Combined UMBAF-MBAF process treating detergent wastewater.

A combined process of the upflow multimedium biological aerated filter (UMBAF) and the multimedia biological aerated filter (MBAF) treating detergent wastewater was investigated in this study. Results showed that the optimal filtration rate of the combined system was 1.4 m/hr while the optimized performance was observed at air to water ratio of 2:1. The average removal rate of chemical oxygen demand (COD), linear alkyl benzene sulfonate sodium (LAS), and total phosphate (TP) was up to 91.4%, 88.5%, and 40%, respectively, while the average effluent concentrations of COD, LAS, and TP under stable operation states were 35.0 mg/L, 7.0 mg/L, and 4.4 mg/L, respectively. UMBAF played a major role in TP removal; the removal of COD in the combined UMBAF and MBAF process was consistent with the general formula C = C0 e -(ah + b) , while the kinetic model of LAS removal in the combined UMBAF and MBAF process could be expressed by L = L0 e-(mh + n) . The combined UMBAF-MBAF process provides a promising technology for the treatment of detergent wastewater. The kinetic model of LAS removal in the UMBAF and MBAF units is helpful for the prediction of the treatment efficiency of organic pollutants. PRACTITIONER POINTS: A novel UMBAF-MBAF process was developed treating detergent wastewater. The average removal rate of COD, LAS, and TP by the combined process was up to 91.4%, 88.5%, and 40%, respectively. Kinetic models for the UMBAF-MBAF process were investigated.

Sodium dodecyl sulfate removal during electrospray ionization using cyclodextrins as simple sample solution additive for improved mass spectrometric detection of peptides.

Sodium dodecyl sulfate (SDS) removal is a vital procedure in SDS-assisted bottom-up proteomics because SDS affects the quality of the data in electrospray ionization mass spectrometry (ESI-MS). SDS removal methods provide efficient removal of SDS and improved peptide analysis, but would usually require time, specialised devices, and experienced analysts. Here, by simple addition of γ-cyclodextrin (γ-CD) to the solution at concentrations 1 to 2x the SDS in the sample, the SDS related signals in positive ionization ESI-MS can be significantly removed (70-99% reduction), without an additional sample manipulation step of extraction or purification. The mechanism for removal is based on the formation of tightly bound CD-SDS inclusion complexes, which hampered the generation of positively charged SDS multimers during ESI. For a sample with peptides (glu-val-phe, tyr-tyr-tyr, and bradykinin) and 3 mM SDS where 6 mM γ-CD was added, the %signal recoveries of peptides calculated by comparison with signals from standard samples without SDS were 49-59%. The space charge effect by SDS on bradykinin was also reduced, increasing the signal for bradykinin 12x in the presence of γ-CD. For a protein (bovine serum albumin, BSA) digest with 3 mM SDS, which is an expected concentration in trypsin treated samples, a noticeable 7-fold improvement in the peptide to SDS signal ratio and a 91% reduction of SDS signals were observed upon addition of 6 mM γ-CD. However, there were only small changes in the ESI-MS intensities for the BSA peptides (compared to without addition of γ-CD). This new approach to SDS signal removal using CDs in ESI-MS may find use in proteomic studies.

Optimisation of saponin extraction conditions with Camellia sinensis var. assamica seed and its application for a natural detergent.

BACKGROUND: Camellia sinensis var. assamica seed cake (a by-product of tea-seed oil) is an abundant resource with poor utilisation. C. sinensis var. assamica seed saponin (CSS) is one kind of non-ionic surfactant. In this study, the CSS extraction conditions were optimised by response surface methodology (RSM) and then the CSS detergent was developed. Additionally, the safety and decontamination ability of the developed detergent were evaluated. RESULTS: The optimised extraction conditions were including the extracting temperature of 40.04 °C, extraction time of 4.97 h, ethanol concentration of 64.11% and liquid-solid ratio of 14.57:1 mL g-1 . The formula of the CSS detergent was as follows: 20% crude CSS, 0.3% oxidised tea polyphenols (OTPs), 0.2% nisin, 0.3% sodium dehydroacetate, 0.7% sodium alginate and 0.5% sodium polyacrylate. The LD50 of the CSS detergent exceeds 14 g kg-1 in mice, indicating the detergent was non-toxic. Both of the emulsifying and the pesticide residues removal abilities of the CSS detergent were significantly stronger than the commercial detergent. CONCLUSION: A natural tea seed saponin detergent with good safety and decontamination ability was successfully developed. This can make better use of the tea seed cake, thereby creating added value in the tea seed oil industry. © 2017 Society of Chemical Industry.

