Transferring emergence profile and position of interim restorative implant fixture. A novel digital technique.

The present technical article describes a protocol to digitally reproduce the emergence profile of an interim implant prosthesis (IP) and to transfer its macrogeometry into the definitive restoration. The purpose of this protocol was to minimize alterations in the gingival architecture developed during the interim restorative phase of a single implant that could potentially jeopardize its esthetic outcome. The process included obtaining an intraoral scan with the interim IP in situ, a duplicate of this intraoral scan that was used to capture the exact position of the implant, and an extraoral scan of the prosthesis. These data could then be imported into IOS software to create a model where the patients' soft tissue was incorporated with precision, allowing for the fabrication of a definitive crown with an optimal soft tissue adaptation. As there are few articles in the scientific literature that have reported a consistent method to replicate the emergence profile of an interim IP, the present technical article aims to highlight the potential of utilizing the emergence profile of an interim IP created by IOS software.

Advanced digital planning approach using a 3D-printed mock-up. A case report.

OBJECTIVE: A diagnostic mock-up is a key tool that allows a preview of the outcome of an esthetic restoration. With recent developments in CAD/CAM technology, it is important to understand the pros and cons of chairside digital dentistry and the restorative materials used. The aim of the present case report is to describe in detail the use of a 3D-printed mock-up fabricated from a polymer-based material for an esthetic treatment plan within a fully digital workflow. CASE REPORT: A 45-year-old female patient presented at the clinic concerned about her esthetic appearance and the color of her anterior incisors. After a conclusive diagnosis, a restoration was planned using ceramic veneers from maxillary premolar to premolar. For a preview visualization of the outcome, an intraoral scanner was used to obtain 3D images and to allow the design of a digital smile. The template STL file was exported to a 3D printer and a 0.6-mm mock-up in A3-shade 3D resin was produced after 25 min. The mock-up was tested through a try-in and approved by the patient. As a result, the printed mock-up was considered predictable and reliable for the final restoration. CONCLUSIONS: The ease, speed, and reduced costs derived from the digital workflow, in conjunction with the accuracy of the mock-up, made the procedure highly efficient and recommendable.

Computer-aided designing of a novel multi­epitope DNA vaccine against severe fever with thrombocytopenia syndrome virus.

Severe fever with thrombocytopenia syndrome (SFTS) is an emerging tick-borne viral disease caused by the SFTS virus (Dabie bandavirus), which has become a substantial risk to public health. No specific treatment is available now, that calls for an effective vaccine. Given this, we aimed to develop a multi-epitope DNA vaccine through the help of bioinformatics. The final DNA vaccine was inserted into a special plasmid vector pVAX1, consisting of CD8+ T cell epitopes, CD4+ T cell epitopes and B cell epitopes (six epitopes each) screened from four genome-encoded proteins--nuclear protein (NP), glycoprotein (GP), RNA-dependent RNA polymerase (RdRp), as well as nonstructural protein (NSs). To ascertain if the predicted structure would be stable and successful in preventing infection, an immunological simulation was run on it. In conclusion, we designed a multi-epitope DNA vaccine that is expected to be effective against Dabie bandavirus, but in vivo trials are needed to verify this claim.

Accuracy of semi-occlusive CAD/CAM titanium mesh using the reverse guided bone regeneration digital protocol: A preliminary clinical study.

PURPOSE: The reverse guided bone regeneration protocol is a digital workflow that has been introduced to reduce the complexity of guided bone regeneration and promote prosthetically guided bone reconstruction with a view to achieving optimal implant placement and prosthetic finalisation. The aim of the present study was to investigate the accuracy of this digital protocol. MATERIALS AND METHODS: Sixteen patients with partial edentulism in the maxilla or mandible and with vertical or horizontal bone defects were treated using the reverse guided bone regeneration protocol to achieve fixed implant rehabilitations. For each patient, a digital wax-up of the future rehabilitation was created and implant planning was carried out, then the necessary bone reconstruction was simulated virtually and the CAD/CAM titanium mesh was designed and used to perform guided bone regeneration. The computed tomography datasets from before and after guided bone regeneration were converted into 3D models and aligned digitally. The actual position of the mesh was compared to the virtual position to assess the accuracy of the digital project. Surgical and healing complications were also recorded. A descriptive analysis was conducted and a one-sample t test and Wilcoxon test were utilised to assess the statistical significance of the accuracy. The level of significance was set at 0.05. RESULTS: A total of 16 patients with 16 treated sites were enrolled. Comparing the virtually planned mesh position with the actual position, an overall mean discrepancy between the two of 0.487 ± 0.218 mm was achieved. No statistically significant difference was observed when comparing this to a predefined minimum tolerance (P = 0.06). No surgical complications occurred, but two healing complications were recorded (12.5%). CONCLUSION: Within the limitations of the present study, the reverse guided bone regeneration digital protocol seems to be able to achieve good accuracy in reproducing the content of the virtual plan. Nevertheless, further clinical comparative studies are required to confirm these results.

