cell lines. The average hydrodynamic diameter of silica-coated clusters was approximately 145 nm, displaying a high heating performance (up to 2600 W/gFe). Biocompatibility up to 250 µg/cm2 (0.8 mg/mL) was recorded by Alamar Blue and Neutral Red assays. The silica-coating increases the cellular uptake of Zn0.4Fe2.6O4 clusters up to three times and significantly improves their intracellular MH performances. A 90% drop in cellular viability was recorded after 30 min of MH treatment (20 kA/m, 355 kHz) for a dosage level of 62.5 µg/cm2 (0.2 mg/mL), while normal cells were more resilient to MH treatment.

Tubular electrosynthesis of silica-coated magnetite and evaluation of magnetic nanobiocatalyst efficacy during biomass hydrolysis.

Magnetic nanobiocatalysts (MNBCs) are a promising immobilization approach to ease enzyme recovery during bioprocessing. However, industrial adoption of MNBCs is unfeasible because MNBC-synthesis involves complex and potentially expensive processing steps including synthesis of silica-coated superparamagnetic iron oxide nanoparticles (Si-SPIONs). We developed a single-step process for Si-SPION synthesis using a tubular electrochemical system (TES) and investigated the effect of concentration of the Na2SiO3 coating agent on Si-SPION properties. The Si-SPIONs were used as a support for attachment of polymer-cellulase conjugate to make MNBCs. The spherical Si-SPIONs were 8-12 nm in diameter including a 2-nm silica coating. Na2SiO3 concentration in the reactor did not affect Si-SPION morphology, but increasing Na2SiO3 concentration reduced SPION productivity in the reactor. Protective properties of the SPION silica coatings were demonstrated by showing that they prevented dissolution of SPIONs in an acid solution for 48 h. Enzyme attachment was quantified as protein adsorption on Si-SPIONs which reached 55 µg/mg Si-SPION. The MNBCs were recovered and reused four times. The use of TES for Si-SPION synthesis is promising to reduce MNBC production complexity.