Reutilização do detergente enzimático: avaliação do impacto da contaminação microbiana da solução na efetividade da limpeza de aparelhos endoscópicos gastrointestinais / Enzymatic detergent reuse: evaluation of the impact of the solution's microbial contamination on the cleaning effectiveness of gastrointestinal endoscopes

No Brasil, é recomendado que durante a limpeza dos Produtos para Saúde (PPS) o detergente utilizado possua ação enzimática. Embora a Resolução da Diretoria Colegiada nº 55 de 14 de novembro de 2012 da Agência Nacional de Vigilância Sanitária desaconselhe a reutilização desta solução de limpeza, sabe-se que na prática clínica elas são reaproveitadas por diversas vezes para imersão de PPS, como os aparelhos endoscópicos, o que pode comprometer a efetividade da ação do detergente enzimático e com isso a segurança no processamento do PPS. Esta pesquisa objetivou avaliar a carga microbiana presente na solução de detergente enzimático durante sua reutilização na limpeza manual de aparelhos endoscópicos gastrointestinais. Tratou-se de um estudo transversal realizado em um serviço de endoscopia digestiva de um hospital universitário de Belo Horizonte e no Laboratório de Microbiologia Oral e Anaeróbios do ICB/UFMG. A amostra foi composta por 57 aparelhos endoscópicos e 76 alíquotas de solução de detergente enzimáticos coletadas de diversos reusos de 19 diferentes soluções. O material coletado foi agitado em vórtex, acrescido a Caldo Letheem Modificado e submetido a filtração em membrana Millipore® 0,45µm. A membrana foi depositada em Tryptic Soy Ágar para crescimento microbiano. A identificação presuntiva dos micro-organismos foi realizada manualmente considerando-se aspectos morfotintoriais e reações bioquímico/fisiológicas. As variáveis foram descritas utilizando frequências, porcentagens e medidas de tendência central. O projeto foi aprovado pelo Comitê de Ética e Pesquisa da Universidade Federal de Minas Gerais (CAAE ­ 67493417.1.0000.5149). As médias das cargas microbianas na solução de detergente enzimático variaram de 19,9 UFC/mL após primeiro uso, 51,1 UFC/mL após terceiro uso e 67,1UFC/mL após o quinto reuso. Nos canais de ar/água e biópsia houve aumento de micro-organismos Gram negativos ao longo das reutilizações do detergente. Foram recuperados, Enterobacter spp., Escherichia coli, Klebsiella spp., Pseudomonas spp., Staphyloccocus aureus, Staphyloccocus coagulase negativa. Pseudomonas spp. foi o micro-organismo mais identificado em todas as alíquotas coletadas. Verificou-se a importância da escovação do canal de biópsia para correta remoção de micro-organismos. Conclui-se que a reutilização das soluções de detergente enzimático contribuiu para contaminação dos aparelhos endoscópicos com micro-organismos potencialmente patogênicos. Faz-se necessário a reavaliação de protocolos institucionais, no sentido de que seja cumprida a orientação da Anvisa por meio da RDC nº 55 de 14 de novembro de 2012 de que os detergentes enzimáticos não devem ser reutilizados sob perda da eficiência do produto. As características físico químicas dos detergentes enzimáticos devem ser respeitadas pelos serviços de saúde conforme parâmetros estabelecidos pelos fabricantes.(AU)