Effect of milling procedures in CAD-CAM systems on the color changes of CAD-CAM polymethyl methacrylate resin material as interim material.

PURPOSE: This study aimed to investigate the effects of new and used burs on CAD-CAM PMMA resin color changes following thermocycling. MATERIALS AND METHODS: Twenty disk-shaped specimens (10 × 2 mm) were made using a single brand of CAD-CAM polymethyl methacrylate resin (Polident) for the color test. Group N consisted of half of the specimens that were machined using the new tungsten carbide bur set, and Group U consisted of the specimens that were milled using the used bur set (500 machining time). A color test was performed on the specimens both before and after thermocycling. For the statistical analysis, the Kruskal-Wallis and Dunn Pairwise Comparison tests were employed. RESULTS: The ∆E* value of specimens (2.057) milled with the used bur was higher than those of specimens milled with the new bur (0.340), but this value is within clinically acceptable limits. After thermocycling, specimens milled with the utilized burs had the greatest L* (93.850) and b* (5.000) values. After thermocycling, statistically significant differences were discovered between Group N and Group U as well as between specimens milled with the utilized bur before and after thermocycling. CONCLUSION: Thermocycling process have an effect on the mean ∆E values of specimens milled with the used carbide bur, but these ∆E* values were not statistically significant. CLINICAL SIGNIFICANCE: The color and clinical performance of CAD-CAM restorations may be affected by variations in CAD-CAM milling bur properties, particularly those related to their frequent use.

Effect of glazing and thermocycling on the fracture toughness and hardness of a New fully crystallized aluminosilicate CAD/CAM ceramic material.

BACKGROUND: The mechanical properties of fully crystallized lithium aluminosilicate ceramics may be influenced by intraoral temperature variations and postmilling surface treatment. The purpose of this study is to explore the interplay among glazing, thermocycling, and the mechanical characteristics (namely, fracture toughness and hardness) of fully crystallized lithium aluminosilicate ceramics. METHODS: Bending bars (n = 40) cut from LisiCAD blocks (GC, Japan) were randomly assigned to glazed or unglazed groups (n = 20) and subjected to the single edge v-notch beam method to create notches. A glazing firing cycle was applied to the glazed group, while the unglazed group was not subjected to glazing. Half of the specimens (n = 10) from both groups underwent thermocycling before fracture toughness testing. The fracture toughness (KIC) was evaluated at 23 ± 1 °C using a universal testing machine configured for three-point bending, and the crack length was measured via light microscopy. Seven specimens per group were selected for the hardness test. Hardness was assessed using a Vickers microhardness tester with a 1 kg load for 20 s, and each specimen underwent five indentations following ISO 14705:2016. The Shapiro-Wilk and Kolmogorov-Smirnov tests were used to evaluate the normality of the data and a two-way ANOVA was utilized for statistical analysis. The significance level was set at (α = 0.05). RESULTS: Regardless of the thermocycling conditions, the glazed specimens exhibited significantly greater fracture toughness than did their unglazed counterparts (P < 0.001). Thermocycling had no significant impact on the fracture toughness of either the glazed or unglazed specimens. Furthermore, statistical analysis revealed no significant effects on hardness with thermocycling in either group, and glazing alone did not substantially affect hardness. CONCLUSIONS: The impact of glazing on the fracture toughness of LiSiCAD restorations is noteworthy, but it has no significant influence on their hardness. Furthermore, within the parameters of this study, thermocycling was found to exert negligible effects on both fracture toughness and hardness.

3D Printing of Complete Dentures: A Narrative Review.

