An effective configuration for automated magnetic micro solid-phase extraction of phenylurea herbicides from water samples followed by high-performance liquid chromatography.

In this study, a new automated magnetic micro solid-phase extraction was introduced. A Tygon tube was folded and fixed around the pole of a cylindrical magnet. Nanosized magnetic sorbents modified with diphenyldichlorosilane were uniformly immobilized on one side of the inner wall of the tube. Sample solution and desorption solvent were passed through the tube using a peristaltic pump. Four phenylurea herbicides (tebuthiuron, monolinuron, isoproturon, and monuron) were used as the model compounds to evaluate the method performance. HPLC-UV was used to separate and quantify the analytes. The effective parameters influencing the performance of the extraction process (i.e., extraction and desorption flow rates, eluent and sample volumes, type of eluent and sample ionic strength) were investigated. The limit of detection was 0.04 µg L-1 for all studied compounds. Calibration curves were linear in the range of 0.1-500 µg L-1 with a determination coefficient between 0.9988 and 0.9999. Intra-day, inter-day and batch-to-batch precisions expressed as relative standard deviation were less than 7%. Several environmental water samples were investigated to assess the applicability of the method for real sample analysis.

An accurate and robust LC-MS/MS method for the quantification of chlorfenvinphos, ethion and linuron in liver samples.

A method for the determination of chlorfenvinphos, ethion and linuron in liver samples by LC-MS/MS is described. Sample treatment was performed by using Sola™ polymeric reverse phase SPE cartridges after protein precipitation. Gradient elution using 10 mM ammonium formate in methanol (A) and 10 mM ammonium formate in water (B) was used for chromatographic separation of analytes on a Hypersil™ end-capped Gold PFP reverse phase column (100 mm × 2.1 mm, 3 µm). All analytes were quantified without interference, in positive ionization mode using multiple reaction monitoring (MRM) with chlorfenvinphos-d10 as internal standard. The whole procedure was validated according to the FDA guidelines for bioanalytical methods. The calibration curves for chlorfenvinphos, linuron and ethion compounds were linear over the concentration range of 0.005-2 µM (i.e. 0.0018-0.720 µg/mL, 0.0019-0.770 µg/mL and 0.0012-0.500 µg/mL respectively) with coefficients of determination higher than 0.998. A Lower limit of quantification of 0.005 µM was achieved for all analytes, i.e. 5.76, 6.08 and 3.84 µg/kg of liver for chlorfenvinphos, ethion and linuron respectively. Compounds extraction recovery rates ranged from 92.9 to 99.5% with a RSD of 2.3%. Intra- and inter-day accuracies were within 90.9 and 100%, and imprecision varied from 0.8 to 8.2%. Stability tests proved all analytes were stable in liver extracts during instrumental analysis (+12 °C in autosampler tray for 72 h) at the end of three successive freeze-thaw cycles and at -20 °C for up to 9 months. This accurate and robust analytical method is therefore suitable for contamination or metabolism studies.

Study of processes influencing bioavailability of pesticides in wood-soil systems: Effect of different factors.

Lignocellulosic wastes and by-products containing lignin are now available in large amounts from forestry and industrial activities, and could be promising organic materials for the biosorption of pesticides by soils in order to reduce point-source pollution. Adding these materials to soil requires understanding the process of pesticide sorption-desorption by wood-soils, as sorption capacity could increase, with changes in pesticide bioavailability and final fate. The objective of this work was to study the effect that pine and oak wood added to soils had on the sorption/desorption of the pesticides linuron, alachlor, and metalaxyl. Experiments were conducted with two sandy loam and sandy clay soils each amended with two wood doses (5% and 50%) after different incubation times (0, 5 and 12 months). A low wood dose (5%) had no significant impact on the sorption (Kf) of alachlor, but Kf increased for linuron (up to 5.4-1.7 times) and metalaxyl (up to 4.4 and 8.6 times) in all wood-soil systems. The results were not significantly different after different incubation times. The desorption results indicated that wood decreases the sorption irreversibility of alachlor, and increases that of linuron and metalaxyl, with a varying effect of the wood-soil incubation time. The addition of a high wood dose to soil (50%) was more significant for increasing the sorption of all the pesticides, and the sorbed amounts remaining after desorption (>49% for linuron, >33% for alachlor and >6% for metalaxyl), although there was no apparent discrimination between the two types of woods. The role of the nature of the organic carbón (Koc values) for sorption was evidenced for alachlor and metalaxyl, but not for linuron. These outcomes are of interest for extending wood application to soil as a barrier for avoiding environmental risk by point-source pollution due to the use and management of pesticides in farming systems.