In Brazil, it is recommended that during the cleaning of Health Products the detergent used has enzymatic action. Although Collegiate Board Resolution No. 55 of November 14, 2012 of the National Agency of Sanitary Surveillance advises against the reuse of this cleaning solution, it is known that in clinical practice they are reused several times for immersion of health products, such a gastrointestinal endoscope, which may compromise the effectiveness of the enzymatic detergent action and thus the safety in the processing. This research aimed to evaluate the microbial load present in the enzymatic detergent solution during its reuse in the manual cleaning of endoscopic gastrointestinal devices. This was a cross-sectional study performed at a gastrointestinal endoscopy service at a university hospital in Belo Horizonte and at the Oral Microbiology and Anaerobic Laboratory of ICB/UFMG. The sample consisted of 57 endoscopes and 76 aliquots of enzymatic detergent solution collected from several replicates of 19 different solutions. The collected material was vortexed, added to Modified Letheem Broth and subjected to Millipore® 0.45 µm membrane filtration. The membrane was deposited in Tryptic Soy Ágar for microbial growth. The identification of the microorganisms was performed manually considering morphotintorial aspects and biochemical/physiological reactions. The variables were described using frequencies, percentages and measures of central tendency. The project was approved by the Ethics and Research Committee of the Federal University of Minas Gerais (CAAE - 67493417.1.0000.5149). The mean values of the microbial loads in the enzymatic detergent solution varied from 19.9 UFC/mL after first use, 51.1 UFC/mL after third use and 67.1 UFC/mL after the fifth reuse. In the air/water and biopsy channels there was an increase of Gram negative microorganisms along the reuse of the detergent. Enterobacter spp., Escherichia coli, Klebsiella spp., Pseudomonas spp., Staphylococcus aureus, Coagulase-negative Staphyloccocus were recovered. Pseudomonas spp. was the most identified microorganism in all aliquots collected. It was verified the importance of brushing the biopsy channel for correct removal of microorganisms. It was concluded that the reuse of enzyme detergent solutions contributed to the contamination of the endoscopes with potentially pathogenic microorganisms. It is necessary to re-evaluate institutional protocols, in order to comply with Anvisa's guidance through RDC nº. 55 of November 14, 2012 that enzymatic detergents should not be reused under loss of product efficiency. The physical characteristics of the enzymatic detergents must be observed by the health services according to the parameters established by the manufacturers.(AU)

Comparative Evaluation of Small Molecular Additives and Their Effects on Peptide/Protein Identification.

Detergents and salts are widely used in lysis buffers to enhance protein extraction from biological samples, facilitating in-depth proteomic analysis. However, these detergents and salt additives must be efficiently removed from the digested samples prior to LC-MS/MS analysis to obtain high-quality mass spectra. Although filter-aided sample preparation (FASP), acetone precipitation (AP), followed by in-solution digestion, and strong cation exchange-based centrifugal proteomic reactors (CPRs) are commonly used for proteomic sample processing, little is known about their efficiencies at removing detergents and salt additives. In this study, we (i) developed an integrative workflow for the quantification of small molecular additives in proteomic samples, developing a multiple reaction monitoring (MRM)-based LC-MS approach for the quantification of six additives (i.e., Tris, urea, CHAPS, SDS, SDC, and Triton X-100) and (ii) systematically evaluated the relationships between the level of additive remaining in samples following sample processing and the number of peptides/proteins identified by mass spectrometry. Although FASP outperformed the other two methods, the results were complementary in terms of peptide/protein identification, as well as the GRAVY index and amino acid distributions. This is the first systematic and quantitative study of the effect of detergents and salt additives on protein identification. This MRM-based approach can be used for an unbiased evaluation of the performance of new sample preparation methods. Data are available via ProteomeXchange under identifier PXD005405.

Optimized Triton X-114 assisted lipopolysaccharide (LPS) removal method reveals the immunomodulatory effect of food proteins.