To explore the applications of 3D printing for the fabrication of complete dentures, a literature search was conducted using PubMed to identify articles related to the topic of 3D-printed complete dentures. A search was conducted that included the following keywords: digital complete denture workflow, printed complete denture, additive manufacturing complete denture, digital complete denture, CAD/CAM complete denture. Articles published before 2016 were excluded to increase the relevancy of reporting results. Determining how 3D-printed dentures compare to conventional and milled dentures is important to better understand how they can be used clinically. Material strength, color stability, and denture base adaptation are discussed. Currently, the area of greatest innovation is with printing resins and improving physical and esthetic properties. As with every innovation, multiple generations of materials are created before the gold standard is achieved. While the ideal printed denture material does not currently exist, based on the published research, printed dentures have material strength that meets ISO standards, with denture base adaptation similar to conventionally processed dentures. Clinically, it is likely that printed dentures will have more challenges with fractures, color stability, and staining. However, printed dentures offer many benefits, and the current limitations will be addressed as new materials are developed. We are currently at the beginning of what is an exciting future for printed dentures.

Manufacturing Accuracy, Intaglio Surface Adaptation, and Survival of Additively and Subtractively Manufactured Definitive Resin Crowns After Cyclic Loading: An In Vitro Study.

PURPOSE: To assess the manufacturing accuracy, intaglio surface adaptation, and survival of resin-based CAD/CAM definitive crowns created via additive manufacturing (AM) or subtractive manufacturing (SM). MATERIALS AND METHODS: A maxillary right first molar crown was digitally designed and manufactured using AM hybrid resin composite (VarseoSmile Crown Plus, Bego [AM-HRC]), AM glass filler-reinforced resin composite (Crowntec, Saremco Dental [AM-RC]), and SM polymer-infiltrated ceramic (Vita Enamic, VITA Zahnfabrik [SM-PICN]). Manufacturing accuracy (trueness and precision) was assessed by computing the root mean square (RMS) error (in µm; n = 15 per material). Intaglio surface adaptation was assessed by calculating the average gap distance (µm). Ten crowns from each group were cemented on fiberglass-reinforced epoxy resin dies and cyclically loaded to simulate 5 years of functional loading. One-way ANOVA, post hoc Bonferroni comparison tests, and Levene's test were used to analyze the data (α = .05). RESULTS: AM-RC had higher overall trueness than AM-HRC and SM-PICN (P ≤ .05), whereas the trueness of AM-RC on the external surface was similar to that of SM-PICN (P = .99) and higher than AM-HRC (P = .001). SM-PICN had lower precision than AM-RC and AM-HRC overall and at internal occlusal surfaces (P ≤ .05). Overall intaglio surface adaptation was similar between all groups (P = .531). However, for the axial intaglio surface, AM-RC and AM-HRC had higher adaptation than SM-PICN (P ≤ .05). All tested crowns survived the cyclic loading simulation of 5 years clinical use. CONCLUSIONS: AM-RC showed high manufacturing accuracy and adaptation. The tested resin-based CAD/CAM materials demonstrated clinically acceptable manufacturing accuracy and simulated medium-term durability, justifying the initiation of clinical investigations to determine their potential implementation in daily clinical practice.

Working Models in the Digital Workflow: Are They Reliable?

PURPOSE: This position paper summarizes all relevant aspects of the use of working models derived from digital data in digital and hybrid workflows, aiming to (1) provide the reader with a comprehensive review of the types of models that currently can be produced from a digital file created by an intraoral scanner (IOS); (2) critically analyze issues that may undermine or compromise their reliability when requested for the fabrication of both tooth-borne and implant-supported fixed dental prostheses (FDPs); and (3) indicate the procedures to be implemented in order to overcome these issues and produce satisfactory restorations. MATERIALS AND METHODS: By way of a thorough literature review, the authors highlight the critical issues of milled and 3D-printed models, solid and alveolar, explaining the differences in terms of accuracy and reliability. RESULTS AND CONCLUSIONS: By describing the peculiarities of models with prepared natural teeth and those incorporating metal implant analogs, the clinical indications for their use are given while proposing the strategies that can be adopted to avoid errors during fabrication or to overcome inaccuracies.

Complete Digital Workflow for Fabricating an Occlusal Device Using Artificial Intelligence- Powered Design Software and Additive Manufacturing: A Dental Method.