Ionic liquid coated magnetic core/shell Fe3O4@SiO2 nanoparticles for the separation/analysis of linuron in food samples.

Three hydrophobic ionic liquids (ILs) including 1-butyl-3-methylimidazole hexafluorophosphate ([BMIM]PF6), 1-hexyl-3-methyl-imidazole hexafluorophosphate ([HMIM]PF6), and 1-octyl-3-methylimidazole hexafluoro-phosphate ([OMIM]PF6) coated Fe3O4@SiO2 nanoparticles with core-shell structure to prepare magnetic solid phase extraction agent (Fe3O4@SiO2@ILs) and establish a new method of magnetic solid phase extraction (MSPE) coupled with UV spectrometry for separation/analysis of linuron. The results showed that linuron was adsorbed rapidly by Fe3O4@SiO2@[OMIM]PF6 and eluanted by ethanol. Under the optimal conditions, preconcentration factor of the proposed method was 10-fold. The linear range, detection limit, correlation coefficient (R) and relative standard deviation (RSD) were found to be 0.04-20.00 µg mL(-1), 5.0 ng mL(-1), 0.9993 and 2.8% (n=3, c=4.00 µg mL(-1)), respectively. The Fe3O4@SiO2 nanoparticles could be used repeatedly for 10 times. This proposed method has been successfully applied to the determination of linuron in food samples.

Uptake, translocation, and elimination in sediment-rooted macrophytes: a model-supported analysis of whole sediment test data.

Understanding bioaccumulation in sediment-rooted macrophytes is crucial for the development of sediment toxicity tests using macrophytes. Here, we explore bioaccumulation in sediment-rooted macrophytes by tracking and modeling chemical flows of chlorpyrifos, linuron, and six PCBs in water-sediment-macrophyte systems. Chemical fluxes across the interfaces between pore water, overlying water, shoots, and roots were modeled using a novel multicompartment model. The modeling yielded the first mass-transfer parameter set reported for bioaccumulation by sediment-rooted macrophytes, with satisfactory narrow confidence limits for more than half of the estimated parameters. Exposure via the water column led to rapid uptake by Elodea canadensis and Myriophyllum spicatum shoots, followed by transport to the roots within 1-3 days, after which tissue concentrations gradually declined. Translocation played an important role in the exchange between shoots and roots. Exposure via spiked sediment led to gradual uptake by the roots, but subsequent transport to the shoots and overlying water remained limited for the chemicals studied. These contrasting patterns show that exposure is sensitive to test set up, chemical properties, and species traits. Although field-concentrations in water and sediment will differ from those in the tests, the model parameters can be assumed applicable for modeling exposure to macrophytes in the field.

Screening of endocrine-disrupting phenols, herbicides, steroid estrogens, and estrogenicity in drinking water from the waterworks of 35 Italian cities and from PET-bottled mineral water.

We investigated contamination by endocrine-disrupting chemicals in drinking water from 35 major Italian cities and five popular Italian brands of bottled mineral water. The quality of Italian drinking water was assessed by combing chemical analysis with bioassay to quantify specific estrogenic contaminants and to characterize the actual biological effect of the mixture of chemicals present in drinking water including the contribution of not targeted compounds. The selected contaminants were natural and synthetic steroid estrogens, alkylphenols and bisphenol A, linuron, triazine herbicides, and their metabolites. A specific analytical method was developed based on solid phase extraction of 1 L of water and concentration to 100 µL for quantification by electrospray ionization liquid chromatography tandem mass spectrometry, achieving quantification limits of 0.05-0.36 ng/L for herbicides and 0.64-7.70 ng/L for steroids and phenols. No steroid estrogens were detected in any of the samples, while bisphenol A and nonylphenols were detected in the ranges of 0.82-102.00 and 10.30-84.00 ng/L respectively. Herbicides and their degradation products, when present, were found from slightly above the quantification limits up to 49.91 ng/L, mainly from cities in northern Italy. Chemical analyses were complemented by the performance of a bioassay for the determination of the estrogenic activity in the extracts based on the transactivation of estrogen receptor α-transfected reporter HeLa-ERE-Luciferase-Neomycin cell line. Activity was generally low with maximum estrogenicity of 13.6 pg/L estradiol equivalents.

Voltammetric determination of the herbicide Linuron using a tricresyl phosphate-based carbon paste electrode.