SCOPE: Investigations into the immunological response of proteins is often masked by lipopolysaccharide (LPS) contamination. We report an optimized Triton X-114 (TX-114) based LPS extraction method for ß-lactoglobulin (BLG) and soy protein extract suitable for cell-based immunological assays. METHODS AND RESULTS: Optimization of an existing TX-114 based phase LPS extraction method resulted in >99% reduction of LPS levels. However, remaining TX-114 was found to interfere with LPS and protein concentration assays and decreased viability of THP-1 macrophages and HEK-Blue 293 cells. Upon screening a range of TX-114 extraction procedures, TX-114-binding beads were found to most effectively lower TX-114 levels without affecting protein structural properties. LPS-purified proteins showed reduced capacity to activate TLR4 compared to non-treated proteins. LPS-purified BLG did not induce secretion of pro-inflammatory cytokines from THP-1 macrophages, as non-treated protein did, showing that LPS contamination masks the immunomodulatory effect of BLG. Both HEK293 cells expressing TLR4 and differentiated THP-1 macrophages were shown as a relevant model to screen the protein preparations for biological effects of LPS contamination. CONCLUSION: The reported TX-114 assisted LPS-removal from protein preparations followed by bead based removal of TX-114 allows evaluation of natively folded protein preparations for their immunological potential in cell-based studies.

Sensitivity of mass spectrometry analysis depends on the shape of the filtration unit used for filter aided sample preparation (FASP).

Efficient protein solubilization using detergents is required for in-depth proteome analysis, but successful LC-MS/MS analysis greatly depends on proper detergents removal. A commonly used sample processing method is the filter-aided sample preparation (FASP), which allows protein digestion and detergent removal on the same filtration device. Many optimizations of the FASP protocol have been published, but there is no information on the influence of the filtration unit typology on the detergents removal. The aim of this study was to compare the performance of conic and flat bottom filtration units in terms of number of proteins identified by LC-MS/MS. We have analyzed 1, 10 and 100 µg of total cell lysate prepared using lysis buffer with different SDS concentrations. We compared the FASP protocol using conic and flat bottom filtration units to ethanol precipitation method. Subsequently, we applied our most performant protocol to single murine pancreatic islet, and identified up to 2463 protein using FASP versus 1169 proteins using ethanol precipitation. We conclude that FASP performance depends strongly on the filter shape: flat bottom devices are better suited for low-protein samples, as they allow better SDS removal leading to the identification of greater number of proteins.

A novel method to determine residual detergent in biological samples post endotoxin reduction treatment and evaluation of strategies for subsequent detergent removal.

Endotoxin removal using detergent washes and extractions are well-established, efficient, and cost-effective methods; however, removing residual detergent post treatment has been shown to be a challenge. In this communication, we show a simple and fast method for determining the detergent concentration in a protein solution post treatment and highlight strategies for detergent removal to achieve levels below the critical micelle concentration (CMC), the minimum concentration at which detergent micelles form.

Whole-body tissue stabilization and selective extractions via tissue-hydrogel hybrids for high-resolution intact circuit mapping and phenotyping.

To facilitate fine-scale phenotyping of whole specimens, we describe here a set of tissue fixation-embedding, detergent-clearing and staining protocols that can be used to transform excised organs and whole organisms into optically transparent samples within 1-2 weeks without compromising their cellular architecture or endogenous fluorescence. PACT (passive CLARITY technique) and PARS (perfusion-assisted agent release in situ) use tissue-hydrogel hybrids to stabilize tissue biomolecules during selective lipid extraction, resulting in enhanced clearing efficiency and sample integrity. Furthermore, the macromolecule permeability of PACT- and PARS-processed tissue hybrids supports the diffusion of immunolabels throughout intact tissue, whereas RIMS (refractive index matching solution) grants high-resolution imaging at depth by further reducing light scattering in cleared and uncleared samples alike. These methods are adaptable to difficult-to-image tissues, such as bone (PACT-deCAL), and to magnified single-cell visualization (ePACT). Together, these protocols and solutions enable phenotyping of subcellular components and tracing cellular connectivity in intact biological networks.

Inducing two-dimensional crystallization of membrane proteins by dialysis for electron crystallography.