Artificial intelligence (AI) has been expanding into areas that were thought to be reserved for human experts and has a tremendous potential to improve patient care and revolutionize the healthcare field. Recently launched AI-powered dental design solutions enable automated occlusal device design. This article describes a dental method for the complete digital workflow for occlusal device fabrication using two different AIpowered design software programs (Medit Splints and 3Shape Automate) and additive manufacturing. Additionally, the benefits and drawbacks of this workflow were reviewed and compared to conventional workflows.

Additive Manufacturing Technologies: Where Did We Start and Where Have We Landed? A Narrative Review.

Additive manufacturing (AM), also known as 3D printing, is gaining burgeoning interest among various dental disciplines. The import of this technology stems not only from its ability to fabricate different parts but from the solutions it provides for the customization and production of complex designs that other methods cannot offer-all to the end of enhancing clinical treatment alternatives. There is a wide range of AM machinery and materials available to choose from, and the goal of this review is to provide readers and clinicians with a decision tool for selecting the appropriate technology for a given application and to successfully integrate AM into the digital workflow.

Positional Trueness with Different Titanium Base Bonding Techniques for Single Implant Crowns: In Vitro Evaluation of Model-Free Workflow Versus Additively Manufactured Models.

OBJECTIVES: To compare the positional trueness of implant-crown bonding to titanium bases (Ti-bases) using different bonding protocols. MATERIALS AND METHODS: A nonprecious alloy model with a single implant at the mandibular right first molar site was digitized, then a single implant crown was designed. The crown was milled, adhesively cemented on a Ti-base, and screw-retained on the implant in the master model to obtain a reference scan. Forty PMMA implant crowns were subtractively manufactured and allocated to one of four study groups (n = 10 crowns per group) based on the bonding protocol on Ti-bases: Group 1 = modelfree bonding; Group 2 = bonding on the master model (control); Group 3 = bonding on a model from an industrial-grade 3D printer (Prodways); Group 4 = bonding on a model from a conventional 3D printer (Asiga). To assess the positional trueness of crowns, the scans of crowns when on the model were superimposed over the reference scan. Median distance and angular deviations were analyzed using Kruskal-Wallis and Mann- Whitney tests (α = .05). Mesial and distal contacts of crowns were assessed by two independent clinicians. RESULTS: The control group (Group 2) resulted in the smallest distance deviations (0.30 ± 0.03 mm) compared to model-free (0.35 ± 0.02 mm; P = .002; Group 1) and conventional 3D printer (0.37 ± 0.01 mm; P = .001; Group 4) workflows. Buccolingual (P = .002) and mesiodistal (P = .01) angular deviations were higher in the conventional 3D printer group than in the control group (P = .002). Proximal contact assessments did not show any differences among groups. CONCLUSIONS: While bonding crowns to Ti-bases on a master model created with an industrial-grade 3D printer resulted in the highest positional trueness, model-free workflows had a similar positional trueness to those manufactured with a conventional 3D printer.

Maximum Fracture Load of Interim Crowns Fabricated by Additive and Subtractive Techniques.

PURPOSE: To evaluate fracture load values of five types of interim CAD/CAM crowns with and without thermocycling. MATERIALS AND METHODS: A complete coverage crown was designed on a mandibular first molar with a uniform 1.5-mm axial and occlusal reduction, and the STL file was exported to manufacture 100 crowns using five materials (20 crowns per material): ZCAD Temp Esthetic (SM-ZCAD; Harvest Dental); Telio CAD (SM-TCAD); P pro Crown and Bridge (AM-PPRO); E-Dent 400 C&B MHF (AM-EDENT); and DENTCA Crown & Bridge (AM-DENTCA). Each group was then divided into two subgroups: before and after thermocycling (10 cornws per subgroup). The STL file of the mandibular first molar die was used to manufacture 100 resin dies. Each die was assigned to one interim crown. Interim crowns were then luted to their assigned die using a temporary luting agent. The fracture strength of crowns was then assessed using a universal testing machine at a crosshead speed of 2 mm/minute. Two-way ANOVA followed by Tukey multiple comparations post-hoc tests were used to assess the effect of material choice and thermocycling process on the fracture strength of interim crowns (α = .05). RESULTS: Material choice and the thermocycling process exerted a significant (P < .001) impact on the fracture strength of interim crowns. However, the interaction between these two factors did not yield a statistically significant effect (P = .176). CONCLUSIONS: Within the limitations of this study, the type of interim materials and thermocycling process have a significant impact on the fracture strength of interim crowns.