This paper summarises the results of voltammetric studies on the herbicide 3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea (Linuron), using a carbon paste electrode containing tricresyl phosphate (TCP-CPE) as liquid binder. The principal experimental conditions, such as the pH effect, investigated in Britton-Robinson buffer solutions (pH 2.0-7.0), the peak characteristics for the analyte of interest, or instrumental parameters for the differential pulse voltammetric mode were optimized for the method. As found out, the best electroanalytical performance of the TCP-CPE was achieved at pH 2.0, whereby the oxidation peak of Linuron appeared at ca. +1.3 V vs. SCE. The analytical procedure developed offers good linearity in the concentration range of 1.25-44.20 µg mL(-1) (1.77 × 10(-4)-5.05 × 10(-6) mol L(-1)), showing-for the first time-the applicability of the TCP-CPE for anodic oxidations in direct voltammetry (without accumulation). The method was then verified by determining Linuron in a spiked river water sample and a commercial formulation and the results obtained agreed well with those obtained by the reference HPLC/UV determination.

A mixture of an environmentally realistic concentration of a phthalate and herbicide reduces testosterone in male fathead minnow (Pimephales promelas) through a novel mechanism of action.

Several chemicals that are used by humans, such as pesticides and plastics, are released into the aquatic environment through wastewater and runoff and have been shown to be potent disruptors of androgen synthesis at high concentrations. Although many of these chemicals have been studied in isolation, a large amount of uncertainty remains over how fish respond to low concentrations of anti-androgenic mixtures, which more accurately reflects how such chemicals are present in the aquatic environment. In this study male fathead minnows (FHM) (Pimephales promelas) were exposed to environmentally relevant concentrations of two anti-androgens, the herbicide linuron, and the plasticizer di(2-ethylhexyl) phthalate (DEHP) individually and as part of a mixture of the two for a 28-day period. At the end of this period there was a reduction in plasma testosterone (T) concentrations in male FHM exposed to the mixture, but not in FHM exposed individually to linuron or DEHP or the control FHM. There was also a significant reduction in 17ß-estradiol (E2) in the DEHP-only and mixture exposed groups as compared to the control. Contrary to what has been previously published for these two chemicals in mammals, the lower plasma T concentrations in male FHM exposed to the mixture was not a result of the inhibition of genes involved in steroidogenesis; nor due to an increase in the expression of genes associated with peroxisome proliferation. Rather, an increase in relative transcript abundance for CYP3A4 in the liver and androgen- and estrogen-specific SULT2A1 and SULT1st2 in the testes provides evidence that the decrease in plasma T and E2 may be linked to increased steroid catabolism. Feedback from the pituitary is not repressed as the relative expression of follicle stimulating hormone ß-subunit mRNA transcript levels in the brain was significantly higher in both DEHP and mixture exposed FHM. In addition, luteinizing hormone ß-subunit mRNA transcript levels increased but were not significant in the mixture as compared to the control. Hormone receptor mRNA transcript levels in the liver and testes were not significantly different across all four exposure groups. This study highlights the importance of assessing environmentally relevant concentrations of mixtures when determining risk to aquatic organisms.

Occurrence and distribution of sulfonylurea and related herbicides in central Canadian surface waters 2006-2008.

Surface water sampling in 2006-2008 measured the occurrence of sulfonylureas and related herbicides (SUs) during base flow conditions and wet weather events. Flumetsulam (29.2%), diuron (36.5%) and fomesafen (25.3%) were most frequently detected over the course of the study. Typical SU concentrations were in the low parts per trillion range; however, maximum concentrations of fomesafen (873 ng/L), linuron (856 ng/L) and diuron (2,900 ng/L) approached or exceeded 1 µg/L. The temporal trend in SUs showed a correlation with application periods. In general, detections of SUs were more frequent where rotation of row crops was more intense. Sampling during wet-weather events indicated potential for a range of SUs to be flushed into surface waters at relatively high concentrations.

Investigation of photodegradation and hydrolysis of selected substituted urea and organophosphate pesticides in water.