Electron crystallography is an electron cryo-microscopy (cryo-EM) method that is particularly suitable for structure-function studies of small membrane proteins, which are crystallized in two-dimensional (2D) arrays for subsequent cryo-EM data collection and image processing. This approach allows for structural analysis of membrane proteins in a close-to-native, phospholipid bilayer environment. The process of growing 2D crystals from purified membrane proteins by dialysis detergent removal is described in this chapter. A short section covers screening for and identifying 2D crystals by transmission electron microscopy, and in the last section, optimization of the purification to obtain crystals of higher quality is discussed.

Solvent/detergent-treated plasma: a tale of 30 years of experience.

Solvent/detergent-treated plasma was licensed >30 years ago. It has several specific characteristics, the most important being the standardized content of clotting factors, the lack of antibodies implicated in transfusion-related acute lung injury pathogenesis and the very high level of safety against transfusion-related viral infections. Since 1992, many clinical studies have confirmed its safety and efficacy in a wide range of congenital and acquired bleeding disorders. After a brief analysis of the pharmaceutical characteristics of solvent/detergent plasma, this review will focus on the clinical experience with this virus-inactivated plasma.

The removal of Triton X-100 by dialysis is feasible!

Triton X-100 has been widely used in many analytical and preparative protocols for a long time. Nevertheless, mass spectrometry, chromatographic separation, and spectrophotometric readout may be considerably hampered by this detergent due to signal suppression, complex formation, and high blank values, respectively. Additionally, Triton X-100 is not safe to remove prior to analytics. Here, microdialysis is introduced as a parallelizable, high-throughput method to clean samples from Triton X-100 with high efficacy and precision. To achieve this, we exploit the potential to considerably increase the critical micellar concentration of Triton X-100 by alteration of matrix properties. To that end, addition of several chaotropic compounds and organic solvents has been shown to increase the critical micellar concentration as well as the removal rate of the detergent. For application, matrix additives can be selected for analyte stability requirements out of a variety of compounds. Conveniently, all these additives are removable subsequently using the same microdialysis tool for downstream analytics requirements. Applicability and protocols are shown with proteomic sample preparation of purified proteins and complex protein mixtures prior to matrix-assisted laser desorption ionization (MALDI) mass spectrometry.

The biotechnological potential of subtilisin-like fibrinolytic enzyme from a newly isolated Lactobacillus plantarum KSK-II in blood destaining and antimicrobials.

An antimicrobial oxidative- and SDS-stable fibrinolytic alkaline protease designated as KSK-II was produced by Lactobacillus plantarum KSK-II isolated from kishk, a traditional Egyptian food. Maximum enzyme productivity was obtained in medium containing 1% lactose and 0.5% soybean flour as carbon and nitrogen sources, respectively. Purification of enzyme increased its specific activity to 1,140-fold with a recovery of 33% and molecular weight of 43.6 kDa. Enzyme activity was totally lost in the presence of ethylenediaminetetraacetic acid and was restored after addition of Fe(2+) suggesting that KSK-II is a metalloprotease and Fe(2+) acts as cofactor. Enzyme hydrolyzed not only the natural proteins but also synthetic substrates, particularly Suc-Ala-Ala-Pro-Phe-pNA. KSK-II can hydrolyze the Lys-X easier than Arg-X; thus, it was considered as a subtilisin-family protease. Its apparent Km , Vmax , and Kcat were 0.41 mM, 6.4 µmol mg(-1) min(-1) , and 28.0 s(-1) , respectively. KSK-II is industrially important from the perspectives of its maximal activity at 50°C (stable up to 70°C), ability to function at alkaline pH (10.0), stability at broad pH ranges (7.5-12.0) in addition to its stability toward SDS, H2 O2 , organic solvents, and detergents. We emphasize for the first time the potential of fibrinolytic activity for alkaline proteases used in detergents especially in blood destaining.

[Structure identification of contaminants in a beverage product by liquid chromatography coupled with quadrupole time-of-flight mass spectrometry].