Insights into the computer-aided drug design and discovery based on anthraquinone scaffold for cancer treatment: A systematic review.

BACKGROUND: In the search for better anticancer drugs, computer-aided drug design (CADD) techniques play an indispensable role in facilitating the lengthy and costly drug discovery process especially when natural products are involved. Anthraquinone is one of the most widely-recognized natural products with anticancer properties. This review aimed to systematically assess and synthesize evidence on the utilization of CADD techniques centered on the anthraquinone scaffold for cancer treatment. METHODS: The conduct and reporting of this review were done in accordance to the Preferred Reporting Items for Systematic Reviews and Meta-analysis (PRISMA) 2020 guideline. The protocol was registered in the "International prospective register of systematic reviews" database (PROSPERO: CRD42023432904) and also published recently. The search strategy was designed based on the combination of concept 1 "CADD or virtual screening", concept 2 "anthraquinone" and concept 3 "cancer". The search was executed in PubMed, Scopus, Web of Science and MedRxiv on 30 June 2023. RESULTS: Databases searching retrieved a total of 317 records. After deduplication and applying the eligibility criteria, the final review ended up with 32 articles in which 3 articles were found by citation searching. The CADD methods used in the studies were either structure-based alone (69%) or combined with ligand-based methods via parallel (9%) or sequential (22%) approaches. Molecular docking was performed in all studies, with Glide and AutoDock being the most popular commercial and public software used respectively. Protein data bank was used in most studies to retrieve the crystal structure of the targets of interest while the main ligand databases were PubChem and Zinc. The utilization of in-silico techniques has enabled a deeper dive into the structural, biological and pharmacological properties of anthraquinone derivatives, revealing their remarkable anticancer properties in an all-rounded fashion. CONCLUSION: By harnessing the power of computational tools and leveraging the natural diversity of anthraquinone compounds, researchers can expedite the development of better drugs to address the unmet medical needs in cancer treatment by improving the treatment outcome for cancer patients.

Immediate Loading Using the Digitalized Customized Restoration of Single-tooth Implants Placed in Fresh Extraction Sockets in the Aesthetic Anterior Maxilla: A 10-Year Prospective Study of Marginal Bone Level.

AIM: The objective of this study was to assess marginal bone level around single implants inserted in fresh extraction sockets in the anterior maxillary region and instantly restored with computer-aided design/computer-aided manufacturing customized temporary crowns cemented on the final abutment. MATERIALS AND METHODS: A total of 20 patients (15 females and 5 males, with a mean age of 30 years), where 20 were placed in fresh extraction sockets. After raising a full-thickness flap, atraumatic extraction was performed the implant site was prepared and fixtures were stabilized on the palatal bone wall. The implant location was immediately transmitted to the prepared master model using the pick-up impression coping seated in the surgical guide template. Prefabricated abutments were used as the final abutment on the master model, scanned and the crown was planned using computer-aided manufacturing customized software. Later on 8th weeks, abutments were torqued as per the manufacturer's recommendation, and the final crowns were cemented. Using personalized intraoral radiographs marginal bone level was evaluated mesially and distally to the implant shoulder as a reference at implant placement, 8 weeks, 1, 3, 5, and 10 years after loading. RESULTS: Wholly implants were osteo-integrated positively after 10 years of practical loading, but only 18 were available for clinical and radiological follow-up, and 2 patients with two implants were excluded from the study due to relocation abroad without any implant failure. The average marginal bone loss (MBL) in the current report was 0.16 ± 0.167 mm at crown cementation, 0.275 ± 0.171 mm after 1 year, 0.265 ± 0.171 mm after 3 years, 0.213 ± 0.185 mm after 5 years, and 0.217 ± 0.194 mm at 10 years. CONCLUSION: The strategy of inserting and not removing the final abutment at the time of implant placement facilitates the establishment of adequate attachment of both soft and hard tissues to the abutment surface, ensuring uninterrupted organization of tissue architecture and offers advantages in helping maintain soft tissue maturation and preventing marginal bone level. CLINICAL SIGNIFICANCE: Immediately loaded implants in freshly extracted sockets lead to a significant reduction in marginal ridge resorption. The use of a temporary crown on a prefabricated abutment, exclusive of successive abutment manipulation, proved effective in preserving the primarily founding blood clot and served as a prototype for shaping the soft tissue around the previously wounded gum. How to cite this article: Berberi A, El Zoghbi A, Aad G, et al. Immediate Loading Using the Digitalized Customized Restoration of Single-tooth Implants Placed in Fresh Extraction Sockets in the Aesthetic Anterior Maxilla: A 10-Year Prospective Study of Marginal Bone Level. J Contemp Dent Pract 2024;25(3):213-220.