INTRODUCTION: Photodegradation and hydrolysis of two substituted urea herbicides, monolinuron [3-(4-chlorophenyl)-1-methoxy-1-methylurea] and linuron [3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea], and one organophosphorous insecticide, phoxim [2-(diethoxyphosphinothioyloxyimino)-2-phenylacetonitrile], were studied using buffered sterilized distilled water (pH 4, 7 and 9). METHODS: Experiments were performed in the absence and presence of light (320-740 nm), while the effect of nitrates and humic acids on photodegradation was investigated for all pH values. An analytical method was developed and validated for the determination of target compounds in water samples using liquid chromatography positive ion electrospray-mass spectrometry. RESULTS: According to the results, substituted ureas neither hydrolyzed, at all tested pH values, nor photodegraded at pH 7 and 9. Slow photodegradation of the compounds was observed at pH 4. During 70 days of light exposure, initial concentrations of linuron and monolinuron were decreased by 54% and 31%, respectively, while the presence of nitrates slightly enhanced photodegradation of these compounds. On the other hand, phoxim was found to be very unstable for all the tested conditions and an increase of pH resulted to higher degradation. During hydrolysis experiments, the degradation of the compound ranged from 41% (pH 4) to 85% (pH 9) and the half-lives varied from 10 h (pH 9) to 204 h (pH 4). The presence of light enhanced phoxim degradation and as a result half-lives of 37, 22 and 9h were calculated for pH 4, 7 and 9, respectively. The addition of nitrates and humic acids did not significantly affect the photodegradation of phoxim. CONCLUSIONS: The results indicated that among the three tested pesticides, phoxim found to be the most sensitive in both photodegradation and hydrolysis.

Determination of linuron in water and vegetable samples using stripping voltammetry with a carbon paste electrode.

A carbon paste electrode was used for the electrochemical determination of linuron concentrations in water and vegetable extracts. Optimal conditions were established with respect to electrode activation (electrochemical pretreatment), time accumulation, potential accumulation, scan rate, and pH. The limit of detection achieved with a pre-concentration step was 23.0 µg L(-1). Recovery measurements in vegetable extract and natural water samples were in the range of 98-103%, indicating that the proposed electrochemical method can be employed to analyze linuron in these matrices. The determination results were in good agreement with HPLC results.

Enhanced retention of linuron, alachlor and metalaxyl in sandy soil columns intercalated with wood barriers.

A study has been made of the effect a reactive barrier made of pine (softwood) or oak (hardwood) wood intercalated in a sandy soil column has on the retention of linuron, alachlor and metalaxyl (pesticides with contrasting physicochemical characteristics). The leaching of pesticides has been carried out under a saturated flow regime and breakthrough curves (BTCs) have been obtained at flow rates of 1 m Lmin(-1) (all pesticides) and 3 m Lmin(-1) (linuron). The cumulative curves in the unmodified soil indicate a leaching of pesticides >80% of the total amount of compound added. After barrier intercalation, linuron leaching decreases significantly and a modification of the leaching kinetics of alachlor and metalaxyl has been observed. The theoretical R factors increased ∼2.6-3.3, 1.2-1.6-fold, and 1.4-1.7-fold and the concentration of the maximum peak decreased ∼6-12-fold, 2-4-fold and 1.2-2-fold for linuron, alachlor and metalaxyl, respectively. When considering the three pesticides, significant correlations have been found between the theoretical retardation factor (R) and the pore volume corresponding to the maximum peaks of the BTCs (r=0.77; p<0.05) or the total volume leached (r=-0.78; p<0.05). The results reveal the efficacy of reactive wood barriers to decrease the leaching of pesticides from point sources of pollution depends on the type of wood, the hydrophobicity of the pesticide and the adopted water flow rate. Pine was more effective than oak in decreasing the leaching of hydrophobic pesticide linuron or in decreasing the maximum peak concentration of the less hydrophobic pesticides in soils. Efficacy of these wood barriers was limited for the least hydrophobic pesticide metalaxyl.

[Determination of linuron and its metabolite 3,4-dichloroaniline residues in meat and meat products using liquid chromatography-tandem mass spectrometry].

A method of liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed for the determination of linuron and its metabolite 3, 4-dichloroaniline residues in pork, liver, kidney, casings, canned steam pork and sausage. The sample was extracted with a mixture of acetone-acetonitrile (5: 95, v/v). Most of the lipids in the extract were eliminated by freezing-lipid filtration. After Florisil solid phase extraction cleanup, the linuron and its metabolite residues were determined by LC-MS/MS, and quantified by internal standard meth-od. In the range of 1 - 500 microg/L, both linuron and 3,4-dichloroaniline showed good linearity with the correlation coefficients (r) more than 0. 998. The limit of quantification (S/N > 10) was 10 microg/kg, and the limit of detection (S/N > 3) was 5 microg/kg for each analyte. The recoveries of linuron and 3,4-dichloroaniline in meat and meat products at three spiked levels were in the ranges of 88.3% - 101.2% and 91.6% - 101. 6%, and the relative standard deviations were in the ranges of 4. 8% - 13. 7% and 4. 7% - 11. 8%, respectively. The results demonstrated that the proposed method can meet the requirements for the determination of linuron and 3,4-dichloroaniline in meat and meat products.