The contaminants in a beverage product that had been reported to have a strange taste were identified. By comparative analysis with the normal product using liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (LC-QTOF-MS), six unknown compounds were detected in the total ion current chromatograms of the product in question. Detailed analysis of the mass spectra and product ion spectra of these compounds strongly suggested that the compounds were capric acid diethanolamide, lauric acid diethanolamide, myristic acid diethanolamide, lauryl dimethylaminoacetic acid, lauryl sulfate, and lauric acid, all of which are surfactants commonly used as ingredients of household detergents and shampoos. We searched commercially available detergent products to check for the presence of these six surfactants, and identified products that might have been intentionally or unintentionally mixed into the beverage product after opening.

Characterization of thermostable serine alkaline protease from an alkaliphilic strain Bacillus pumilus MCAS8 and its applications.

This study describes the characterization and optimization of medium components for an extracellular detergent, surfactant, organic solvent and thermostable serine alkaline protease produced by alkaliphilic Bacillus pumilus MCAS8 strain isolated from Pulicat lake sediments, Tamil Nadu, India. The strain yielded maximum protease (2,214 U/ml) under optimized conditions: carbon source, citric acid-1.5 % (w/w); inducer, soyabean meal-2 % (w/w); pH 11.0; shaking condition 37 °C for 48 h. The enzyme had pH and temperature optima of 9.0 and 60 °C, respectively. The enzyme displayed the molecular mass of 36 kDa in sodium dodecyl sulphate-polyacrylamide gel electrophoresis study and exhibited activity at a wide range of pH (6.0-11.0) and thermostability (20-70 °C). More than 70 % residual activity was observed when the enzyme was incubated with dithiothreitol, ethylenediaminetetraacetic acid, ethylene glycol tetraacetic acid and H(2)O(2) for 30 min. The protease activity was also enhanced by divalent cations such as Ba(2+), Ca(2+) and Mg(2+) and was strongly inhibited by Fe(2+), Zn(2+), Sr(2+), Hg(2+) and urea. The enzyme retained more than 50 % of its initial activity after pre-incubation for 1 h in the presence of 5 % (v/v) organic solvents such as dimethyl sulphoxide and acetone. The protease could hydrolyse various native proteinaceous substrates (1 % w/v) such as bovine serum albumin, casein, skim milk, gelatine, azocasein and haemoglobin. Wash performance analysis of enzyme revealed that it could effectively remove blood stains from the cotton fabric, thus making it suitable to use as an effective detergent additive. The protease enzyme also exhibited promising result in the dehairing of goat skin. The potency of the eco-friendly enzyme without using any chemicals against washing and dehairing showed that the enzyme could be used for various industrial applications.

Removal of detergents from proteins and peptides in a spin-column format.

To enable downstream analysis, it is critical to remove unbound detergents from protein and peptide samples. This unit describes the use of a high-performance resin that offers exceptional detergent removal for proteins and peptides. The easy-to-use spin format significantly improves results over the standard drip column and batch methodologies, with >95% removal of 1% to 5% detergents, including SDS, sodium deoxycholate, CHAPS, Triton X-100, Triton X-114, NP-40, Brij-35, octyl glucoside, octyl thioglucoside, and lauryl maltoside, with high recovery of proteins and peptides. Detergent removal efficiency is evaluated using colorimetric methods and mass spectrometry (MS). BSA tryptic peptides have been successfully analyzed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) and matrix-assisted laser desorption/ionization (MALDI)-MS for identification of protein, following detergent removal using the resin. Advantages of this method include speed (less than 15 min), efficient detergent removal, and high recovery of proteins and peptides.

Ion-pair in-tube solid-phase microextraction and capillary liquid chromatography using a titania-based column: application to the specific lauralkonium chloride determination in water.