Replacement of unsatisfactory ceramic veneers with the aid of a digital workflow.

This case report focuses on the replacement of ceramic laminate veneers with suboptimal marginal fit and design, employing a digital workflow and CAD-CAM technology. The patient, a woman in her 30s, expressed concerns about the appearance and hygiene challenges of her existing veneers. A comprehensive assessment, including clinical examination, facial photographs and intraoral scanning, was conducted. Utilising CAD software, facial photographs and 3D models merged to create a digital wax-up, crucial in designing suitable veneers and addressing issues like overcontouring and a poor emergence profile. Following the removal of old veneers, a mock-up was performed and approved. Preparations ensured space for restorations with well-defined margins. The final restorations, milled with Leucite-reinforced vitreous ceramic, were cemented. At the 1 year follow-up, improved aesthetics, gingival health and functional restorations were observed. This report highlights the efficacy of digital workflows in achieving consistent and aesthetically pleasing outcomes in ceramic laminate veneer replacement.

Maxillomandibular relationship record methods for computer-engineered complete dentures: a scoping review.

OBJECTIVES: The purpose of this scoping review was to identify different methods employed for recording the maxillomandibular relationship (MMR) for computer-aided designed and manufactured (CAD-CAM) complete dentures (CDs). MATERIALS AND METHODS: This scoping review followed the PRISMA-ScR guidelines and was developed according to Arksey and O'Malley and The Joanna Briggs Institute protocol. The methods were registered on the Open Science Framework (< osf.io/rf4xm> ). The focus question was: "What are the different techniques for recording the maxillomandibular relationship in the digital workflow used in CECDs?" Two investigators searched 3 online databases [MEDLINE (PubMed), Scopus, and Science Direct] independently. The inclusion criteria were clinical studies and reviews that assessed techniques for recording MMR using digital workflow for manufacturing of CECDs. A descriptive analysis was performed considering the study design, manufacturing system, clinical steps, and tools for the determination of MMR, and the difficulty level of procedures. RESULTS: 4779 articles were identified in the electronic search and 10 studies were included for data analysis. The review identified 4 commercially available CAD-CAM denture systems and 3 innovative methods suitable for abbreviating the number of appointments (2 to 4 visits). The trial denture is inherent to the procedure for the Baltic System and 3 innovative techniques. Three techniques (2 innovative and WholeYouNexteeth) demonstrated lower difficulty levels for performing the clinical procedures, regardless of the professional skills. CONCLUSIONS: The commercially available and innovative techniques for the recording of MMR may provide predictability of the treatment. The techniques are effective, however, rely on the learning curve and the patient's clinical condition. CLINICAL RELEVANCE: Recording of the maxillomandibular relationship is paramount for the manufacturing and functionality of complete dentures. Clinicians should be aware of the different tools and techniques described for registering the jaw relationship.

Bone reconstruction using CAD/CAM technology in head and neck surgical oncology. A narrative review of state of the art and aesthetic-functional outcomes.

Bone defects following resections for head and neck tumours can cause significant functional and aesthetic defects. The choice of the optimal reconstructive method depends on several factors such as the size of the defect, location of the tumour, patient's health and surgeon's experience. The reconstructive gold standard is today represented by revascularised osteo-myocutaneous or osteomuscular flaps with osteosynthesis using titanium plates. Commonly used donor sites are the fibula, iliac crest, and lateral scapula/scapular angle. In recent years, computer-aided design (CAD)/computer assisted manufacturing (CAM) systems have revolutionised the reconstructive field, with the introduction of stereolithographic models, followed by virtual planning software and 3D printing of plates and prostheses. This technology has demonstrated excellent reliability in terms of accuracy, precision and predictability, leading to better operative outcomes, reduced surgical times and decreased complication rates. Among the disadvantages are high costs, implementation times and poor planning adaptability. These problems are finding a partial solution in the development of "in house" laboratories for planning and 3D printing. Strong indications for the use of CAD/CAM technologies today are the reconstruction of total or subtotal mandibular or maxillary defects and secondary bone reconstructions.