[Determination of 88 pesticide residues in cranberry plant extract by gas chromatography-triple quadrupole tandem mass spectrometry].

A method by using a modified QuEChERS (quick, easy, cheap, effective, rugged and safe) and gas chromatography-triple quadrupole tandem mass spectrometry (GC-MS/MS) was established to analyze 88 pesticide residues in cranberry plant extract. The sample was extracted with acetone-hexane (1: 1, v/v) containing 1% acetic acid, then cleaned-up by ethylenediamine-N-propyl silyl (PSA) and graphite carbon (GCB). The extract was determined by GC-MS/MS in multi-reaction monitoring (MRM) mode, and external standard method was applied to quantified the pesticides. All the 88 pesticides showed good linearity in the range of 0. 001 - 0. 2 mg/L, and the limits of quantification (LOQs, S/N > or = 10) were all less than 31. 5 microg/kg. The average recoveries of all the pesticides were in the range of 71. 4% to 116. 6% at three spiked levels of 5, 25 and 50 microg/kg in cranberry plant extract, with the relative standard deviations (RSDs) of 2. 4% - 16. 9%. The results demonstrated that this method is simple, rapid and suitable for the determination of 88 pesticide residues in cranberry plant extract. The analytical sensitivity and accuracy can meet the requirements of multiple pesticide residue analysis.

Transport and degradation of pesticides in a biopurification system under variable flux Part II: A macrocosm study.

Transport of bentazone, isoproturon, linuron, metamitron and metalaxyl were studied under three different flows in macrocosms. The aim was to verify the observations from Part I of the accompanying paper, with an increase in column volume and decrease in chemical and hydraulic load. Very limited breakthrough occurred in the macrocosms for all pesticides, except bentazone, at all flows. From batch degradation experiments, it was observed that the lag time of metamitron and linuron decreased drastically in time for all flows, indicating a growth in the pesticide degrading population. This in contrast to isoproturon and metalaxyl, where an increase in lag time could be observed in time for all flows. From the batch degradation experiments, it could be concluded that the influence of flow on the lag time was minimal and that the inoculation of the pesticide-primed soil had a little surplus value on degradation.

Transport and degradation of pesticides in a biopurification system under variable flux, Part I: a microcosm study.

The efficiency of a biopurification system, developed to treat pesticide contaminated water, is to a large extent determined by the chemical and hydraulic load. Insight into the behaviour of pesticides under different fluxes is necessary. The behaviour of metalaxyl, bentazone, linuron, isoproturon and metamitron was studied under three different fluxes with or without the presence of pesticide-primed soil in column experiments. Due to the time-dependent sorption process, retention of the pesticides with intermediate mobility was significantly influenced by the flux. The higher the flux, the slower pesticides will be sorbed, which resulted in a lower retention. Degradation of the intermediate mobile pesticides was also submissive to variations in flux. An increase in flux, led to a decrease in retention, which in turn decreased the opportunity time for biodegradation. Finally, the presence of pesticide-primed soil was only beneficial for the degradation of metalaxyl.

Determination of phenylurea herbicides in aqueous samples using partitioned dispersive liquid-liquid microextraction.

Partitioned dispersive liquid-liquid microextraction (PDLLME), using THF as the dispersive solvent and dichloromethane as the extraction solvent, was utilized to isolate and concentrate phenylurea herbicides (PUHs) from aqueous samples. In PDLLME, a dispersive solvent should be able to partition in the organic extractant droplets to effectively extract the polar organic compounds from aqueous samples. The mixture of the water-immiscible extractant and the partitioned dispersive solvent was obtained by centrifugation, dried under low pressure, reconstituted in methanol-water mixture (1:1), and injected into a HPLC system for the determination of PUHs. The enrichment factors of the PUHs ranged from 68 to 126 under the optimal conditions. The linear range was 0.5-100 ng ml(-1) for each analyte, the relative standard deviations of PUHs were in the range of 1.5-5.9% (n=5), and the detection limits (signal-to-noise ratio of 3) ranged from 0.10 to 0.28 ng ml(-1) for the herbicides. The range of intraday precision (n=5) for PUHs at the levels of 0.5, 5, and 50 ng ml(-1) were 3.0-5.9%, 1.8-3.3%, and 2.2-3.6%, respectively. The range of interday precision (n=5) at 0.5, 5, and 50 ng ml(-1) were 0.4-1.8%, 1.2-2.4%, and 0.9-2.3%, respectively. The recoveries of PUHs from three spiked river water samples, at a level of 10 ng ml(-1), were 91.2-104.1%. Due to its rapidity, ease of operation, and high recovery, PDLLME can be utilized to isolate and concentrate organic environmental contaminants such as PUHs from aqueous samples.