A quick, miniaturized and on-line method has been developed for the determination in water of the predominant homologue of benzalkonium chloride, dodecyl dimethyl benzyl ammonium chloride or lauralkonium chloride (C(12)-BAK). The method is based on the formation of an ion-pair in both in-tube solid-phase microextraction (IT-SPME) and capillary liquid chromatography. The IT-SPME optimization required the study of the length and nature of the stationary phase of capillary and the processed sample volume. Because to the surfactant character of the analyte both, the extracting and replacing solvents, have played a decisive role in the IT-SPME optimized procedure. Conditioning the capillary with the mobile phase which contains the counter ion (acetate), using an organic additive (tetrabutylammonium chloride) added to the sample and a mixture water/methanol as replacing solvent (processed just before the valve is switched to the inject position), allowed to obtain good precision of the retention time and a narrow peak for C(12)-BAK. A reversed-phase capillary based TiO(2) column and a mobile phase containing ammonium acetate at pH 5.0 for controlling the interactions of cationic surfactant with titania surface were proposed. The optimized procedure provided adequate linearity, accuracy and precision at the concentrations interval of 1.5-300 µg L(-1) .The limit of detection (LOD) was 0.5 µg L(-1) using diode array detection (DAD). The applicability of proposed IT-SPME-capillary LC method has been assessed in several water samples.

Convenient and rapid removal of detergent from glycolipids in detergent-resistant membrane microdomains.

Although detergents are often essential in protocols, they are usually incompatible with further biochemical analysis. There are several methods for detergent removal, but the procedures are complicated or suffer from sample loss. Here, we describe a convenient and rapid method for detergent removal from sialic acid-containing glycosphingolipids (gangliosides) and neutral glycolipids in detergent-resistant membrane (DRM) microdomain. It is based on selective detergent extraction, in which the sample is dried on a glass tube, followed by washing with organic solvent. We investigated 18 organic solvents and used high performance thin-layer chromatography (HPTLC) and matrix-assisted laser desorption/ionization quadrupole ion trap time-of-flight mass spectrometry (MALDI-QIT-TOF MS) to confirm that dichloroethane (DCE) was the most suitable solvent and completely removed the nonionic detergent Triton X-100. Furthermore, DCE extraction effectively removed interference caused by other nonionic, zwitterionic, or ionic detergents in MALDI-QIT-TOF MS analysis.

Efficient removal of detergents from proteins and peptides in a spin column format.

Detergents are commonly used in protein-chemistry protocols and may be necessary for protein extraction, solubilization, and denaturation; however, their presence interferes with many downstream analysis techniques, including mass spectrometry (MS). To enable downstream analysis, it is critical to remove unbound detergents from protein and peptide samples. In this study, we describe a high-performance resin that offers exceptional detergent removal for proteins and peptides. When used in a spin column format, this resin dramatically improves protein and peptide MS results by more than 95% removal of 1-5% detergents, including sodium dodecyl sulfate (SDS), sodium deoxycholate, Chaps, Triton X-100, Triton X-114, NP-40, Brij-35, octyl glucoside, octyl thioglucoside, and lauryl maltoside, with high recovery of proteins and peptides. Postcolumn liquid chromatography-tandem MS (LC-MS/MS) analysis of trypsin digests of bovine serum albumin (BSA) and HeLa cell lysate revealed excellent sequence coverage, indicating successful removal of detergent from the peptides. Matrix-assisted laser desorption/ionization (MALDI)-MS analysis of unprocessed and processed samples further confirmed efficient removal of detergents. The advantages of this method include speed (<15min), efficient detergent removal, and high recovery of proteins and peptides.

Efficient electrophoretic method to remove neutral additives from protein solutions followed by mass spectrometry analysis.

A mass spectrometry (MS)-compatible, isoelectric point-based separation method for removal of neutral additives from protein solutions is described. The separation is performed by electrophoretic migration and trapping using a device referred to as membrane separated wells for isoelectric focusing and trapping (MSWIFT). Electrophoretic separation in the MSWIFT device is fast; the entire process can be carried out in a matter of minutes, and it does not require further sample cleanup prior to MS analysis. Proof-of-concept experiments in which neutral additives (e.g., Triton X-100, Tween 20, poly(ethylene glycol)) are removed from protein solutions using the MSWIFT device followed by MS analysis are described. Coupling the MSWIFT separation with ion mobility MS provides additional separation via the gas phase and assists in achieving higher quality ESI mass spectra when small amounts of additives remain in solution.