Evaluation of the effect of different core substrates on the accuracy of intraoral scanners.

BACKGROUND: The aim of this study was to determine if different types of core substrates have any effect on the trueness and precision of digital intraoral impressions. MATERIAL AND METHODS: A customized typodont with four similar cores of natural dentine, composite, metal (Ni-Cr), and zirconia in the position of premolars was fabricated. The study model was scanned five times with two types of intraoral scanners (Carestream 3600 and 3Shape Trios 3), and a reference standard scan was obtained using a laboratory scanner (3shape D1000). A metrology software (Geomagic X) was used to align the data of experimental scans and the reference scan to determine deviation values (trueness). Precision values were calculated with random superimposition in each intraoral scanner group. The Kruskal-Wallis test was used to compare differences between different substrates, and the Mann-Whitney test was used to compare the average values between the two scanners. RESULTS: Trios 3 was found to be significantly truer and more precise than Carestream 3600 (p value = .005, <0.001). There were no significant differences in the trueness of different substrates when they were scanned by Trios 3, while different materials showed significantly different trueness values in the Carestream 3600 group (p value = .003). Dentin showed the best trueness, and zirconia performed worse than other substrates. Regarding the precision of the scanners, neither of the scanners was affected by the type of scanning substrate. CONCLUSION: For Carestream 3600, substrate type did impact the trueness of intraoral scans, with dentin and zirconia showing the highest and lowest accuracy, respectively, while Trios 3 was similarly accurate across all substrates. Trios 3 had both higher trueness and precision than Carestream 3600.

Efficient complete denture metal base design via a dental feature-driven segmentation network.

BACKGROUND AND OBJECTIVE: Complete denture is a common restorative treatment in dental patients and the design of the core components (major connector and retentive mesh) of complete denture metal base (CDMB) is the basis of successful restoration. However, the automated design process of CDMB has become a challenging task primarily due to the complexity of manual interaction, low personalization, and low design accuracy. METHODS: To solve the existing problems, we develop a computer-aided Segmentation Network-driven CDMB design framework, called CDMB-SegNet, to automatically generate personalized digital design boundaries for complete dentures of edentulous patients. Specifically, CDMB-SegNet consists of a novel upright-orientation adjustment module (UO-AM), a dental feature-driven segmentation network, and a specific boundary-optimization design module (BO-DM). UO-AM automatically identifies key points for locating spatial attitude of the three-dimensional dental model with arbitrary posture, while BO-DM can result in smoother and more personalized designs for complete denture. In addition, to achieve efficient and accurate feature extraction and segmentation of 3D edentulous models with irregular gingival tissues, the light-weight backbone network is also incorporated into CDMB-SegNet. RESULTS: Experimental results on a large clinical dataset showed that CDMB-SegNet can achieve superior performance over the state-of-the-art methods. Quantitative evaluation (major connector/retentive mesh) showed improved Accuracy (98.54 ± 0.58 %/97.73 ± 0.92 %) and IoU (87.42 ± 5.48 %/70.42 ± 7.95 %), and reduced Maximum Symmetric Surface Distance (4.54 ± 2.06 mm/4.62 ± 1.68 mm), Average Symmetric Surface Distance (1.45 ± 0.63mm/1.28 ± 0.54 mm), Roughness Rate (6.17 ± 1.40 %/6.80 ± 1.23 %) and Vertices Number (23.22 ± 1.85/43.15 ± 2.72). Moreover, CDMB-SegNet shortened the overall design time to around 4 min, which is one tenth of the comparison methods. CONCLUSIONS: CDMB-SegNet is the first intelligent neural network for automatic CDMB design driven by oral big data and dental features. The designed CDMB is able to couple with patient's personalized dental anatomical morphology, providing higher clinical applicability compared with the state-of-the-art methods.