An experimental design approach employing artificial neural networks for the determination of potential endocrine disruptors in food using matrix solid-phase dispersion.

Matrix solid-phase dispersion (MSPD) as a sample preparation method for the determination of two potential endocrine disruptors, linuron and diuron and their common metabolites, 1-(3,4-dichlorophenyl)-3-methylurea (DCPMU), 1-(3,4-dichlorophenyl) urea (DCPU) and 3,4-dichloroaniline (3,4-DCA) in food commodities has been developed. The influence of the main factors on the extraction process yield was thoroughly evaluated. For that purpose, a 3 fractional factorial design in further combination with artificial neural networks (ANNs) was employed. The optimal networks found were afterwards used to identify the optimum region corresponding to the highest average recovery displaying at the same time the lowest standard deviation for all analytes. Under final optimal conditions, potato samples (0.5 g) were mixed and dispersed on the same amount of Florisil. The blend was transferred on a polypropylene cartridge and analytes were eluted using 10 ml of methanol. The extract was concentrated to 50 microl of acetonitrile/water (50:50) and injected in a high performance liquid chromatography coupled to UV-diode array detector system (HPLC/UV-DAD). Recoveries ranging from 55 to 96% and quantification limits between 5.3 and 15.2 ng/g were achieved. The method was also applied to other selected food commodities such as apple, carrot, cereals/wheat flour and orange juice demonstrating very good overall performance.

Leaching of Diuron, Linuron and their main metabolites in undisturbed field lysimeters.

The increasing use of pesticides in Morocco raises the potential risk of groundwater contamination, notably in the Gharb area, which has a shallow groundwater table. Thus, the leaching of two phenyl-ureas, diuron and linuron and their metabolites through undisturbed soil columns was studied under outdoor conditions. The soil chosen is a loamy clay soil, representative of the Gharb agricultural area. After four irrigation events were applied from 31/03/2005 to 15/05/2005, leachates contained higher amounts of linuron (from 0.08% to 6.96% of applied linuron) than diuron (from 0% to 0.27%). The greater mobility of linuron might be related to its higher water solubility (64 mg x L(- 1) compared with 42 mg x L(- 1) for diuron) and smaller adsorption coefficient (K(oc) of 400 L x kg(- 1), compared with 480 L x kg(- 1) for diuron). Concerning their metabolites, greater amounts of, N'-(3,4-dichlorophenyl)-N, (DCPMU) than N'-3,4-dichlorophenylurea (DCPU) were detected N-dimethylurea in the percolates, from 0% to 0.046% and from 0% to 0.008%, respectively. At the end of the monitoring period, more linuron residues than diuron residues were recovered in the soil profiles, 25.02% and 16.41%, respectively. The diuron residues were found mainly in the 0-20 cm soil layer, whereas linuron residues reached the 20-40 cm soil layer. Under such experimental conditions, linuron leaching, and thus its potential to contaminate groundwater, is greater than that of diuron.

A multi-lysimeter investigation on the mobility and persistence of pesticides in the loam soil of the Fucino Plain (Italy).

In order to evaluate the impact of intensive horticulture on the water resources of the Fucino Plain, one of the most important agricultural settlements of Central Italy, the mobility and persistence in the soil of five commonly used pesticides was investigated by means of multi-lysimeter experiments. The fate of simazine, carbaryl, dicloran, linuron and procymidone was evaluated in the laboratory under experimental conditions simulating as closely as possible both pesticide application and irrigation practices required by the local crops. An efficient extraction procedure followed by chromatographic analysis, allowing the simultaneous determination of the applied chemicals, was used to monitor the pesticide residues in the soil columns as a function of time from application and depth. The experiment, carried out for about 60 days, revealed that soil contamination apparently involves only the surface layer since none of the investigated pesticides was detected at depths greater than 20-30 cm. However, the five pollutants exhibit a quite different behaviour that can be related to their physico-chemical properties.